DMP

SKU: 1136

DMP 1136 Wireless Remote Chime

Wireless chime for access control with audio-visual alerts, no hardwired sounder lines

• Wireless operation eliminates dedicated audio cable runs to doors, docks, and remote zones.
• Keypad-based sounder triggers on door events or credential reads with per-zone event mapping.
• Compact 2.6" W × 5" H × 1.5" D form factor fits standard access control mounting locations.

DMP

SKU: 1139

DMP 1139 Wireless Bill Trap

Wireless bill trap for panic-holdup systems without hardwired installation

• Wireless transmission eliminates hardwired loops to teller windows and service counters.
• Includes two CR2450 coin cell batteries, enabling deployment without external power runs.
• Compact bracket (2.5" L × 1.3" W) supports discreet mounting in transaction zone retrofits.

DMP

SKU: 1142-GUARD

DMP 1142-GUARD Under-Desk Hold-Up Transmitter Guard

Concealed under-desk mount for DMP wireless panic-holdup transmitters

• Purpose-built guard ensures mechanical fit with DMP wireless panic-holdup transmitters.
• Under-desk concealed mount prevents tampering and accidental activation in high-traffic areas.
• Ergonomic guard design allows authorized staff rapid two-button activation during incidents.

DMP

SKU: 1148-G

DMP 1148-G Personal Pendant Wireless Panic Button

Wireless pendant for panic and holdup alerts in commercial facilities

• Wearable panic button transmits wireless emergency alerts without reaching a hardwired device.
• Status LED confirms signal transmission to the receiver, enabling rapid deployment verification.
• Pre-installed non-removable battery eliminates ongoing maintenance; water-resistant for typical indoor use.

DMP

SKU: 1154

DMP 1154 Wireless Four-Zone Input Module

Four wireless zones for door/window monitoring with HID and NFC support

• Four independent wireless zones accept legacy door/window contacts with no new conduit runs.
• Supports HID and NFC/13.56MHz credentials, reducing reader hardware across distributed sites.
• 12VDC operation allows CR123A battery or PS12-5 supply for flexible permanent or temp installs.

DMP

SKU: 1158

DMP 1158 Wireless 8-Zone Input Module

Wireless 8-zone input module for retrofit door/window monitoring without cables

• Eight independent 12VDC zone inputs cover doors and windows without new cable runs.
• Wireless connectivity eliminates conduit work in retrofits, leased spaces, and warehouses.
• Integrates with DMP control panel ecosystems to expand zone capacity without panel replacement.

DMP

SKU: GP-23

DMP GP-23 Hidden Wire Surface Mount Magnetic Contact

Surface mount magnetic contact for DMP door and window monitoring

• Surface mount design eliminates frame drilling, simplifying retrofits and commercial installs.
• 1-inch rated gap tolerance gives installers reliable trigger thresholds on doors and windows.
• Concealed screws and multi-direction wire routing reduce visible footprint and deter tampering.

DMP

SKU: MET-44WG-18

DMP MET-44WG-18 Overhead Contact

TCP/IP overhead contact for networked door/window detection

• TCP/IP communication eliminates dedicated analog wiring runs to each sensor point.
• Overhead form factor enables ceiling or transom mounting without door-frame hardware.
• Integrates directly with DMP TCP/IP-zone-capable control panels and management systems.

DMP

SKU: P2S-001

DMP P2S-001 High Security Single Zone Magnetic Sensor

Single zone magnetic sensor for door/window monitoring with HID integration

• Single-zone magnetic detection simplifies per-door/window wiring in multi-zone panels.
• HID credential integration correlates door contact events with cardholder access logs.
• Intrusion/contacts cable category ensures signal compatibility with standard detection circuits.

DMP

SKU: SM-20WG

DMP SM-20WG 3" Wide Gap Magnetic Reed Contact

3" wide gap magnetic reed contact for networked door monitoring

• 3-inch operating gap handles reinforced steel frames and non-standard door geometries.
• TCP/IP connectivity enables remote event logging across distributed perimeter door networks.
• Supports up to 500 NFC/13.56MHz credentials for multi-zone access control deployments.

DMP

SKU: STB-10

DMP STB-10 3/8" Recessed Contact

3/8" recessed contact for concealed door and window monitoring

• 3/8" recessed body fits tight door and window frame cavities for flush, hidden install.
• Closed-loop wiring integrates directly with DMP panels and standard intrusion alarm systems.
• Miniature form factor eliminates surface-mount housing, keeping hardware invisible post-install.

DSC

SKU: PG9939

DSC PG9939 Wireless Temperature Sensor

Wireless temperature sensor for DSC systems, -20°C to 50°C range

• PG9939 wireless temperature sensor, -20C to 50C
• 128-bit AES encryption on CR2032 lithium battery
• Up to 5-year battery life for facility monitoring

Eaton

SKU: 103006348-001

Eaton Kit (Harness Extention ERM to UPS) - 103006348-001

• Harness extension kit for ERM module to UPS cable runs
• Adds reach when standard cable run is insufficient
• Preserves ERM connectivity for distant rack placement

Eaton

SKU: 103005822

Eaton Temperature & Humidity Sensor TH-Module - 103005822

• Temperature and humidity sensor module for environmental monitoring
• Detects thermal runaway and condensation risk in equipment racks
• Integrates with Eaton UPS and PDU management systems

ELK Products

SKU: ELK-6021

ELK Products ELK-6021 M1 Controls Transceiver

M1 Controls transceiver for signal extension and module communication

• Wireless transceiver for ELK M1 Controls panel deployments
• Native M1 protocol - no translation layer or custom firmware
• Compact 1.1 x 2.3 x 0.25 in housing for in-cabinet mounting

ELK Products

SKU: ELK-WA003

ELK Products ELK-WA003 Remote Cellular Antenna

Remote cellular antenna for ELK systems with flexible pole/corner mounting

• Remote cellular antenna extends signal reach for ELK communicators
• Pole, corner, or column mount for signal-optimal placement
• Cable run to ELK cellular module recovers low-signal install zones