DMP · 711

DMP 711 Zone Expansion Module

Network-based zone expansion module with TCP/IP and keypad reader support

• TCP/IP communication plugs into existing Ethernet infrastructure, eliminating proprietary cabling.
• Keypad reader support enables PIN-based credential entry at each expansion zone.
• Runs at 15VDC, integrating cleanly into standard security power distribution backbones.

ELK Products · ELK-0650

ELK Products ELK-0650 ELK Security Accessory

6V 5Ah backup battery for ELK security panels during power loss

• 6V 5Ah auxiliary backup battery for ELK control panels
• 20-hour discharge rate supports moderate alarm and aux loads
• 1.82 lb compact form factor fits standard ELK enclosures

DMP · 263EXT

DMP 263EXT Cellular Extension Module

Cellular expansion module for DMP systems without landline or broadband

• Adds cellular communication to compatible DMP control panels where landline or broadband is unavailable.
• Supports primary or backup cellular path, reducing single-point-of-failure risk at remote sites.
• Integrates within the DMP ecosystem, simplifying procurement and support for existing deployments.

DMP · 270

DMP 270 Network Transient Suppressor

TCP/IP network transient suppressor for cell communicators

• Suppresses TCP/IP ethernet transients to prevent panel resets in multi-building runs.
• Inline, passive installation requires no external power supply or active components.
• Certified UL 294, UL 864, UL 1610, ULC-S304, and additional UL/ULC listings.

DMP · 271

DMP 271 Ground Fault Detection Module

Ground fault detection module for DMP fire alarm systems

• Monitors field wiring against earth ground to catch faults invisible to standard zone supervision.
• Triggers a supervisory zone output so panels annunciate ground faults without raising a fire alarm.
• Supports NFPA 72 and AHJ ground fault annunciation mandates for commercial fire alarm deployments.

DMP · 708

DMP 708 Bus Extender Modules

15VDC bus extender for DMP multi-zone system expansion

• Regenerates LX-Bus signal timing and amplitude to prevent data corruption on long runs.
• Operates across 8–15 VDC input range, compatible with standard DMP distributed power supplies.
• Mitigates EMI and crosstalk in noisy environments alongside power and telephone cabling.

DMP · 710

DMP 710 Bus Splitter/Repeater Module

TCP/IP bus splitter/repeater for multi-building access control networks

• Repeats bus signals over extended runs, eliminating dropouts beyond 500 ft.
• TCP/IP communication supports distributed reader architecture across multi-building sites.
• Runs on 15VDC and wall-mounts at 4.5"×2.75"×1.75" for tight IDF or junction installs.

DMP · 711S

DMP 711S Zone Expansion Module

TCP/IP zone expansion module for compatible DMP security systems

• Adds a single addressable zone via flying-lead to DMP XT/XR panels without hardware replacement.
• TCP/IP communication enables distributed zone supervision across multi-site deployments.
• Ships with 1k ohm resistor; UL 365/864/1076 and CSFM/FDNY listed for fire-rated installs.

DMP · 712-8

DMP 712-8 Zone Expansion Module

8-zone expansion module for DMP panel systems at 15VDC

• Adds 8 supervised burglary zones to a DMP panel without replacing or redesigning the system.
• Plug-in module slot with dip switch addressing keeps installation compact and wiring minimal.
• Pre-installed EOL resistors enable immediate zone supervision straight out of the box.

DMP · 716

DMP 716 Output Expansion Module

15VDC relay expansion for multi-door access control without main panel swap

• DMP output expansion module adds switched outputs to control panels
• 15VDC native DMP platform power - no aux supply required
• Modular expansion drops into existing DMP electrical closet wiring

DMP · 716T

DMP 716T Plug-In Screw Terminal Module

Plug-in screw terminal module for DMP system expansion slots

• Replaces the standard DMP 716 harness with individual screw terminals for field wiring.
• Plug-in connector seats directly into the 716 Output Expansion Module socket—no adapters needed.
• Accepts 18–22 AWG stranded wire, suitable for alarm loops, relay contacts, and 12VDC returns.

DMP · 718T

DMP 718T Plug-In Screw Terminal Module

Plug-in screw terminal module for DMP expansion platforms

• Captive screw terminals eliminate soldering, cutting field termination time during installs.
• Plug-in design fits standard DMP expansion slots, enabling I/O scaling without chassis replacement.
• Compact 4.50×2.75×1.75 in form factor supports wall-mount deployment in tight panel enclosures.

