DMP · 718T

DMP 718T Plug-In Screw Terminal Module

Plug-in screw terminal module for DMP expansion platforms

• Captive screw terminals eliminate soldering, cutting field termination time during installs.
• Plug-in design fits standard DMP expansion slots, enabling I/O scaling without chassis replacement.
• Compact 4.50×2.75×1.75 in form factor supports wall-mount deployment in tight panel enclosures.

DMP · 719T

DMP 719T Terminal Board Expansion Module

Modular terminal board expansion for DMP systems with plug-in slots

• Extends DMP 714 Zone Expander wiring capacity via direct plug-in — no adapters needed.
• Accepts 14–22 AWG wire with individual 1K EOL resistors for supervised zone circuits.
• Integrated LX-Bus pass-through eliminates external terminal blocks and junction boxes.

DMP · 721T

DMP 721T Terminal Block Module

TCP/IP terminal block module for multi-door access control expansion

• Consolidates zone wiring for DMP XR series panels in a compact box-form module.
• Accepts 14–22 AWG conductors, covering standard sensor and detector loop gauges.
• Pre-installed per-zone EOL resistors eliminate discrete end-of-line components in field.

DMP · 736P

DMP 736P Radionics POPIT Interface Module

• Interfaces DMP systems with Radionics POPIT devices for cross-platform integration.
• Expansion module form factor simplifies addition to existing DMP control panel installations.
• Datasheet available for download to support pre-deployment planning and compliance review.

DMP · 738A

DMP 738A Interface Expansion Module

TCP/IP expansion module for DMP control panels with 12VDC operation

• TCP/IP communication eliminates proprietary serial links for clean network integration.
• Draws 12VDC from existing panel supply rail—no separate regulated power source needed.
• Slot-based form factor (5.5"×3"×0.75") minimizes panel footprint versus stand-alone boxes.

DMP · 763

DMP 763 Wi-Fi Interface Module

Wi-Fi interface for DMP keypad systems—wireless retrofit or new build

• Adds 2.4GHz Wi-Fi to DMP XT/XR panels—no network cable run required.
• Auto-fails over to cellular if Wi-Fi drops, maintaining signal path continuity.
• Draws 12VDC directly from panel supply; no external power adapter needed.

DMP · 861

DMP 861 Power Distribution/4 Wire Bus Module

Centralized power & 4-wire bus module for multi-keypad access systems

• 4-wire bus connectivity synchronizes multiple keypads and readers from one module.
• Centralized 12V/24V DC power distribution eliminates distributed point-of-load supplies.
• Compact form factor mounts in existing DMP cabinets with no separate power supply needed.

DMP · 865

DMP 865 Style W/X Notification Module

TCP/IP notification module for DMP control panel auxiliary expansion

• TCP/IP integration eliminates dedicated serial runs in DMP control panel networks.
• Monitors opens, shorts, and ground faults on notification circuits in real time.
• Operates at 9.6–14.2 VDC, compatible with panel-mounted or remote 24VDC supplies.

DMP · 866

DMP 866 Notification Module

12VDC auxiliary notification module for DMP access control expansion

• Runs on 12VDC, integrating directly into existing access control cabinet power supplies.
• Auxiliary architecture adds notification endpoints without disrupting active panel configs.
• Scales multi-door and multi-reader deployments without replacing core control infrastructure.

DMP · 869

DMP 869 Style D Initiating Module

25VDC initiating module expands DMP security system zones

• Two independent supervised 4-wire initiating circuits expand DMP panel zone capacity.
• 8–25 VDC operating range integrates directly with standard DMP power distribution.
• Continuous ground-fault supervision detects wiring opens, shorts, and faults pre-alarm.

DMP · 893A

DMP 893A Dual Phone Line Module Keypad

Dual phone line keypad module for DMP access control expansion

• Monitors main and backup phone lines for voltage drops, alerting local keypads and central station.
• UL 864 listed and FCC Part 15/68 compliant, meeting fire signaling and telecom regulatory requirements.
• Installs into DMP panel enclosure at 12VDC via wire harness, fitting existing auxiliary expansion slots.

DMP · ES501

DMP ES501 Plug-In Transformer Enclosure

Compact transformer enclosure for DMP NFC/13.56MHz access control

• Hinged metal cover with built-in venting protects transformers while dissipating heat.
• Compact 4.25″×5.625″×2.5″ footprint consolidates transformer power at the control panel.
• Supports low-voltage transformers rated over 20 VA for DMP access control installations.

