ELK Products ELK-0613 6V 1.3Ah Backup Battery
Overview
The ELK-0613 is a 6-volt, 1.3Ah sealed backup battery built as a replacement power cell for security control panels and low-voltage life-safety enclosures that spec a compact 6V standby source. At roughly 0.64 lbs (0.29 kg), it drops into panel enclosures where every cubic inch of backup power budget is accounted for and a heavier 12V pack isn't the right fit. If you're maintaining a fleet of ELK panels or any control enclosure speced for a 6V/1.3Ah standby cell, the ELK-0613 is the direct replacement to stock.
Key Features
- 6V Nominal Voltage: matches control panels and low-voltage enclosures engineered around a 6-volt standby rail — don't substitute a 12V pack here, the voltage mismatch will either underpower the board or trip a fault condition.
- 1.3Ah Rated Capacity (20-hour rate): gives the panel a defined runway during a mains outage; on a 20-hour discharge curve this is sized for short-to-moderate utility interruptions rather than multi-day standby, so match it against your panel's documented backup-time requirement before ordering in bulk.
- 0.64 lbs (0.29 kg) compact form factor: light enough to ship economically in multi-unit replacement orders and small enough to fit tight panel enclosures without reworking the mounting tray.
- Period (Months) storage rating: batteries lose capacity on the shelf — plan replacement cycles and rotate stock rather than letting spares sit past their storage window, especially for panels in service contracts with defined backup-time SLAs.
Integration & Compatibility
The ELK-0613 (often searched as ELK 0613) is sized as a like-for-like swap for control panels and enclosures originally speced with a 6V/1.3Ah battery. Before ordering, confirm the panel's battery compartment and connector match a standard 6V/1.3Ah form factor — voltage and capacity are the two numbers that matter most when cross-referencing against an OEM part.
Frequently Asked Questions
Q: What voltage and capacity does the ELK-0613 provide?
A: The ELK-0613 is rated 6 volts nominal at 1.3Ah on a 20-hour discharge rate.
Q: How much does the ELK-0613 weigh?
A: Approximately 0.64 lbs (0.29 kg).
Q: Is the ELK-0613 a direct replacement for other 6V/1.3Ah batteries?
A: It's built to the same 6V nominal, 1.3Ah (20-hour rate) specification used in control panels and enclosures speced for that battery size — confirm your panel's original battery spec matches before ordering.
Q: How should the ELK-0613 be stored before installation?
A: The battery carries a storage capacity rating measured in months; rotate spare stock within that window rather than holding it indefinitely on a shelf.
The ELK-0613 is a straightforward part to spec once you know what you're solving for: a 6V, 1.3Ah backup cell at the 20-hour discharge rate, weighing in at 0.64 lbs. I get asked why this isn't a 12V pack — because the panel it's replacing was designed around a 6-volt standby rail, and swapping voltage classes on a control panel battery is not a judgment call you want to make in the field.
Technical Highlights:
- 6V Nominal Voltage: keeps the replacement electrically matched to panels engineered for a 6-volt backup rail — critical since a 12V substitute can overdrive or fault the board.
- 1.3Ah Rated Capacity (20-hour rate): defines how long the panel rides through a power outage; size your maintenance cycle around this number rather than assuming standard multi-day runtime.
- 0.64 lbs (0.29 kg): light enough for techs to carry several as truck stock without adding meaningful weight to a service bag.
Deployment Considerations:
- Confirm the existing panel's battery bay and terminal style accept a standard 6V/1.3Ah cell before pulling the old one — this is a spec-match replacement, not a universal fit.
- The Period (Months) storage rating means shelf-stocked spares degrade over time; date and rotate inventory rather than holding units indefinitely.
Good stock item for service techs maintaining ELK control panels on a standing service contract, where a dead backup battery on a scheduled inspection means a same-visit swap instead of a return trip. Order ELK-0613 units in the quantity that matches your panel count plus a shelf-rotation buffer.
