2N 03369-001 vs Hanwha TID-600R: Specification Comparison
Both the 2N 03369-001 (IP Force 5MP) and the Hanwha TID-600R are wired, PoE-powered outdoor video intercoms designed for door-station and access-control applications. Each integrates a camera, two-way audio, and IP network connectivity into a wall-mount form factor intended for lobby, gate, or building-entrance deployment. Buyers evaluating these units are typically choosing between them for single-entry or multi-entry access points where video identification, remote communication, and integration with either an intercom platform or SIP/VoIP infrastructure are the primary requirements.
In This Guide
- Which unit delivers better visitor imaging and on-device identification capability?
- How do the two units differ in audio, VoIP, and platform integration?
- Which unit is better suited for harsh outdoor environments and what are the installation power requirements?
- Which should you choose: the 03369-001 or the TID-600R?
- Side-by-Side Specs
- FAQ
Which unit delivers better visitor imaging and on-device identification capability?
The 2N 03369-001 uses a 5MP sensor (2592×1944) with adaptive face zooming and on-device facial detection powered by an ARTPEC-8 processor. It also supports 1D/2D QR code scanning as a credential modality, enabling touchless visitor verification without a back-end reader. Resolution is specified at 5MP; no minimum illumination figure or IR capability is listed in the provided specs.
The Hanwha TID-600R uses a 1/2.8" CMOS sensor at 1080P (2MP) with a maximum frame rate of 60fps. It includes an Auto ICR day/night mechanism, IR illumination to 0 lux (IR), and color sensitivity to 0.018 lux. WDR is rated at 150dB with SSDR and SSNR V noise reduction. At 25 pixels-per-meter (PPM), detection range is listed at 25.04m; recognition at 5.01m and identification at 2.50m per the DORI table.
The 03369-001 offers a higher-resolution sensor (5MP vs 2MP) better suited for face-capture use cases, plus on-device analytics. The TID-600R provides quantified low-light performance, IR capability, a 60fps frame rate, and a 150dB WDR rating — none of which are specified for the 03369-001.
How do the two units differ in audio, VoIP, and platform integration?
The 2N 03369-001 provides two-way audio (microphone and speaker) over H.264/H.265/MJPEG video streams. No SIP compatibility, VoIP protocol support, or specific PBX integration is listed in the provided specs for this unit. Integration context is limited to what the datasheet at /content/product-datasheets/03369-001.pdf may contain beyond the supplied fields.
The Hanwha TID-600R explicitly supports SIP 2.0 (RFC 3261 and companion RFCs) with documented compatibility for Cisco, Grandstream, Yealink, and Asterisk PBX systems. Audio streaming is two-way/one-way selectable in full duplex, with a built-in speaker rated at 85dB at 0.5m and audio compression via G.711 µ-law, G.726 ADPCM, and additional codecs. It supports ONVIF Profile S, SUNAPI (HTTP API), and Wisenet open platform for VMS integration.
For sites requiring direct SIP/PBX trunk integration or existing Wisenet/ONVIF VMS infrastructure, the TID-600R carries explicit, named compatibility. The 03369-001's integration ecosystem is not described in the provided specs beyond Ethernet/PoE+ connectivity.
Which unit is better suited for harsh outdoor environments and what are the installation power requirements?
The 2N 03369-001 requires PoE+ (802.3at) at approximately 15–18W (specified as ~18W in the power field). Its environmental rating is IP66 and IK10 per the supplied specs, making it resistant to high-pressure water jets and rated for significant mechanical impact. Wall-mount installation is specified. No operating temperature range is listed in the provided specs.
The Hanwha TID-600R accepts PoE (802.3af) or 12VDC and draws a maximum of 12.95W — compatible with standard 802.3af switches without requiring a PoE+ upgrade. Its certifications include IP65, IK08, NEMA4X, UL Safety, and FCC/CE EMC. Operating temperature is rated from -30°C to +55°C (-22°F to +131°F). Physical dimensions are 49×165×48mm and weight is 490g. A 3-year warranty is stated.
The 03369-001's IK10 rating provides one impact-resistance tier above the TID-600R's IK08, and IP66 exceeds the TID-600R's IP65 for water ingress. However, the TID-600R's 802.3af compatibility reduces switch infrastructure cost, its operating temperature range is fully documented, and its NEMA4X certification adds a recognized North American environmental standard not listed for the 03369-001.
Which should you choose: the 03369-001 or the TID-600R?
Our take: The 03369-001 is the stronger choice when on-device identity analytics — 5MP face capture with adaptive zooming and 1D/2D QR credential scanning — are the primary requirement, particularly in access-controlled lobbies or gates where touchless credential verification or high-resolution face images for audit logs are mandated. Key spec deltas: the 03369-001 resolves at 5MP (2592×1944) versus the TID-600R's 2MP 1080P; the 03369-001 carries IK10 versus IK08 and IP66 versus IP65; however, the TID-600R draws only 12.95W on standard 802.3af while the 03369-001 demands PoE+ at ~18W. The TID-600R is the better fit for SIP/VoIP-centric deployments — it natively trunks into Cisco, Asterisk, Grandstream, and Yealink PBX environments, provides documented IR performance to 0 lux, a 60fps frame rate, and a fully specified -30°C to +55°C operating range. No SIP capability or low-light specification is provided for the 03369-001 in the supplied data.