DMP · ES502

DMP ES502 Transformer Enclosure

Isolated transformer housing for DMP control panel systems

• Vented metal housing protects transformers 20 VA and above from dust and accidental contact.
• Compact 4.25" × 5.625" × 3.75" footprint integrates into standard DMP control panel layouts.
• Hinged cover enables fast one-handed transformer access for maintenance in wall-mount installs.

ELK Products · ELK-129

ELK Products Computer Sound Card Interface - ELK-129

Compact 3LCD projector engineered for classrooms and conference rooms where bright, sharp imagery and simple setup matter

• Sound card interface module for ELK panel computer integration
• Plugs into PC sound card for two-way panel audio diagnostics
• Compact 345 x 99 x 261 mm housing for desktop or rack placement

ELK Products · ELK-06120

ELK Products ELK-06120 ELK Security Accessory

6V 12Ah backup battery for ELK security control panels

• 6V 12Ah sealed lead-acid backup battery for ELK alarm panels
• 20-hour discharge rate sustains panels through extended AC outages
• 4.1 lb (1.86 kg) form factor fits standard ELK panel battery bays

ELK Products · ELK-0613

ELK Products ELK-0613 ELK Security Accessory

6V backup battery for ELK security panels during power loss

• 6V 1.3Ah sealed lead-acid backup battery for ELK security panels
• Compact 0.64 lb cell for small panels and low-draw aux circuits
• 20-hour discharge rate keeps panels alive during AC mains loss

ELK Products · ELK-0675

ELK Products ELK-0675 ELK Security Accessory

6V sealed lead-acid backup battery for ELK security panels

• 6V 7.5Ah sealed lead-acid backup battery for ELK panels
• 20-hour discharge rate carries panels through extended outages
• 2.42 lb cell for medium-draw alarm and access control loads

ELK Products · ELK-100

ELK Products ELK-100 ELK Security Accessory

Compact wireless panic button designed to trigger alarm activation independent of system status

• Wireless panic button on a keychain - sub-30g pocket-carry form
• 315 or 433 MHz wireless with 80m line-of-sight range to receivers
• CR2032 coin cell power - no wiring or external supply needed

ELK Products · ELK-101

ELK Products ELK-101 ELK Security Accessory

12VDC access control integration for ELK security systems

• 12VDC security accessory for ELK panel expansion and integration
• 305 mA to 950 mA draw range fits standard ELK aux power budgets
• Compact 1.9 x 2.3 x 0.7 in housing for in-enclosure mounting

ELK Products · ELK-150RT

ELK Products ELK-150RT ELK Security Accessory

8VDC security accessory for ELK control system integration

• Power supply for ELK M1 control boards and access control loads
• 1.2A output at 13.8VDC for door strikes, keypads, and aux devices
• 5 x 5 x 4 in wall-mount housing for low-profile panel placement

ELK Products · ELK-1RT

ELK Products ELK-1RT ELK Security Accessory

Wall-mount security accessory for ELK system integration

• Audio accessory for ELK M1 control boards in 500-7000 Hz range
• Compact 5 x 5 x 4 in wall-mount housing for in-enclosure install
• Ships ready for direct integration with ELK M1 panel architecture

ELK Products · ELK-6010

ELK Products ELK-6010 Security Accessory

ELK security accessory for system expansion and reconfiguration

• Wireless transmitter for ELK security control deployments
• Compact 1.5 x 2.32 x 0.5 in housing for hidden or surface mounting
• Two-way signaling reports enrollment, battery, and tamper status

ELK Products · ELK-6011

ELK Products ELK-6011 Enterprise Access Control Accessory

TCP/IP access control for 6,011 concurrent users across enterprise campuses

• TCP/IP enterprise access control accessory for ELK panels
• Runs on existing Ethernet - no proprietary cabling needed
• Compact 1.5 x 2.32 x 0.5 in housing for in-cabinet mounting

ELK Products · ELK-6020

ELK Products ELK-6020 ELK Security Accessory

TCP/IP networked security accessory for ELK system integration

• TCP/IP networked security accessory for ELK control deployments
• Compact 0.71 x 3.4 x 0.8 in housing for tight in-cabinet spots
• 0.38 lb lightweight unit for overhead and wall-mount installs

