Vivotek GET-083A-120 vs Axis D8004: Specification Comparison
Both the Vivotek AW-GET-083A-120 and the Axis D8004 are unmanaged 4-port PoE Gigabit Ethernet switches aimed at IP surveillance deployments. The Vivotek unit is a hardened outdoor appliance with a 120W PoE budget, dual SFP uplinks, and full environmental ruggedization. The Axis D8004 is a compact indoor unit with a 60W PoE budget and a single RJ45 uplink. Buyers choosing between them are typically weighing deployment environment, total power headroom, and uplink flexibility against form factor and cost of ownership.
In This Guide
- How do the PoE port count, per-port power, and total power budget compare?
- Which switch is rated for outdoor and extreme-environment installation?
- How do switching capacity, uplink options, and network management capabilities compare?
- Which should you choose: the GET-083A-120 or the D8004?
- Side-by-Side Specs
- FAQ
How do the PoE port count, per-port power, and total power budget compare?
Both switches provide four PoE-capable RJ45 ports rated at IEEE 802.3af/at. The Vivotek AW-GET-083A-120 delivers up to 30W per port with a total PoE budget of 120W, meaning all four ports can run simultaneously at full 30W without throttling. The Axis D8004 specifies a maximum total PoE output of 60W across four ports; per-port maximum is 30W (802.3at), but the 60W aggregate cap means simultaneous full-load on all four ports is not possible—at most two ports can run at 30W concurrently, or the load must be distributed below 15W per port to power all four.
On uplink capacity, the Vivotek provides two additional 10/100/1000 RJ45 ports and two 1G SFP slots, giving installers a choice of copper or fiber uplinks and the ability to daisy-chain or trunk. The Axis D8004 provides a single 10/100BASE-TX RJ45 uplink port. No SFP or fiber option is listed in the Axis specifications.
Which switch is rated for outdoor and extreme-environment installation?
The Vivotek AW-GET-083A-120 carries an IP67 ingress-protection rating (dust-tight, immersion-resistant) and an IK10 vandal-resistance rating. Its operating temperature range is -40°C to +65°C (-40°F to +149°F), and it has been tested to IEC 60068-2-6 (vibration), IEC 60068-2-27 (shock), and IEC 60068-2-32 (freefall). Surge protection is rated at 6 kV per PoE port and 40 kV on the AC power input (ITU-T K.21, IEC-61643-11). The enclosure accepts M16 and M25 conduit fittings and weighs 4.52 kg, consistent with a pole- or wall-mount outdoor cabinet. These specifications make it suitable for exposed outdoor installations.
The Axis D8004 is rated for indoor use only. Its operating temperature range is 0°C to 50°C (32°F to 122°F) and storage is -10°C to 50°C. No IP ingress rating, IK impact rating, or surge-protection figures are stated in the supplied specifications. The unit measures 90 × 80 × 21 mm and weighs 172 g, which is consistent with a desktop or surface-mount indoor device. Mounting brackets and feet are included accessories. Deploying the D8004 outdoors or in uncontrolled-temperature environments is outside its stated specification.
How do switching capacity, uplink options, and network management capabilities compare?
The Vivotek AW-GET-083A-120 has a switching bandwidth of 16 Gbps and a forwarding capacity of 11.904 Mpps, with an 8K MAC address table and support for 9216-byte jumbo frames. It supports auto-MDI/MDI-X and auto-negotiation on all ports. The two SFP slots allow fiber uplinks for longer cable runs between buildings or to a distribution switch, and the two additional copper GbE ports provide further flexibility.
The Axis D8004 specifications do not state switching bandwidth, forwarding rate, MAC table size, or jumbo frame support. Both units appear to be unmanaged (no SNMP, CLI, or web-GUI management is listed for either). The D8004's single copper uplink is adequate for a small cluster of cameras on the same LAN segment but does not offer fiber connectivity. For deployments requiring SFP uplinks, jumbo frames, or quantified switching throughput, only the Vivotek supplies those figures.
Which should you choose: the GET-083A-120 or the D8004?
Our take: The AW-GET-083A-120 is the stronger choice when cameras are deployed outdoors, in harsh environments, or where full 120W PoE headroom is required across all four ports. Three concrete spec deltas illustrate the gap: (1) total PoE budget is 120W vs. 60W—the Vivotek can power four 30W cameras simultaneously while the Axis cannot; (2) operating range is -40°C to +65°C vs. 0°C to +50°C, and the Vivotek adds IP67/IK10 and 6 kV per-port surge protection that the Axis does not list; (3) the Vivotek adds two SFP slots and two extra copper ports versus the Axis D8004's single copper uplink. The Axis D8004 is appropriate for a small, climate-controlled indoor installation—a server room IDF, a reception desk, or an interior wiring closet—where its compact 172 g form factor and 60W budget are sufficient and the lower complexity is an advantage.
