i-PRO M-JB-MINI-B Round Junction Box for Bullet Cameras
The M-JB-MINI-B is a purpose-built mounting and cable management accessory engineered for i-PRO bullet network cameras, specifically the M-49-V and M-89-F-L models. If you're deploying bullet cameras in retail, corporate, or institutional environments, this junction box handles the mechanical and aesthetic requirements installers actually care about: clean cable routing, minimal ceiling or wall footprint, and a form factor that doesn't draw attention to the mounting infrastructure.
Key Features
- Compact round form factor (104.4mm × 54.5mm): At roughly 4.1 inches wide by 2.15 inches tall, this junction box won't dominate your ceiling or wall installation. In open retail or office spaces where facilities teams scrutinize aesthetics, a low-profile box means faster approval and fewer retrofit requests after deployment.
- Lightweight aluminum alloy construction (0.79 lbs): At less than 0.8 pounds, the M-JB-MINI-B doesn't require additional drywall anchors or structural reinforcement beyond what your camera itself needs. Standard wall studs and ceiling grids support it without issue, reducing installation labor and eliminating callbacks for mounting failures.
- Model-specific engineering for M-49-V and M-89-F-L: This is not a universal junction box. Cable entries, mounting points, and strain relief are fitted specifically to these two i-PRO models, meaning no adapters, no improvisation, and no field fitment work — install and move on. If your cameras are different models or brands, this box will not fit; verify compatibility before ordering.
- Organized cable management: Internal routing separates power (PoE), network, and accessory cables, preventing tangled runs. Cleaner installations reduce troubleshooting time later and speed up camera or cable swaps if a component fails.
- Corrosion-resistant aluminum alloy: Handles temperature fluctuations and humidity without rust or material degradation. Relevant if you're installing in parking structures, loading docks, or any environment where condensation or occasional moisture contact is expected.
- Standard mounting compatibility: Works with both ceiling and wall installations using standard mounting practices. Mounting template provided for accurate hole placement; no special tools or structural prep required. Fits standard wall plates and ceiling grids.
Integration & Compatibility
The M-JB-MINI-B is compatible exclusively with i-PRO M-49-V and M-89-F-L bullet cameras. It integrates with standard PoE infrastructure — no special power requirements, no proprietary connectors. Pair it with PoE switches rated for your camera's power draw and your cabling plan. No firmware or configuration required; it's passive cable routing and mounting hardware only.
When to Choose This Accessory
Select the M-JB-MINI-B if you're deploying M-49-V or M-89-F-L bullet cameras and your installation priorities include cable concealment, aesthetic compliance, and reduced mounting complexity. If your cameras are different i-PRO models or non-i-PRO brands, this box will not fit — verify model compatibility before ordering. For detailed guidance on selecting the right mounting solution for your deployment, consult the camera installation planning guide.
Dimensions and Weight
Compact round profile: 104.4mm wide × 54.5mm tall. Weight 0.79 lbs (approximately 360 grams). These specifications confirm the junction box won't overload wall anchors or add visible bulk to ceiling installations, even in spaces where cable concealment matters aesthetically.
Frequently Asked Questions
Q: Will the M-JB-MINI-B fit cameras other than the M-49-V and M-89-F-L?
A: No. The M-JB-MINI-B is engineered specifically for those two i-PRO models. Using it with other cameras risks poor cable routing and unsecured mounting. Verify your camera model against the compatibility list before purchase.
Q: Do I need additional wall anchors for the M-JB-MINI-B?
A: Not typically. At 0.79 lbs, standard drywall anchors appropriate for the combined weight of the camera and junction box are sufficient. If you're mounting to ceiling grids, no anchors are needed beyond the grid's standard support clips.
Q: Can the M-JB-MINI-B be used for ceiling installations?
A: Yes. The M-JB-MINI-B supports both ceiling and wall mounting. The compact form factor makes it suitable for suspended ceiling grids or drywall ceilings with standard anchors.
Q: Does the M-JB-MINI-B require any configuration or firmware updates?
A: No. The M-JB-MINI-B is a passive accessory — mounting hardware and cable management only. No software, no configuration, no network connectivity. Install it and configure your camera normally.
Q: What cables can the M-JB-MINI-B route?
A: Standard Ethernet (network/PoE) and power cables, plus accessory connections (alarm, audio, etc.) specific to the M-49-V and M-89-F-L. Internal routing separates cable types to minimize interference and tangling.
Q: Is the M-JB-MINI-B suitable for outdoor or high-humidity environments?
A: The aluminum alloy construction resists corrosion from temperature swings and humidity. It's suitable for semi-outdoor or humidity-prone indoor environments (loading docks, parking structures). For full outdoor exposure or submersion risk, consult environmental specifications of your camera model to determine if additional enclosure protection is needed.
Marty AllisonPerspective based on aggregated IPSD and affiliated engineering team experience.
The M-JB-MINI-B (often searched as M JB MINI B) is a straightforward but essential accessory if you're standardizing on M-49-V or M-89-F-L cameras. At 0.79 lbs and 104.4mm × 54.5mm, it's one of the least visually obtrusive junction boxes available — a detail that matters more than it sounds when facilities teams push back on "cable clutter" during initial installation sign-offs.
Technical Highlights:
- Weight and mounting: 0.79 lbs means no reinforcement required beyond standard drywall anchors. Real labor savings on ceiling grid or drywall installations — fewer callback risks, faster installer throughput.
- Aluminum alloy corrosion resistance: Not glamorous, but critical in loading docks, parking structures, or any space with humidity swings. Stainless steel would be overkill for indoor use; aluminum handles condensation and temperature cycling without degradation.
- Model-specific engineering: Cable entries and strain relief are fitted to M-49-V and M-89-F-L only. No universal junction boxes here — that's actually a good thing. Exact fit eliminates improvisation and field fitment work.
Deployment Considerations:
- Compatibility is non-negotiable: This box will not work with other i-PRO models or competitive brands. Verify camera model before ordering — installing it on the wrong camera wastes time and labor.
- Cable routing separation: The M-JB-MINI-B isolates power, network, and accessory connections internally. In real deployments, that reduces troubleshooting time when a cable goes bad or needs replacement. Tangled cables slow diagnostics.
The M-JB-MINI-B is the right choice for retail or corporate installations where aesthetics matter and you're committed to M-49-V or M-89-F-L cameras. It's a no-drama accessory that solves a real problem — keeping cable runs organized and out of sight without adding bulk or complexity to the ceiling or wall footprint.
