Lifesafety Power · FPO250/250-4C8P4D8PE12S

Lifesafety Power FPO250/250-4C8P4D8PE12S Power Systems 500W Dual

500W dual-voltage power supply designed for mid-to-large access control installations, combining primary power distribution with battery backup and

• 500W dual 12V/24V output supports up to 64 controlled loads in one UL-listed enclosure.
• 32 relay outputs (4×C8P) programmable failsafe or failsecure at 2.5A per zone, no external relays needed.
• 32 auxiliary outputs (4×D8P) power sensors and REX devices with per-zone dual-buss voltage selection.

Lifesafety Power · FPO250/250-4D84M8NLCE12S

Lifesafety Power FPO250/250-4D84M8NLCE12S 250W power supply 20A

250W managed power distribution module designed for multi-camera and networked security deployments where selective voltage output and per-port

• Selectable primary output—12VDC/20A or 24VDC/10A—integrates mixed-voltage devices on one supply.
• Eight independently fused 3A DC auxiliary outputs isolate faults without taking down the full system.
• Per-port Bus1/Bus2 assignment lets you segment cameras, readers, and alarms on separate protected rails.

Lifesafety Power · FPO250/250-4D8PE2

Lifesafety Power FPO250/250-4D8PE2 2 x 250W power supply 8 relay

Dual-channel power supply designed to deliver redundant DC power to networked security systems across distributed installations

• Two independent 250W channels, each selectable 12VDC/20A or 24VDC/10A, support mixed fleets.
• Four Class 2 auxiliary outputs at 2.5A each isolate sensor and access control loads from camera power.
• Per-output Bus1/Bus2 assignment partitions zones across separate supervision circuits without extra relays.

Lifesafety Power · FPO250/250-4M8PNLCSD16E4

Lifesafety Power FPO250/250-4M8PNLCSD16E4 250W power supply 20A

250W managed power distribution system designed for multi-camera and access-control installations where circuit-level protection and output isolation

• 250W capacity supports 8–12 full-power IP cameras or access readers without undersizing.
• Eight individually supervised 2.5A outputs isolate faults so one short won't kill the system.
• Selectable 12VDC/24VDC output covers both legacy analog and modern IP devices on one supply.

Lifesafety Power · FPO250/250-5D8P3M8NLCE12M/P24-A

Lifesafety Power FPO250/250-5D8P3M8NLCE12M/P24-A Mercury ProWire

500W dual-voltage power distribution system designed for access control and security infrastructure

• 500W dual-voltage output supports locks, readers, and ancillary devices in one unit.
• 24 managed lock outputs enable power sequencing and load-shedding across multi-door deployments.
• 40 auxiliary outputs eliminate individual UPS modules, centralizing power for up to 40 circuits.

Lifesafety Power · FPO250/250-5D8P3M8PNLCE12M/P24-B

Lifesafety Power FPO250/250-5D8P3M8PNLCE12M/P24-B 250W power supp

250W managed power distribution module engineered for multi-zone access control installations where legacy 12V readers and modern 24V hardware must

• 250W capacity supports 20A @ 12V or 10A @ 24V across one module.
• Eight Class 2 outputs at 2.5A each keep door hardware UL-compliant.
• Dual-bus architecture enables zone segregation without extra feeder runs.

Lifesafety Power · FPO250/250-B10010D8NLCE8M2

Lifesafety Power FPO250/250-B10010D8NLCE8M2 250W power supply

250W power supply with dual selectable outputs—20A at 12VDC or 10A at 24VDC

• Dual-bus outputs deliver 12VDC@20A or 24VDC@10A from one cabinet.
• Eight 3A auxiliary outputs each assign independently to Bus 1 or Bus 2.
• E8 enclosure (36H×30W×6.5D in) supports B100 battery backup and NLC supervision.

Lifesafety Power · FPO250/250-B1002C82D8E6M1

Lifesafety Power FPO250/250-B1002C82D8E6M1 250W power supply 20A

250W power supply built for access control and life-safety systems that require fused, supervised outputs for electric locks and auxiliary devices

• Delivers 20A@12VDC or 10A@24VDC to support mid-scale multi-door lock deployments.
• Eight relay outputs are individually fused at 3A with per-output FAI, failsafe, or failsecure mode.
• Eight auxiliary DC outputs are Bus1/Bus2 assignable, supporting multi-bus campus architectures.

