DMP

SKU: 716T

DMP 716T Plug-In Screw Terminal Module

Plug-in screw terminal module for DMP system expansion slots

• Replaces the standard DMP 716 harness with individual screw terminals for field wiring.
• Plug-in connector seats directly into the 716 Output Expansion Module socket—no adapters needed.
• Accepts 18–22 AWG stranded wire, suitable for alarm loops, relay contacts, and 12VDC returns.

DMP

SKU: 718T

DMP 718T Plug-In Screw Terminal Module

Plug-in screw terminal module for DMP expansion platforms

• Captive screw terminals eliminate soldering, cutting field termination time during installs.
• Plug-in design fits standard DMP expansion slots, enabling I/O scaling without chassis replacement.
• Compact 4.50×2.75×1.75 in form factor supports wall-mount deployment in tight panel enclosures.

DMP

SKU: 719T

DMP 719T Terminal Board Expansion Module

Modular terminal board expansion for DMP systems with plug-in slots

• Extends DMP 714 Zone Expander wiring capacity via direct plug-in — no adapters needed.
• Accepts 14–22 AWG wire with individual 1K EOL resistors for supervised zone circuits.
• Integrated LX-Bus pass-through eliminates external terminal blocks and junction boxes.

DMP

SKU: 721T

DMP 721T Terminal Block Module

TCP/IP terminal block module for multi-door access control expansion

• Consolidates zone wiring for DMP XR series panels in a compact box-form module.
• Accepts 14–22 AWG conductors, covering standard sensor and detector loop gauges.
• Pre-installed per-zone EOL resistors eliminate discrete end-of-line components in field.

DMP

SKU: 736P

DMP 736P Radionics POPIT Interface Module

• Interfaces DMP systems with Radionics POPIT devices for cross-platform integration.
• Expansion module form factor simplifies addition to existing DMP control panel installations.
• Datasheet available for download to support pre-deployment planning and compliance review.

DMP

SKU: 738A

DMP 738A Interface Expansion Module

TCP/IP expansion module for DMP control panels with 12VDC operation

• TCP/IP communication eliminates proprietary serial links for clean network integration.
• Draws 12VDC from existing panel supply rail—no separate regulated power source needed.
• Slot-based form factor (5.5"×3"×0.75") minimizes panel footprint versus stand-alone boxes.

DMP

SKU: 7463-W

DMP 7463-W Network Thinline LCD Keypad with Prox Reader

Network LCD keypad with dual PIN and proximity card access

• Network communication eliminates dedicated wiring runs, simplifying multi-keypad deployments.
• Integrated proximity reader supports dual-credential (PIN + prox card) access from one device.
• Built-in 4-hour backup battery maintains operation during AC loss without an external enclosure.

DMP

SKU: 763

DMP 763 Wi-Fi Interface Module

Wi-Fi interface for DMP keypad systems—wireless retrofit or new build

• Adds 2.4GHz Wi-Fi to DMP XT/XR panels—no network cable run required.
• Auto-fails over to cellular if Wi-Fi drops, maintaining signal path continuity.
• Draws 12VDC directly from panel supply; no external power adapter needed.

DMP

SKU: 861

DMP 861 Power Distribution/4 Wire Bus Module

Centralized power & 4-wire bus module for multi-keypad access systems

• 4-wire bus connectivity synchronizes multiple keypads and readers from one module.
• Centralized 12V/24V DC power distribution eliminates distributed point-of-load supplies.
• Compact form factor mounts in existing DMP cabinets with no separate power supply needed.

DMP

SKU: 865

DMP 865 Style W/X Notification Module

TCP/IP notification module for DMP control panel auxiliary expansion

• TCP/IP integration eliminates dedicated serial runs in DMP control panel networks.
• Monitors opens, shorts, and ground faults on notification circuits in real time.
• Operates at 9.6–14.2 VDC, compatible with panel-mounted or remote 24VDC supplies.

DMP

SKU: 866

DMP 866 Notification Module

12VDC auxiliary notification module for DMP access control expansion

• Runs on 12VDC, integrating directly into existing access control cabinet power supplies.
• Auxiliary architecture adds notification endpoints without disrupting active panel configs.
• Scales multi-door and multi-reader deployments without replacing core control infrastructure.

DMP

SKU: 867

DMP 867 LX-Bus Addressable Notification Module

LX-Bus addressable notification module for networked multi-site control

• Style W supervised circuit supports 12VDC or 24VDC notification loads on one module.
• Built-in ground fault, open, and short detection with four status LEDs prevents silent failures.
• LX-Bus TCP/IP backbone enables centralized notification control across distributed multi-site deployments.

DMP

SKU: 869

DMP 869 Style D Initiating Module

25VDC initiating module expands DMP security system zones

• Two independent supervised 4-wire initiating circuits expand DMP panel zone capacity.
• 8–25 VDC operating range integrates directly with standard DMP power distribution.
• Continuous ground-fault supervision detects wiring opens, shorts, and faults pre-alarm.

DMP

SKU: 893A

DMP 893A Dual Phone Line Module Keypad

Dual phone line keypad module for DMP access control expansion

• Monitors main and backup phone lines for voltage drops, alerting local keypads and central station.
• UL 864 listed and FCC Part 15/68 compliant, meeting fire signaling and telecom regulatory requirements.
• Installs into DMP panel enclosure at 12VDC via wire harness, fitting existing auxiliary expansion slots.

DMP

SKU: AP2-20N

DMP AP2-20N Curtain PIR Motion Detector

Curtain PIR motion detector for doorways, windows, and perimeter zones

• Vertical curtain pattern limits coverage to doorways and windows, cutting lateral false alarms.
• Hardwired zone-loop connection eliminates battery maintenance and wireless mesh overhead.
• Native DMP panel integration supports unified hardwired architecture with contacts and keypads.

DMP

SKU: CM-30E

DMP CM-30E Push to Exit Button

24VDC networked push-to-exit button for DMP access control

• Accepts 12 or 24 VDC supply, matching either DMP XT or XR Series panel output.
• SPDT contacts support NO or NC wiring to meet your panel's fail-safe configuration.
• Single-gang stainless faceplate fits standard electrical boxes; consumes one zone input.