Middle Atlantic 2410D-FW Cable Entrance End Fitting

Overview

The Middle Atlantic 2410D-FW is an entrance end fitting finished in Fog White, built to cap and finish the entry point of a Middle Atlantic cable routing or raceway run. Entrance end fittings like the 2410D-FW close out the open end of a duct or raceway section where cabling transitions into a rack, enclosure, or wall opening — a small part with an outsized effect on how clean a rack elevation or equipment room looks once the low-voltage cabling is dressed in. The 2410D-FW (often searched as 2410D FW) is TAA-compliant, which matters if this fitting is going into a government, federal integrator, or public-sector install with Trade Agreements Act sourcing requirements written into the procurement spec.

Key Features

• Fog White finish: matches Middle Atlantic's Fog White rack and enclosure line, so the fitting doesn't stand out as an off-color patch against the rest of the cabinet or raceway run — a detail that matters on any install where the equipment room is visible to clients or auditors.
• TAA-compliant sourcing: the 2410D-FW is documented as TAA Compliant, which lets integrators specify it into federal and federally-funded projects that require Trade Agreements Act conformance without a separate sourcing exception.
• Entrance end fitting form factor: designed specifically to terminate and finish the entry end of a cable routing run rather than serve as a generic cover plate, so it fits the specific role Middle Atlantic's raceway and duct systems call for at a run's origin point.

Integration & Compatibility

As an entrance end fitting, the 2410D-FW is designed to pair with Middle Atlantic's cable routing and raceway hardware rather than function as a standalone part. If you're speccing a full run, check the Middle Atlantic catalog for the matching duct, raceway, or channel sections this fitting is intended to close out, and confirm finish and width match across every fitting in the run before ordering. For broader rack build-outs, it's worth reviewing a PoE and cable planning guide early in the design phase — end fittings, raceway, and cable management all get specified together, and getting the run length and termination points right up front avoids ordering a second fitting later. This fitting is a cable management accessory, not a networking or power component, so it has no interaction with NVR or IP camera electronics beyond dressing the cabling that runs to them. If the install also includes PoE switches or other rack-mounted gear, plan the raceway and entrance fittings as one system so the finish and fitting count are consistent from switch to camera drop.

Frequently Asked Questions

Q: Is the 2410D-FW TAA compliant?

A: Yes, the 2410D-FW is documented as TAA Compliant, making it eligible for specification into government and federally-funded procurement that requires Trade Agreements Act conformance.

Q: What color/finish does the 2410D-FW come in?

A: The 2410D-FW ships in Fog White, matching Middle Atlantic's Fog White enclosure and raceway finish line.

Q: What is an entrance end fitting used for?

A: It terminates and finishes the entry end of a Middle Atlantic cable routing or raceway run, closing out the open end where cabling transitions into a rack or wall opening.

Q: Does the 2410D-FW need to match other components in my raceway run?

A: Yes — as an entrance end fitting, it's intended to pair with Middle Atlantic's raceway and duct hardware, so finish and sizing should be confirmed against the rest of the run before ordering.

Ted Perry

The 2410D-FW is a small part of a rack build-out, but it's the kind of small part that separates a finished equipment room from one that looks half-done. This is Middle Atlantic's Fog White entrance end fitting, and the finish match is the whole point — 2410D-FW exists so the end of your raceway run doesn't look like an afterthought.

Technical Highlights:

• Fog White finish: matches Middle Atlantic's Fog White rack and raceway line so the fitting blends into the run instead of reading as a mismatched patch.
• TAA Compliant: documented TAA compliance means this fitting can go on a federal or federally-funded bill of materials without a sourcing exception.
• Entrance end fitting design: purpose-built to terminate the entry point of a routing run, not a generic blank or cover plate.

Deployment Considerations:

• Order this alongside the matching raceway or duct sections from the same finish family — mismatched fittings on a single run are the most common callback on rack finish-out work.
• The evidence here doesn't include dimensions, so confirm fit against your specific raceway width before finalizing a multi-unit order.

Spec the 2410D-FW when you're closing out a Fog White raceway run on a federal or TAA-restricted project and need the finish and compliance paperwork to match without exception.