Screw & Nut Kits
Showing Results for Screw & Nut Kits
-
Add to Cart The item has been addedAxis
SKU: 5901-391
Axis P55-E Screw Kit for Wall Mounts - 5901-391
Bayonet screw kit for P55-E PTZ cameras on T91G61/T91L61 mounts
- Quick-connect bayonet screws with securing locks prevent vibration loosening
- Three springs dampen thermal cycles and mechanical fatigue during pan-tilt duty
- Precision-fit hardware for P55-E Series eliminates over-tightening risk
In stock · Ships same business day$41.00 $40.99 Save $0.01The item has been added -
Axis
SKU: 01512-001
Axis 3/4" Conduit Locknut A 4-Pack - 01512-001
3/4" conduit locknuts (4-pack) for ceiling mount installations
- Four locknuts per pack sized for 3/4" conduit fastening
- Compatible with AXIS T91B53 Telescopic Ceiling Mount systems
- Precision-engineered for secure conduit anchoring in surveillance setups
$31.00 $29.99 Save $1.01The item has been added -
Hanwha
SKU: Z6003013801A
Hanwha Screw Taptite - Z6003013801A
- OEM taptite screw for Hanwha camera housings
- Thread-forming design eliminates pre-tapping in metal
- Reduces install time for camera service workflows
$0.99The item has been added -
HES
SKU: JN-50
HES JN-50 Jack Nuts and Flat Head Fastener Kit
100-piece M5 jack nuts and flat head fasteners for HES strike systems
- 50x M5 jack nuts paired with 50x M5 x .75 flat head fasteners
- Flat head profile sits flush in enclosures, brackets, and control panels
- Metric M5 sizing compatible with HES electric strikes and universal mounts
$99.00 $98.99 Save $0.01The item has been added -
Pelco
SKU: OPTACWBS_FLIR
Pelco OPTACWBS_FLIR Screw Kit PTACWBSQ2B Bracket
OEM fastener kit for PTACWBSQ2B FLIR thermal brackets
- Precision-matched thread pitch and corrosion-resistant material for secure mounting
- Includes torque specifications aligned with Pelco bracket installation standards
- Engineered exclusively for PTACWBSQ2B to prevent thread damage and galvanic corrosion
$10.00 $6.99 Save $3.01The item has been added -
STI
SKU: EPSNK
STI EPSNK EnviroArmour® Slot Nut Kit
- Mechanically couples STI strike assemblies to standard door frame slot configurations.
- Engineered for 9VDC STI lock and strike platforms for reliable electronic access control.
- Installation requires a 7mm masonry bit; gasket seals protect wiring from water ingress.
$53.99The item has been added -
STI
SKU: KIT-6702
STI KIT-6702 Tamperproof Screw Kit
- Prevents unauthorized fastener removal on STI lock and strike hardware installations.
- Compatible with HID credential-based access control infrastructure at 9VDC.
- Drop-in replacement for standard fasteners; no special tools required.
$9.99The item has been added -
TSC
SKU: 37-1502510-34LF
TSC 37-1502510-34LF M2.5x10 Replacement Screw Set
OEM M2.5x10 steel screws for TSC TPP-2410M thermal printer
- Two-piece set of M2.5x10 metric machine screws for TPP-2410M
- Steel fasteners rated to TSC OEM specs for print mechanisms
- Secure media guides, sensor brackets, and cover assemblies
$1.00 $0.99 Save $0.01The item has been added -
Zebra
SKU: P1112750-081
Zebra P1112750-081 Peel Bracket Mounting Screw Kit
Mounting screw kit for Zebra ZE511 Peel Bracket assembly
- Provides all screws needed to securely mount the Peel Bracket on ZE511 print engines.
- Eliminates sourcing delays by delivering the exact fastener set for bracket installation.
- Backed by a 1-year warranty, supporting reliable field replacements and depot repairs.
$28.68 $27.99 Save $0.69The item has been added
Screw & Nut Kits
Screw and nut kits provide essential fastening components for surveillance, intercom, and access control installations. Proper hardware selection supports secure mounting, structural stability, and long-term reliability in commercial environments.
