Installation Hardware & Kits
Sub categories
Showing Results for Installation Hardware & Kits
-
Digital Watchdog
SKU: DWC-EXTIR100
Digital Watchdog DWC-EXTIR100 100ft IR Illuminator
- 100-foot IR illuminator for extended low-light detection
- External pole or surface mounting independent of camera
- Extends single-camera IR coverage with strategic placement
$300.00 $194.99 Save $105.01The item has been added -
Add to Cart The item has been addedELK Products
SKU: ELK-91212
ELK Products ELK-91212 SPDT Relay Module 12VDC
12VDC SPDT relay module for door strike and magnetic lock control
- SPDT relay module switches one strike NO or NC on the same coil
- 12VDC operation for fail-safe and fail-secure door strike control
- Drops into ELK M1 Gold panel for one-relay door logic switching
$129.99The item has been added -
Add to Cart The item has been addedELK Products
SKU: ELK-912B6
ELK Products ELK-912B6 SPDT Relay Module 12VDC
12VDC SPDT relay module for access control and alarm routing
- SPDT relay module routes one signal to either of two circuits
- 12VDC coil drives door strike, alarm, or automation logic switching
- Compact relay PCB for in-cabinet ELK panel integration
$108.99The item has been added -
ELK Products
SKU: ELK-M1TWS
ELK Products ELK-M1TWS Two Way Speaker Microphone
Two-way speaker microphone for ELK M1 security panels
- Two-way speaker plus microphone for full-duplex panel voice
- Operators can listen and speak without switching modes
- Direct ELK M1 panel integration over standard audio wiring
$50.99The item has been added -
Add to Cart The item has been addedELK Products
SKU: ELK-M1RB
ELK Products M1 Relay Board M1Rb - ELK-M1RB
- M1 relay output expansion adds switched loads to ELK panels
- Drives extra door strikes, maglocks, fans, lights, or sirens
- Direct M1 panel integration - no external gateway needed
$173.99The item has been added -
Epson
SKU: BOX-T88II
Epson BOX-T88II Receipt Printer Accessory Kit
Wi-Fi receipt printer box kit for T88II, T88III, T88IV models
- OEM packaging box for T88II/T88III/T88IV receipt printers
- Wi-Fi-equipped unit at 500 mm/s print speed
- Replacement protective box across mixed POS environments
$19.30 $18.99 Save $0.31The item has been added -
Epson
SKU: CEPS-BEEPER
Epson CEPS-BEEPER Coupler with Beeper RJ-11 Cable
RJ-11 coupler with beeper audio feedback for Epson POS printers
- RJ-11 coupler with integrated beeper for POS signaling
- Audible alert accessory for receipt printer events
- 0.1 lb cable accessory for retail POS use
$42.80 $41.99 Save $0.81The item has been added -
FLIR
SKU: 324-0004-00
FLIR Hard Case w/foam - 324-0004-00
- Hard-shell transport case with FLIR-specific foam cutouts
- Lockable latches prevent in-transit opening during shipping
- High-impact polymer protects thermal optics from drops
$2,049.00 $1,497.99 Save $551.01The item has been added -
FLIR
SKU: CM-CAPX-G4F
FLIR Pendant Cap Kit for CM-6412 Hemispheric Cameras - CM-CAPX-G4F
- Pendant cap kit for CM-6412 hemispheric cameras
- Adapts hemispheric cameras to conduit-mounted pendant installs
- Maintains environmental sealing during overhead deployment
$114.00 $113.99 Save $0.01The item has been added -
FLIR
SKU: 324-0005-00
FLIR PT-Series Hard Case w/foam - 324-0005-00
- Hard transport case for FLIR PT-Series cameras
- Custom foam inserts cradle PT-Series thermal optics
- Lockable latches prevent in-transit case opening
$2,089.00 $1,526.99 Save $562.01The item has been added -
Geovision
SKU: 240-POSTS-002
Geovision 240-POSTS-002 POS Text Sender Dongle 2 Ports
- Dual POSINT ports support multiple POS terminals without additional interface hardware.
- Native Geovision integration eliminates middleware, reducing deployment time and support overhead.
- Real-time transaction-to-video sync enables precise forensic review of voids, refunds, and sales.
$200.00 $199.99 Save $0.01The item has been added -
Geovision
SKU: 46-DE21620-0001
Geovision 46-DE21620-0001 Accessory
Geovision accessory component for NVR system integration and deployment
- Integrates with compatible Geovision cameras, NVRs, and management software.
- Compact 7×6×1 in form factor fits standard rack and enclosure mounting layouts.
- 3-year warranty provides long-term coverage for professional deployments.
$20.99The item has been added -
Geovision
SKU: 54-BXWIUSB-MP02
Geovision 54-Bxwiusb-MP02 Gv-Wifi Adapter V2
- Adds WiFi connectivity to supported Geovision IP PTZ cameras via direct integration.
- Eliminates hardwired Ethernet runs where cable routing is impractical or restricted.
- V2 generation module delivers updated compatibility with select Geovision PTZ platforms.
$58.00 $57.99 Save $0.01The item has been added -
Geovision
SKU: 55-CTRLC-000
Geovision 55-CTRLC-000 Control Center Dongle
- Integrates directly with Geovision Control Center software via USB—no third-party drivers needed.
- CM-rated cable meets indoor flame safety requirements for commercial and residential deployments.