DMP · 719T

DMP 719T Terminal Board Expansion Module

Modular terminal board expansion for DMP systems with plug-in slots

• Extends DMP 714 Zone Expander wiring capacity via direct plug-in — no adapters needed.
• Accepts 14–22 AWG wire with individual 1K EOL resistors for supervised zone circuits.
• Integrated LX-Bus pass-through eliminates external terminal blocks and junction boxes.

DMP · 721T

DMP 721T Terminal Block Module

TCP/IP terminal block module for multi-door access control expansion

• Consolidates zone wiring for DMP XR series panels in a compact box-form module.
• Accepts 14–22 AWG conductors, covering standard sensor and detector loop gauges.
• Pre-installed per-zone EOL resistors eliminate discrete end-of-line components in field.

DMP · 736P

DMP 736P Radionics POPIT Interface Module

• Interfaces DMP systems with Radionics POPIT devices for cross-platform integration.
• Expansion module form factor simplifies addition to existing DMP control panel installations.
• Datasheet available for download to support pre-deployment planning and compliance review.

DMP · 738A

DMP 738A Interface Expansion Module

TCP/IP expansion module for DMP control panels with 12VDC operation

• TCP/IP communication eliminates proprietary serial links for clean network integration.
• Draws 12VDC from existing panel supply rail—no separate regulated power source needed.
• Slot-based form factor (5.5"×3"×0.75") minimizes panel footprint versus stand-alone boxes.

DMP · 763

DMP 763 Wi-Fi Interface Module

Wi-Fi interface for DMP keypad systems—wireless retrofit or new build

• Adds 2.4GHz Wi-Fi to DMP XT/XR panels—no network cable run required.
• Auto-fails over to cellular if Wi-Fi drops, maintaining signal path continuity.
• Draws 12VDC directly from panel supply; no external power adapter needed.

ELK Products · ELK-129

ELK Products Computer Sound Card Interface - ELK-129

Compact 3LCD projector engineered for classrooms and conference rooms where bright, sharp imagery and simple setup matter

• Sound card interface module for ELK panel computer integration
• Plugs into PC sound card for two-way panel audio diagnostics
• Compact 345 x 99 x 261 mm housing for desktop or rack placement

ELK Products · ELK-06120

ELK Products ELK-06120 ELK Security Accessory

6V 12Ah backup battery for ELK security control panels

• 6V 12Ah sealed lead-acid backup battery for ELK alarm panels
• 20-hour discharge rate sustains panels through extended AC outages
• 4.1 lb (1.86 kg) form factor fits standard ELK panel battery bays

ELK Products · ELK-0613

ELK Products ELK-0613 ELK Security Accessory

6V backup battery for ELK security panels during power loss

• 6V 1.3Ah sealed lead-acid backup battery for ELK security panels
• Compact 0.64 lb cell for small panels and low-draw aux circuits
• 20-hour discharge rate keeps panels alive during AC mains loss

ELK Products · ELK-0675

ELK Products ELK-0675 ELK Security Accessory

6V sealed lead-acid backup battery for ELK security panels

• 6V 7.5Ah sealed lead-acid backup battery for ELK panels
• 20-hour discharge rate carries panels through extended outages
• 2.42 lb cell for medium-draw alarm and access control loads

ELK Products · ELK-100

ELK Products ELK-100 ELK Security Accessory

Compact wireless panic button designed to trigger alarm activation independent of system status

• Wireless panic button on a keychain - sub-30g pocket-carry form
• 315 or 433 MHz wireless with 80m line-of-sight range to receivers
• CR2032 coin cell power - no wiring or external supply needed

ELK Products · ELK-101

ELK Products ELK-101 ELK Security Accessory

12VDC access control integration for ELK security systems

• 12VDC security accessory for ELK panel expansion and integration
• 305 mA to 950 mA draw range fits standard ELK aux power budgets
• Compact 1.9 x 2.3 x 0.7 in housing for in-enclosure mounting

ELK Products · ELK-150RT

ELK Products ELK-150RT ELK Security Accessory

8VDC security accessory for ELK control system integration

• Power supply for ELK M1 control boards and access control loads
• 1.2A output at 13.8VDC for door strikes, keypads, and aux devices
• 5 x 5 x 4 in wall-mount housing for low-profile panel placement

