Retrofit Kits
Showing Results for Retrofit Kits
-
Add to Cart The item has been addedAxis
SKU: 02655-001
Axis Q6100-E Solo Installation Kit - 02655-001
IP66/IP67 weatherproof RJ45 connector kit for Axis Q6100-E solo setups
- IP66/IP67-rated push-pull connector handles jet spray and brief submersion
- Thermoplastic cover lid protects from UV degradation in outdoor installations
- Complete kit includes connector, plug, cover lid, and installation guide
In stock · Ships same business day$105.00 $100.99 Save $4.01The item has been added -
Axis
SKU: 5505-341
Axis 5505-341 T92E Camera Change Kit
- Camera change kit for swapping into existing AXIS T92E enclosures
- Maintains existing mount geometry and power supply during model swap
- Wall, ceiling, pole, or pendant mount - 5-year warranty included
$52.00 $51.99 Save $0.01The item has been added -
Code Blue
SKU: SLNP0133
Code Blue SLNP0133 Premium Solar Retrofit Kit
- Retrofit solar power into existing Code Blue installations without replacing hardware.
- Supports 12–24V DC operation, accommodating varied system power configurations.
- Classified as an expansion module, enabling independent off-grid uptime for security systems.
$6,466.99The item has been added -
Comelit
SKU: 909021753
Comelit 909021753 Readykey Controller Retrofit Kit
PoE+ retrofit controller for Comelit access control & ONVIF systems
- PoE+ (802.3at) power eliminates separate power runs, simplifying mixed upgrades.
- Bridges legacy Comelit readers to IP architecture without replacing installed hardware.
- ONVIF compliance ensures integration with standard-based VMS platforms out of the box.
$141.61 $140.99 Save $0.62The item has been added -
HES
SKU: 1500-106-630
HES 1500-106-630 Retrofit Kit
HES 1500 Series retrofit kit for field upgrades without system replacement
- Integrates directly with HES 1500 series strikes, eliminating cross-platform re-engineering.
- Runs on 24VDC input, fitting standard door control wiring without custom cabling.
- Field-deployable retrofit kit lets you upgrade existing doors without full system replacement.
$51.00 $50.99 Save $0.01The item has been added -
HES
SKU: 1500-106-BSP
HES 1500-106-BSP Retrofit Kit for 1500-BSP
24VDC electric strike retrofit kit for 1500-BSP maintenance and upgrades
- Designed for 1500-BSP compatibility, eliminates need for full system replacement
- Standardized installation workflows reduce labor time and deployment downtime
- Supports preventative maintenance, compliance updates, and component replacement
$102.00 $101.99 Save $0.01The item has been added -
Pelco
SKU: OHOVPOEIPM
Pelco OHOVPOEIPM PoE IPM Retrofit Kit
PoE retrofit for HOV housings—single-cable power, no external supply
- Integrates camera, heater, and blower power through PoE+ (802.3at)
- Converts existing HOV series housings to network-powered operation
- IP66/IP67 rated outdoor housing with IK10 impact resistance
$222.78 $221.99 Save $0.79The item has been added
Retrofit Kits
Retrofit kits provide mounting and adaptation solutions for upgrading existing surveillance and access control installations. These kits help align new device footprints with legacy mounting surfaces while maintaining structural integrity and a professional finish.
Plan Your Deployment
- Legacy mounting pattern compatibility
- Surface condition and structural support evaluation
- Indoor vs outdoor environmental requirements
- Device upgrade alignment and footprint adaptation
- Future scalability and replacement planning
Retrofit Kits — Engineering-Grade Installation Accessories for Commercial Deployments
This category covers 1 working models of retrofit kits sourced manufacturer-direct or through channel-direct US distribution. Build the rest of your system around the architectural choices below — compatibility, environmental rating, and lifecycle decisions made here propagate through every downstream component you specify.
What to Look For
Compatibility comes first. Mounting brackets, housings, and adapters are specific to the camera or device they support — the same manufacturer often makes parallel lines that don't share accessories. Verify the part number against the camera/device datasheet or compatibility list before ordering. Installation labor consumed troubleshooting a mismatched mount is the most common rework on commercial jobs.
Environmental rating determines material and finish. Indoor accessories typically use steel or aluminum with a powder-coat finish; outdoor accessories need stainless steel or specifically-rated coastal-grade finishes for salt-air resistance. UV exposure degrades plastic over years; choose UV-stabilized polymers or metal for sun-exposed installs. Plan for replacement at year 7-10 on outdoor plastic accessories.
Mounting load capacity must exceed device weight by a healthy margin. Camera weight, housing weight, and any wind loading on PTZs combine. Wall, ceiling, and pole mounts each have rated maximum loads — check before specifying. Pole-mount and pendant-mount installations need conduit, junction boxes, and weather-sealing that aren't always specified in the camera kit.
Wire management and accessibility for service get overlooked in early planning. Bottom-loaded cable entry in housings, swing-out mounting plates, and accessible junction boxes save hours when a camera needs service. Cheap mounts that require complete dismount to access cables drive labor cost up at every service call. Specify service-friendly mounting hardware on installs you expect to service for 10+ years.
Key Specs in This Category
| Spec | Available Options |
|---|---|
| IP Rating | IP66 |
| Type | Accessory |
Top Brands in This Category
Frequently Asked Questions
Will this mount work with my camera?
Mounts are camera-specific in most cases. The product description and manufacturer's compatibility list are the authoritative source. If you're not certain, send the camera model and the mount part number to our Senior Specialists; we'll confirm compatibility before you order. Returning a mismatched mount after installation labor is significantly more expensive than checking up front.
Do I need a junction box?
For most outdoor and exposed-conduit camera installs, yes — junction boxes house cable terminations and protect splices from weather. The camera's mounting requirements often specify the junction-box size and material. Some camera-and-mount combinations integrate the junction box into the mount; others require a separate box. Confirm before ordering to avoid pulling cable into an installation that can't accept it.
What's the difference between a wall mount and a pendant mount?
Wall mounts attach to vertical surfaces and project the camera outward. Pendant mounts attach to ceilings or overhead structures and suspend the camera below. Pole mounts are a specialized wall mount for poles. Choose by the mounting surface available and the field-of-view orientation required; many cameras work in any mount with the right adapter.
Are stainless steel mounts worth the extra cost?
For outdoor coastal installs (within ~5 miles of saltwater), yes — galvanized steel rusts visibly within 2-3 years in coastal air. For inland outdoor, marine-grade is overkill; powder-coated galvanized lasts 10+ years. For corrosive industrial environments (chemical plants, wastewater), stainless steel or specifically-rated coatings extend service life dramatically. Match the material to the environment, not the budget pressure.
Can I use one brand's mount with another brand's camera?
Sometimes — many mounts accept standard mounting patterns (¼-20 thread, M6 pattern, VESA spacing) and cross brands. Manufacturer-specific cast housings rarely do. Check the mount's hole pattern and weight rating against the camera's specs. When in doubt, use the camera manufacturer's recommended mount; cross-brand savings on mounts are typically small and the warranty implications of mismatched hardware aren't worth the risk.
Need help choosing? Talk to a Senior Specialist — direct line 877-277-7147 or request a quote.