Side-by-Side Comparison
Spec-for-spec, from manufacturer data.
| Specification | 2N 03369-001 | Hanwha TID-600R |
|---|---|---|
| Product Type | Video Intercom (Outdoor) | Video Intercom (Outdoor) |
| Resolution | 5MP (2592×1944) | 1080P / 2MP |
| Sensor | — | 1/2.8" CMOS |
| Max Frame Rate | — | 60fps |
| Min. Illumination (Color) | — | 0.018 Lux |
| Min. Illumination (IR) | — | 0 Lux |
| IR Illumination | — | Yes, 5m |
| WDR | — | 150dB |
| On-Device Analytics | Facial detection, QR code (1D/2D), adaptive face zoom | Directional, Loitering, Enter/Exit, Virtual line, Audio/Shock detection |
| QR Code Scanning | Yes (1D/2D) | — |
| SIP / VoIP | — | SIP 2.0 (RFC 3261); Cisco, Asterisk, Grandstream, Yealink |
| Audio | Two-way (mic + speaker) | Two-way full duplex; built-in speaker 85dB @ 0.5m |
| Video Compression | H.265 / H.264 / MJPEG | H.265 / H.264 / MJPEG |
| Power Input | PoE+ (802.3at) | PoE (802.3af) or 12VDC |
| Max Power Draw | ~18W | 12.95W |
| IP / IK Rating | IP66 / IK10 | IP65 / IK08 |
| Operating Temperature | — | -30°C to +55°C |
| Edge Storage | — | microSD/SDHC/SDXC up to 256GB |
| ONVIF | — | ONVIF Profile S |
| Alarm I/O | — | 2 Inputs / 1 Output Relay |
| Certifications | IP66, IK10 | IP65, IK08, NEMA4X, UL, FCC, CE |
| Warranty | — | 3 years |
| Mount Type | Wall | Wall |
| Connectivity | Ethernet (Wired) | Ethernet (Wired) |
Frequently Asked Questions
Which should you choose: the 03369-001 or the TID-600R?
The 03369-001 is the stronger choice when on-device identity analytics — 5MP face capture with adaptive zooming and 1D/2D QR credential scanning — are the primary requirement, particularly in access-controlled lobbies or gates where touchless credential verification or high-resolution face images for audit logs are mandated. Key spec deltas: the 03369-001 resolves at 5MP (2592×1944) versus the TID-600R's 2MP 1080P; the 03369-001 carries IK10 versus IK08 and IP66 versus IP65; however, the TID-600R draws only 12.95W on standard 802.3af while the 03369-001 demands PoE+ at ~18W. The TID-600R is the better fit for SIP/VoIP-centric deployments — it natively trunks into Cisco, Asterisk, Grandstream, and Yealink PBX environments, provides documented IR performance to 0 lux, a 60fps frame rate, and a fully specified -30°C to +55°C operating range. No SIP capability or low-light specification is provided for the 03369-001 in the supplied data.
Can the TID-600R connect directly to our Cisco or Asterisk phone system?
Yes. The TID-600R specifies SIP 2.0 (RFC 3261) support with explicitly named compatibility for Cisco, Grandstream, Yealink, and Asterisk. No SIP or PBX integration capability is listed in the provided specs for the 03369-001.
Does the 03369-001 or TID-600R require a PoE+ switch, or will a standard PoE switch work?
The 03369-001 requires PoE+ (802.3at) at approximately 18W, so a PoE+ capable switch or injector is needed. The TID-600R operates on standard PoE (802.3af) at a maximum of 12.95W and also accepts 12VDC, making it compatible with a wider range of existing switch infrastructure.
Which unit is better for low-light or nighttime visitor identification at the door?
The TID-600R provides specified IR illumination to 0 lux (IR mode) and 0.018 lux color sensitivity, with Auto ICR day/night switching and 150dB WDR. No minimum illumination, IR capability, or low-light specification is listed in the provided specs for the 03369-001, so a direct low-light comparison cannot be made from the available data.
More Intercom Comparisons
- Hanwha TID-600R vs Aiphone IX-EA
- Hanwha TID-600R vs Axis A8207-VE
- Hanwha TID-600R vs Aiphone IX-DVF-6
- Hanwha TID-600R vs Aiphone JOS-1FW
- Aiphone IX-EA vs Axis A8207-VE
- Aiphone IX-EA vs 2N 01273-001
Intercom Buying Guides
Get a Second Opinion on Your Camera Choice
Share your site layout, coverage goals, and budget. Our team will validate the camera selection, flag anything we would change, and recommend products that match the use case.