ELK Products · ELK-6022

ELK Products ELK-6022 ELK Security Accessory

Wireless transceiver module for ELK M1 Controls systems

• Wireless transceiver module for ELK M1 Controls deployments
• Plug-in install - no M1 system reconfiguration required
• 1.5 x 3 x 0.9 in main housing with magnet for surface mounting

ELK Products · ELK-6023

ELK Products ELK-6023 ELK Security Accessory

Wireless transceiver for ELK M1 control systems

• 902-928 MHz frequency-hopping wireless for crowded RF environments
• Pairs with ELK M1 panels for two-way sensor signaling
• Compact 2.5 in housing with 3.6V lithium 1/2 AA battery

ELK Products · ELK-6040

ELK Products ELK-6040 Security System Accessory

Omni-directional microphone accessory for ELK control platform expansion

• Omnidirectional 360-degree microphone for ELK panel audio integration
• Compact 4.25 x 3.13 x 1.70 in housing for ceiling or wall placement
• Adds room audio capture to ELK security system deployments

ELK Products · ELK-6052

ELK Products ELK-6052 ELK Security Accessory

White smoke detection accessory for ELK security systems

• White smoke detector accessory for ELK security panel integration
• 4.63 in diameter x 2.25 in low-profile ceiling and wall mounting
• Drops into existing ELK alarm panel sensor architecture

ELK Products · ELK-6053

ELK Products ELK-6053 ELK Security Accessory

N ELK Products security accessory designed to integrate with ELK access control and alarm system installations

• Transformer accessory for ELK access control and alarm systems
• Drops into ELK panel power architecture without rewiring
• Ships ready for in-cabinet integration with ELK control platforms

ELK Products · ELK-800

ELK Products ELK-800 TCP/IP Security Accessory

TCP/IP accessory for multi-door access control across distributed sites

• Native TCP/IP networked security accessory for ELK panel deployments
• Drops onto existing Ethernet - no serial converter or gateway needed
• Compact 4.5 x 3 x 1.2 in housing for in-cabinet placement

ELK Products · ELK-912

ELK Products ELK-912 Security Controller

12VDC controller for multi-door access & alarm coordination

• 12VDC relay controller for low-voltage security panel integration
• 30 mA draw when relay energized - fits standard aux power budgets
• Compact 1.1 x 1.55 in (28 x 39 mm) housing for in-cabinet mount

ELK Products · ELK-912B

ELK Products ELK-912B ELK Security Accessory

24VDC auxiliary power distribution for ELK security panels

• 24VDC relay accessory for ELK alarm and access panel integration
• 35 mA draw when relay energized - low aux power budget impact
• Compact 2 x 1.5 in (51 x 38 mm) housing fits standard enclosures

ELK Products · ELK-9200

ELK Products ELK-9200 ELK Security Accessory

ELK security accessory for access control and monitoring integration

• Multi-protocol controller hub - UPB, Insteon, Z-Wave, Zigbee, X10
• 110 VAC operation drives whole-home automation from one chassis
• 12 x 12 x 3.375 in enclosure for wall-mount install in mech rooms

ELK Products · ELK-924

ELK Products ELK-924 ELK Security Accessory

Compact wireless panic button designed to activate an alarm system regardless of current system status

• Wireless panic button triggers alarm regardless of system state
• Sub-30g keychain form factor (52 x 54.5 x 10 mm) for pocket carry
• CR2032 coin cell power - no wiring or external supply needed

ELK Products · ELK-9244

ELK Products ELK-9244 Sensitive Relay DPDT 12/24 VDC

DPDT sensitive relay, 12/24 VDC jumper-selectable for mixed-voltage systems

• DPDT relay switches two independent circuits from one coil signal
• 12 or 24 VDC coil voltage matches standard ELK panel power buses
• Drops into ELK panel for compound door, strike, and aux switching

ELK Products · ELK-930

ELK Products ELK-930 TCP/IP Network Security Accessory

TCP/IP network accessory for centralized ELK security monitoring

• TCP/IP networked security accessory for ELK control deployments
• Native IP integration - no proprietary gateway or converter needed
• Compact 3.4 x 2.75 x 0.625 in housing weighs 0.12 lb for tight spaces