Plan Your Deployment
- Material compatibility and corrosion resistance
- Load requirements and structural support needs
- Indoor vs outdoor durability considerations
- Standardization across multi-site projects
- Future maintenance and hardware replacement planning
Screw & Nut Kits — Engineering-Grade Installation Accessories for Commercial Deployments
This category covers 2 working models of screw & nut kits sourced manufacturer-direct or through channel-direct US distribution. Build the rest of your system around the architectural choices below — compatibility, environmental rating, and lifecycle decisions made here propagate through every downstream component you specify.
What to Look For
Compatibility comes first. Mounting brackets, housings, and adapters are specific to the camera or device they support — the same manufacturer often makes parallel lines that don't share accessories. Verify the part number against the camera/device datasheet or compatibility list before ordering. Installation labor consumed troubleshooting a mismatched mount is the most common rework on commercial jobs.
Environmental rating determines material and finish. Indoor accessories typically use steel or aluminum with a powder-coat finish; outdoor accessories need stainless steel or specifically-rated coastal-grade finishes for salt-air resistance. UV exposure degrades plastic over years; choose UV-stabilized polymers or metal for sun-exposed installs. Plan for replacement at year 7-10 on outdoor plastic accessories.
Mounting load capacity must exceed device weight by a healthy margin. Camera weight, housing weight, and any wind loading on PTZs combine. Wall, ceiling, and pole mounts each have rated maximum loads — check before specifying. Pole-mount and pendant-mount installations need conduit, junction boxes, and weather-sealing that aren't always specified in the camera kit.
Wire management and accessibility for service get overlooked in early planning. Bottom-loaded cable entry in housings, swing-out mounting plates, and accessible junction boxes save hours when a camera needs service. Cheap mounts that require complete dismount to access cables drive labor cost up at every service call. Specify service-friendly mounting hardware on installs you expect to service for 10+ years.
Key Specs in This Category
| Spec | Available Options |
|---|---|
| Type | Accessory |
Top Brands in This Category
Frequently Asked Questions
Will this mount work with my camera?
Mounts are camera-specific in most cases. The product description and manufacturer's compatibility list are the authoritative source. If you're not certain, send the camera model and the mount part number to our Senior Specialists; we'll confirm compatibility before you order. Returning a mismatched mount after installation labor is significantly more expensive than checking up front.
Do I need a junction box?
For most outdoor and exposed-conduit camera installs, yes — junction boxes house cable terminations and protect splices from weather. The camera's mounting requirements often specify the junction-box size and material. Some camera-and-mount combinations integrate the junction box into the mount; others require a separate box. Confirm before ordering to avoid pulling cable into an installation that can't accept it.
What's the difference between a wall mount and a pendant mount?
Wall mounts attach to vertical surfaces and project the camera outward. Pendant mounts attach to ceilings or overhead structures and suspend the camera below. Pole mounts are a specialized wall mount for poles. Choose by the mounting surface available and the field-of-view orientation required; many cameras work in any mount with the right adapter.
Are stainless steel mounts worth the extra cost?
For outdoor coastal installs (within ~5 miles of saltwater), yes — galvanized steel rusts visibly within 2-3 years in coastal air. For inland outdoor, marine-grade is overkill; powder-coated galvanized lasts 10+ years. For corrosive industrial environments (chemical plants, wastewater), stainless steel or specifically-rated coatings extend service life dramatically. Match the material to the environment, not the budget pressure.
Can I use one brand's mount with another brand's camera?
Sometimes — many mounts accept standard mounting patterns (¼-20 thread, M6 pattern, VESA spacing) and cross brands. Manufacturer-specific cast housings rarely do. Check the mount's hole pattern and weight rating against the camera's specs. When in doubt, use the camera manufacturer's recommended mount; cross-brand savings on mounts are typically small and the warranty implications of mismatched hardware aren't worth the risk.
Need help choosing? Talk to a Senior Specialist — direct line 877-277-7147 or request a quote.