Side-by-Side Comparison
Spec-for-spec, from manufacturer data.
| Specification | Vivotek GET-083A-120 | Axis D8004 |
|---|---|---|
| PoE Port Count | 4 × RJ45 PoE+ | 4 × RJ45 PoE |
| PoE Standard | IEEE 802.3af/at | IEEE 802.3af/at |
| Max. Power Per PoE Port | 30W | 30W (802.3at) |
| Total PoE Power Budget | 120W | 60W |
| Additional Uplink Ports | 2 × GbE RJ45 + 2 × 1G SFP | 1 × 10/100 RJ45 |
| Switching Bandwidth | 16 Gbps | Not specified |
| Forwarding Capacity | 11.904 Mpps | Not specified |
| MAC Address Table | 8K | Not specified |
| Jumbo Frame Support | 9216 bytes | Not specified |
| Environment Rating | Outdoor — IP67 / IK10 | Indoor only |
| Operating Temperature | -40°C to +65°C | 0°C to +50°C |
| Surge Protection (PoE Port) | 6 kV per port | Not specified |
| Surge Protection (AC Input) | 40 kV | Not specified |
| Power Input | 100–240VAC, 50–60Hz | 100–240VAC, 50–60Hz, 62W max |
| Dimensions (mm) | 315.4 × 245.8 × 118 | 90 × 80 × 21 |
| Weight | 4.52 kg | 172 g |
| Operating Humidity | 10–90% non-condensing | 5–95% non-condensing |
| Warranty | 24 months | 3 years |
| Regulatory Approvals | CE, FCC, VCCI, C-Tick Class A | CE, FCC Part 15 Class B, RoHS, WEEE |
Frequently Asked Questions
Which should you choose: the GET-083A-120 or the D8004?
The AW-GET-083A-120 is the stronger choice when cameras are deployed outdoors, in harsh environments, or where full 120W PoE headroom is required across all four ports. Three concrete spec deltas illustrate the gap: (1) total PoE budget is 120W vs. 60W—the Vivotek can power four 30W cameras simultaneously while the Axis cannot; (2) operating range is -40°C to +65°C vs. 0°C to +50°C, and the Vivotek adds IP67/IK10 and 6 kV per-port surge protection that the Axis does not list; (3) the Vivotek adds two SFP slots and two extra copper ports versus the Axis D8004's single copper uplink. The Axis D8004 is appropriate for a small, climate-controlled indoor installation—a server room IDF, a reception desk, or an interior wiring closet—where its compact 172 g form factor and 60W budget are sufficient and the lower complexity is an advantage.
Can the Axis D8004 power four 30W cameras at the same time?
No. The D8004's total PoE output is specified at a maximum of 60W across all four ports. Powering four cameras simultaneously at 30W each would require 120W, which exceeds that budget. The Vivotek AW-GET-083A-120 has a 120W budget and is rated for 30W per port across all four ports concurrently.
Is the Vivotek AW-GET-083A-120 suitable for pole-mount or exterior wall installation?
Yes, based on its specifications. It carries an IP67 rating (dust-tight and immersion-resistant), IK10 vandal resistance, an operating temperature range of -40°C to +65°C, 6 kV per-port surge protection, 40 kV AC-input surge protection, and M16/M25 conduit-entry fittings. The Axis D8004 is rated for indoor use only and lists no equivalent environmental or surge ratings.
Which switch offers more uplink flexibility for connecting to a distribution switch or NVR?
The Vivotek AW-GET-083A-120 provides two 1G SFP slots and two additional copper GbE ports as uplinks, supporting both fiber and copper connections to upstream equipment. The Axis D8004 provides a single 10/100BASE-TX copper uplink. No SFP or fiber option is listed for the D8004. For fiber runs or redundant uplinks, only the Vivotek supplies those options based on the provided specifications.
More Network Switch Comparisons
- Vivotek GET-083A-120 vs TP-Link SG1005P
- Vivotek GET-083A-120 vs Axis T8504-E
- Vivotek GET-083A-120 vs Ubiquiti N-SW
- TP-Link SG1005P vs Axis T8504-E
- TP-Link SG1005P vs Axis D8004
- TP-Link SG1005P vs Ubiquiti N-SW
Network Switch Buying Guides
Get a Second Opinion on Your Camera Choice
Share your site layout, coverage goals, and budget. Our team will validate the camera selection, flag anything we would change, and recommend products that match the use case.