ELK Products · ELK-1RT

ELK Products ELK-1RT ELK Security Accessory

Wall-mount security accessory for ELK system integration

• Audio accessory for ELK M1 control boards in 500-7000 Hz range
• Compact 5 x 5 x 4 in wall-mount housing for in-enclosure install
• Ships ready for direct integration with ELK M1 panel architecture

ELK Products · ELK-6010

ELK Products ELK-6010 Security Accessory

ELK security accessory for system expansion and reconfiguration

• Wireless transmitter for ELK security control deployments
• Compact 1.5 x 2.32 x 0.5 in housing for hidden or surface mounting
• Two-way signaling reports enrollment, battery, and tamper status

ELK Products · ELK-6011

ELK Products ELK-6011 Enterprise Access Control Accessory

TCP/IP access control for 6,011 concurrent users across enterprise campuses

• TCP/IP enterprise access control accessory for ELK panels
• Runs on existing Ethernet - no proprietary cabling needed
• Compact 1.5 x 2.32 x 0.5 in housing for in-cabinet mounting

ELK Products · ELK-6020

ELK Products ELK-6020 ELK Security Accessory

TCP/IP networked security accessory for ELK system integration

• TCP/IP networked security accessory for ELK control deployments
• Compact 0.71 x 3.4 x 0.8 in housing for tight in-cabinet spots
• 0.38 lb lightweight unit for overhead and wall-mount installs

ELK Products · ELK-6022

ELK Products ELK-6022 ELK Security Accessory

Wireless transceiver module for ELK M1 Controls systems

• Wireless transceiver module for ELK M1 Controls deployments
• Plug-in install - no M1 system reconfiguration required
• 1.5 x 3 x 0.9 in main housing with magnet for surface mounting

ELK Products · ELK-6023

ELK Products ELK-6023 ELK Security Accessory

Wireless transceiver for ELK M1 control systems

• 902-928 MHz frequency-hopping wireless for crowded RF environments
• Pairs with ELK M1 panels for two-way sensor signaling
• Compact 2.5 in housing with 3.6V lithium 1/2 AA battery

ELK Products · ELK-6040

ELK Products ELK-6040 Security System Accessory

Omni-directional microphone accessory for ELK control platform expansion

• Omnidirectional 360-degree microphone for ELK panel audio integration
• Compact 4.25 x 3.13 x 1.70 in housing for ceiling or wall placement
• Adds room audio capture to ELK security system deployments

ELK Products · ELK-6052

ELK Products ELK-6052 ELK Security Accessory

White smoke detection accessory for ELK security systems

• White smoke detector accessory for ELK security panel integration
• 4.63 in diameter x 2.25 in low-profile ceiling and wall mounting
• Drops into existing ELK alarm panel sensor architecture

ELK Products · ELK-6053

ELK Products ELK-6053 ELK Security Accessory

N ELK Products security accessory designed to integrate with ELK access control and alarm system installations

• Transformer accessory for ELK access control and alarm systems
• Drops into ELK panel power architecture without rewiring
• Ships ready for in-cabinet integration with ELK control platforms

ELK Products · ELK-800

ELK Products ELK-800 TCP/IP Security Accessory

TCP/IP accessory for multi-door access control across distributed sites

• Native TCP/IP networked security accessory for ELK panel deployments
• Drops onto existing Ethernet - no serial converter or gateway needed
• Compact 4.5 x 3 x 1.2 in housing for in-cabinet placement

ELK Products · ELK-IP232

ELK Products ELK-IP232 IP to Serial Interface

IP-to-RS-232 serial converter for legacy device integration

• IP-to-RS-232 serial bridge connects legacy readers to IP networks
• Wall, corner, or column mount fits closet and equipment-rack installs
• Adds Ethernet reach to RS-232 ELK panel and 3rd-party serial devices

ELK Products · ELK-M1BLOCKS

ELK Products ELK-M1BLOCKS M1 Gold Terminal Blocks

Gold-plated terminal blocks for ELK M1 control panel wiring

• Gold-plated terminal blocks resist corrosion on M1 panel wiring
• Screw-terminal connections for secure field wiring termination
• Drops into ELK M1 Gold control panel for clean cable management