WiremoldT10FC-FW Full Capacity Raceway Entrance End Fitting

The 2410FC-FW is a full-capacity entrance end fitting built for the Wiremold 2400 Series raceway system — the connector piece that lets cable runs transition cleanly from wall or ceiling penetrations into surface raceway without crimping conductor bend radius. It's a small component, but on a structured cabling or security wiring job it's the difference between a code-compliant entrance and a stuffed, kinked mess behind the faceplate. The model number 2410FC-FW identifies the full-capacity variant sized specifically for 2400 Series channel.

Overview

This fitting terminates a 2400 Series raceway run at a wall or ceiling entrance point, giving low-voltage and power conductors a supported transition into the raceway channel. It's rated for indoor use and carries a 600V voltage rating, which covers both electrical wire and copper/fiber data cabling routed through the same cable management system.

Key Features

• 3/4in and 1in concentric trade-size knockouts on each side: gives installers two conduit-entry options per side without ordering a different fitting for each conduit size — cuts SKU count on a multi-run job.
• 600V rating: clears the bar for standard building power circuits as well as low-voltage runs, so the same fitting works whether the raceway is carrying line-voltage or communications cable.
• Compact footprint (2.625in L x 3.0in W x 2.25in H): fits tight entrance points near door frames and corner transitions where a bulkier fitting won't clear.
• 0.43 lb weight: light enough that it doesn't add meaningful load to a raceway run or require extra bracing at the entrance point.
• Full-capacity design: matches the internal channel capacity of 2400 Series raceway rather than a reduced-capacity fitting, so conductor fill calculated for the raceway run carries straight through the entrance without a bottleneck.

Integration & Compatibility

The 2410FC-FW is purpose-built for 2400 Series raceway and is not a universal fitting — confirm your raceway generation before ordering. It pairs naturally with other 2400 Series components when you're planning a full run from entrance to device drop, and it's a common companion part on jobs that also spec racks and cabinets or video surveillance camera drops where power and data need a clean wall entrance. If you're scoping a larger low-voltage pathway, a PoE planning guide is worth a read before finalizing conduit and raceway sizing for the run.

Frequently Asked Questions

Q: What raceway series does the 2410FC-FW fit?

A: The 2410FC-FW is built for 2400 Series raceway specifically — it is a full-capacity entrance end fitting sized to that channel.

Q: What size conduit knockouts does it have?

A: It has 3/4in and 1in concentric trade-size knockouts located on each side of the fitting.

Q: Is the 2410FC-FW rated for indoor or outdoor use?

A: It is rated for indoor use only.

Q: What voltage is the 2410FC-FW rated for?

A: It carries a 600V rating, covering both power and low-voltage data applications.

Q: How much does the 2410FC-FW weigh?

A: It weighs 0.43 lb.

Jerry Tildsen

The 2410FC-FW comes up on jobs where a cable run has to punch through a wall and land in 2400 Series raceway without choking down the conductor count. It's a small part, but ordering the wrong entrance fitting means a return trip to the supply house mid-install.

Technical Highlights:

• Dual concentric knockouts (3/4in and 1in): one fitting covers two common conduit sizes per side, so you're not stocking a separate SKU for each conduit diameter feeding the entrance.
• 600V rating: rated high enough to share raceway with building power circuits, not just low-voltage cabling, which matters when a run is mixed-use.
• Full-capacity channel match: the internal capacity matches 2400 Series raceway itself, so you don't lose conductor fill at the entrance point the way you would with a reduced-capacity fitting.

Deployment Considerations:

• Confirm the raceway generation on site before ordering — 2410FC-FW is sized for 2400 Series specifically and won't correctly seat on a different raceway family.
• At 2.625in x 3.0in x 2.25in, it's compact enough for tight entrance points, but that also means fill capacity is finite — plan conductor count before the run, not after.

Specify the 2410FC-FW anywhere a 2400 Series raceway run needs a clean, code-compliant wall or ceiling entrance — typical on commercial retrofit jobs where surface raceway is carrying both power and structured cabling into a single drop point.