- Plug-and-play USB connectivity reduces setup time on Windows-based Geovision NVR/DVR systems.
$600.00 $355.99 Save $244.01The item has been added -
Geovision
SKU: 55-GS001-000
Geovision 55-GS001-000 GV-GIS Mobile Connection
- Native GV-GIS integration eliminates custom gateway config on existing deployments.
- iOS and Android support enables live view and event playback from any field location.
- Role-based access control syncs with GV-GIS accounts, avoiding duplicate credential setup.
$60.00 $59.99 Save $0.01The item has been added -
Geovision
SKU: 55-POSTS-002
Geovision 55-POSTS-002 GV-POS Text Inserter Dongle 2 Ports
- Dual POSINT ports enable simultaneous overlay from two independent POS terminals.
- Real-time text insertion embeds transaction data natively—no post-processing required.
- Timestamp sync aligns POS events to video frames, simplifying dispute and audit workflows.
$200.00 $199.99 Save $0.01The item has been added
Installation Hardware & Kits
Installation hardware and kits provide the job-ready components needed to mount, secure, and complete commercial surveillance, access control, and intercom deployments. Standardizing installation parts helps speed up installs and supports consistent long-term serviceability.
Plan Your Deployment
- Mounting surface type and hardware compatibility
- Indoor vs outdoor durability requirements
- Standardization across sites and install teams
- Serviceability and replacement part planning
- Project staging and kit-based installation efficiency
Installation Hardware & Kits — Engineering-Grade Installation Accessories for Commercial Deployments
This category covers 48 working models of installation hardware & kits sourced manufacturer-direct or through channel-direct US distribution. Build the rest of your system around the architectural choices below — compatibility, environmental rating, and lifecycle decisions made here propagate through every downstream component you specify.
What to Look For
Compatibility comes first. Mounting brackets, housings, and adapters are specific to the camera or device they support — the same manufacturer often makes parallel lines that don't share accessories. Verify the part number against the camera/device datasheet or compatibility list before ordering. Installation labor consumed troubleshooting a mismatched mount is the most common rework on commercial jobs.
Environmental rating determines material and finish. Indoor accessories typically use steel or aluminum with a powder-coat finish; outdoor accessories need stainless steel or specifically-rated coastal-grade finishes for salt-air resistance. UV exposure degrades plastic over years; choose UV-stabilized polymers or metal for sun-exposed installs. Plan for replacement at year 7-10 on outdoor plastic accessories.
Mounting load capacity must exceed device weight by a healthy margin. Camera weight, housing weight, and any wind loading on PTZs combine. Wall, ceiling, and pole mounts each have rated maximum loads — check before specifying. Pole-mount and pendant-mount installations need conduit, junction boxes, and weather-sealing that aren't always specified in the camera kit.
Wire management and accessibility for service get overlooked in early planning. Bottom-loaded cable entry in housings, swing-out mounting plates, and accessible junction boxes save hours when a camera needs service. Cheap mounts that require complete dismount to access cables drive labor cost up at every service call. Specify service-friendly mounting hardware on installs you expect to service for 10+ years.
Key Specs in This Category
| Spec | Available Options |
|---|---|
| Resolution | 5MP, 20MP+, 2MP, 8MP |
| IP Rating | IP68, IP56 |
| Connectivity | Wired |
| Power | PoE |
| Type | Controller, Station Adaptors, LED Beacon/Strobe, Custom/Special Order Unit, Accessories, Lock/Strike, Relays and Control Units |
| Night Vision | Yes |
Top Brands in This Category
Frequently Asked Questions
Will this mount work with my camera?
Mounts are camera-specific in most cases. The product description and manufacturer's compatibility list are the authoritative source. If you're not certain, send the camera model and the mount part number to our Senior Specialists; we'll confirm compatibility before you order. Returning a mismatched mount after installation labor is significantly more expensive than checking up front.
Do I need a junction box?
For most outdoor and exposed-conduit camera installs, yes — junction boxes house cable terminations and protect splices from weather. The camera's mounting requirements often specify the junction-box size and material. Some camera-and-mount combinations integrate the junction box into the mount; others require a separate box. Confirm before ordering to avoid pulling cable into an installation that can't accept it.
What's the difference between a wall mount and a pendant mount?
Wall mounts attach to vertical surfaces and project the camera outward. Pendant mounts attach to ceilings or overhead structures and suspend the camera below. Pole mounts are a specialized wall mount for poles. Choose by the mounting surface available and the field-of-view orientation required; many cameras work in any mount with the right adapter.
Are stainless steel mounts worth the extra cost?
For outdoor coastal installs (within ~5 miles of saltwater), yes — galvanized steel rusts visibly within 2-3 years in coastal air. For inland outdoor, marine-grade is overkill; powder-coated galvanized lasts 10+ years. For corrosive industrial environments (chemical plants, wastewater), stainless steel or specifically-rated coatings extend service life dramatically. Match the material to the environment, not the budget pressure.
Can I use one brand's mount with another brand's camera?
Sometimes — many mounts accept standard mounting patterns (¼-20 thread, M6 pattern, VESA spacing) and cross brands. Manufacturer-specific cast housings rarely do. Check the mount's hole pattern and weight rating against the camera's specs. When in doubt, use the camera manufacturer's recommended mount; cross-brand savings on mounts are typically small and the warranty implications of mismatched hardware aren't worth the risk.
Need help choosing? Talk to a Senior Specialist — direct line 877-277-7147 or request a quote.