Lifesafety Power · FPO250/250-B1002D8E4M1

Lifesafety Power FPO250/250-B1002D8E4M1 250W power supply 20A/12

250W regulated power supply designed for multi-camera and access-control deployments requiring dual-voltage flexibility

• Delivers 20A at 12VDC or 10A at 24VDC via jumper selection for mixed-voltage sites.
• Eight independently fused 3A outputs with Bus1/Bus2 switching isolate load faults per branch.
• Fixed 250W output suits stable-grid installs where UPS protection is managed separately.

Lifesafety Power · FPO250/250/250-3C83D8PE12M

Lifesafety Power FPO250/250/250-3C83D8PE12M 250W power supply

250W dual-voltage power supply designed to centralize power distribution and relay control for door locks, strike plates, and auxiliary load

• 8 independently fused 3A relay outputs support FAI, failsafe, or failsecure per door.
• Selectable 12VDC/24VDC output eliminates separate supplies on mixed-voltage deployments.
• 8 Class 2 auxiliary outputs at 2.5A each power REX buttons, sensors, and indicators.

Lifesafety Power · FPO250/250/250-3C85D8PE12M/P24-A

Lifesafety Power FPO250/250/250-3C85D8PE12M/P24-A 3 x 250W power

Modular, high-capacity power supply designed for mid-to-large access control installations requiring distributed lock control and auxiliary circuit

• Three 250W modules deliver 750W aggregate capacity for 20+ door deployments.
• 24 relay outputs support magnetic locks, strikes, and motor deadbolts at 12 or 24VDC.
• 40 Class 2 auxiliary outputs power readers, sensors, and intercoms on isolated buses.

Lifesafety Power · FPO250/250/250-3D8P5M8PNLCE12M/P24-B

Lifesafety Power FPO250/250/250-3D8P5M8PNLCE12M/P24-B Mercury Pro

750W dual voltage access control power supply designed to support mid-to-large security installations requiring distributed power to door locks

• 750W total output powers 40 managed lock outputs and 24 auxiliary channels from one shelf.
• Centralized distribution eliminates separate power runs per zone, reducing installation labor.
• 120 VAC single-phase input integrates into standard mains without special service requirements.

Lifesafety Power · FPO250/250/250-4C84D8E12S

Lifesafety Power FPO250/250/250-4C84D8E12S 250W power supply 20A

250W power supply designed to distribute power and relay control across networked access control and security systems

• Delivers 20A at 12VDC or 10A at 24VDC from a single 250W supply.
• 32 relay lock outputs, each 3A fused with per-output FAI/failsafe/failsecure selection.
• 32 isolated DC auxiliary outputs eliminate external relay banks in cabinet installs.

Lifesafety Power · FPO250/250/250-8M8PNLCE12M/P24-A

Lifesafety Power FPO250/250/250-8M8PNLCE12M/P24-A 250W power supp

250W managed power distribution unit engineered for mid-scale security deployments where independent circuit isolation and per-channel protection are

• Eight isolated Class 2 outputs at 2.5A each prevent single-fault cascade failures.
• Selectable 12V/20A or 24V/10A operation supports legacy and modern access control hardware.
• 250W total capacity covers mid-scale deployments of 8–12 IP cameras or 4–6 access panels.

Lifesafety Power · FPO250/E-BOXED

Lifesafety Power FPO250/E-BOXED Smart DC Power Supply/Charger 208

• Accepts 208–230VAC mains input, compatible with standard commercial electrical infrastructure.
• Fully enclosed BOXED form factor mounts to DIN rail, wall bracket, or cabinet surface.
• Integrated charging circuit supports battery backup systems alongside regulated DC output.

Lifesafety Power · FPO75-2D8E1

Lifesafety Power FPO75-2D8E1 75W power supply 6A/12V or 3A/24V 1

75W auxiliary power supply designed to distribute regulated DC power across multiple power supply branches in networked security installations

• 16 independently fused 3A outputs eliminate single failure points across distributed loads.
• Per-output Bus1/Bus2 selection isolates zones or backup domains during commissioning.
• Compact 14H×12W×4.5D-inch enclosure fits standard DIN rail or wall-mount security cabinets.

Lifesafety Power · FPO75-2D8E4M

Lifesafety Power FPO75-2D8E4M 250W PS 20A/12V or 10A/24V 24 DC au

250W auxiliary power supply designed for distributed access control and electromagnetic lock circuits in commercial security deployments

• Selectable 20A/12V or 10A/24V output eliminates buck/boost conversion on mixed-voltage sites.
• Four independent 2.5A Class 2 channels isolate lock, reader, and RTE circuits without daisy-chaining.
• Dual-bus per-output assignment prevents single-fault cascade across up to 24-door deployments.

Lifesafety Power · FPO75-2D8E4M1

Lifesafety Power FPO75-2D8E4M1 75W power supply 6A/12V or 3A/24V

Compact 75W power supply designed for distributed access control, alarm, and IP device deployments where multiple 12VDC or 24VDC circuits require

• Eight individually fused 3A outputs prevent cascade failures across locks and readers.
• Selectable 12V/24V per output supports mixed device loads from a single 75W supply.
• Dual-bus architecture enables fault isolation in supervised access control deployments.

Lifesafety Power · FPO75-2D8PE1

Lifesafety Power FPO75-2D8PE1 75W power supply 6A/12V or 3A/24V

75W power supply purpose-built for small-to-medium distributed surveillance and access control deployments

• 16 supervised Class 2 outputs (2.5A each) isolate faults without cascading failures.
• Dual-bus architecture segments 12V and 24V loads in one panel, reducing wiring complexity.
• E1 enclosure (14H×12W×4.5D in.) mounts on 19-inch rack rails or wall on 4-inch centers.

Lifesafety Power · FPO75-2D8PE2M

Lifesafety Power FPO75-2D8PE2M 75W power supply 6A/12V or 3A/24V

75W regulated power supply designed to distribute power across distributed security and access-control installations

• Delivers 6A@12VDC or 3A@24VDC from one AC input to fit mixed-voltage site designs.
• Eight independently current-limited 2.5A outputs reduce homerun wiring across access zones.
• Per-output Bus1/Bus2 assignment enables zone isolation without additional distribution hardware.

Lifesafety Power · FPO75-B1002D8E1

Lifesafety Power FPO75-B1002D8E1 Std Pow Sys 75W Dual Voltage

UL-listed power distribution system designed for access control, life safety, and emergency egress applications

• Dual 12V/24V zone-selectable outputs eliminate separate supplies in mixed-voltage installs.
• Integrated fire alarm disconnect relay automatically unlocks doors on alarm—no aux wiring needed.
• Low-battery cutoff and dedicated fast charger extend SLA/lithium backup battery service life.

Lifesafety Power · FPO75-B100C4D8E1

Lifesafety Power FPO75-B100C4D8E1 75W Dvps 4 Lock Control Out

75W distributed power supply (DVPS) designed to power access control systems, electronic locks, and auxiliary devices in security installations

• 75W DVPS powers four 3A-fused lock control outputs at 12V or 24V.
• Eight additional fused auxiliary outputs support sensors, REX, and door position switches.
• 120 VAC input fits standard dedicated circuits; E1 enclosure mounts near the access panel.

Lifesafety Power · FPO75-B100C4D8E1M

Lifesafety Power FPO75-B100C4D8E1M 75W power supply 6A/12V 12V 2

75W power distribution module designed for access control, door lock, and auxiliary device management in security installations

• 12 fused outputs (4 relay lock + 8 auxiliary DC) consolidate door and device power.
• Per-output failsafe/failsecure/FAI selection meets life-safety door locking requirements.
• Adjustable 5–18V @ 4A output supports legacy non-standard-voltage devices without regulators.

Lifesafety Power · FPO75-B100C4D8E2

Lifesafety Power FPO75-B100C4D8E2 Power supply board 75W 6A/12V

Compact 75W power supply board designed to distribute regulated DC power across multiple IP cameras and networked security endpoints in integrated

• Delivers 6A at 12VDC or 3A at 24VDC, eliminating separate supplies in mixed-voltage installations.
• 75W capacity supports 6–12 megapixel cameras or mixed PoE and non-PoE endpoints from one board.
• Board-level form factor integrates into cabinet or DIN-rail assemblies for centralized power distribution.

Lifesafety Power · FPO75-B100C4D8E2S

Lifesafety Power FPO75-B100C4D8E2S 75W PS 6A/12V or 3A/24V 12V 2

Dedicated access control power supply engineered for mid-scale door control installations, supporting multiple electric lock, strike, and auxiliary

• Dual primary output (6A/12V or 3A/24V) supports mixed lock ecosystems from one 75W unit.
• Four 3A relay outputs with per-relay FAI/failsafe/failsecure selection cut multi-door wiring time.
• Eight 3A auxiliary outputs with Bus1/Bus2 assignment eliminate external multiplexing hardware.

Lifesafety Power · FPO75-B100C4D8E2X

Lifesafety Power FPO75-B100C4D8E2X 75W power supply 6A/12V or 3A

75W power supply designed to deliver both primary load power and integrated relay logic control for distributed access control and security device

• Delivers 6A/12V or 3A/24V primary output plus adjustable 5–18VDC at 4A for legacy devices.
• Four relay outputs support failsafe, failsecure, or FAI logic—each fused at 3A for circuit protection.
• Eight auxiliary DC outputs assignable to Bus1 or Bus2 prevent cross-loading across independent control circuits.

Lifesafety Power · FPO75-B100C4D8E4M

Lifesafety Power FPO75-B100C4D8E4M Power supply board 75W 6A/12V

75W power supply board designed for access control and fire-safety system installations

• 75W board delivers 6A/12V and 3A/24V outputs for multi-door access control runs.
• Four 3A relay lock outputs plus eight 3A auxiliary DC outputs support large deployments.
• Ships with Mercury/Lenel backplate for drop-in integration into standard enclosures.

Lifesafety Power · FPO75-B100C4D8PE2

Lifesafety Power FPO75-B100C4D8PE2 PSB 75W 6A/12V or 3A/24V Seco

Class 2 power supply board designed for mid-scale access control, intercom, and security system installations

• Selectable 6A/12V or 3A/24V output covers most door locks and reader loads.
• 4 independently fused 3A relay outputs isolate faults without taking down adjacent circuits.
• Class 2 topology meets NEC/CEC low-voltage rules, eliminating conduit separation requirements.

Lifesafety Power · FPO75-B100C4D8PE2M/P4-A

Lifesafety Power FPO75-B100C4D8PE2M/P4-A 75W PS 6A/12V or 3A/24V

75W distributed power supply designed for access control, door locks, and life safety integration in commercial and institutional facilities

• Selectable 6A/12V or 3A/24V output powers lock actuators without extra supplies.
• Four independently fused relay outputs support failsafe or failsecure mode per door.
• Eight Class 2 auxiliary outputs distribute sensor and indicator loads across two buses.

Lifesafety Power · FPO75-B100C4D8PE2M/P4-C

Lifesafety Power FPO75-B100C4D8PE2M/P4-C 75W PS 6A/12V or 3A/24V

75W power supply module designed for distributed access control and security system deployments requiring multiple lock and auxiliary outputs

• Selectable 12V/6A or 24V/3A output supports mag-lock and solenoid strike installs from one unit.
• 4 relay lock outputs (3A each) with per-output FAI, failsafe, or failsecure logic eliminate external relay racks.
• 8 auxiliary Class 2 outputs at 2.5A each cover sensors, LEDs, and signaling across 4–8 door zones.

Lifesafety Power · FPO75-B100C4D8PE2M/T4-C

Lifesafety Power FPO75-B100C4D8PE2M/T4-C FPO75-B100C4D8PE2M/T4-C

75W industrial-grade power supply built for Lifesafety Power's Mercury access control platform

• Delivers 2A at 12V and 2A at 24V simultaneously from a single 75W unit.
• Prewired E2M configuration with tie-wrap assembly cuts on-site labor and wiring errors.
• Supports 4 door outputs and 8 auxiliary outputs for Mercury platform deployments.

Lifesafety Power · FPO75-B100C4D8PE4M1

Lifesafety Power FPO75-B100C4D8PE4M1 75W power supply 6A/12V

75W power module engineered for distributed power supply deployments in access control, door management, and security system installations

• Dual-voltage output (12VDC/6A or 24VDC/3A) supports mixed legacy and modern device ecosystems.
• Four independently fused relay outputs with FAI logic enable coordinated emergency lockdown control.
• Eight bus-selectable 2.5A auxiliary outputs simplify multi-zone wiring and fault isolation.

Lifesafety Power · FPO75-B100C4D8PNLCE2M/T4-A

Lifesafety Power FPO75-B100C4D8PNLCE2M/T4-A 75W power supply 6A

75W regulated power supply purpose-built for distributed access control installations

• Dual-voltage output (12VDC/6A or 24VDC/3A) supports mixed-voltage lock deployments.
• Four individually fused relay outputs with per-door failsafe/failsecure logic selection.
• Eight Class 2 auxiliary outputs expand signaling capacity without additional relay modules.

Lifesafety Power · FPO75-B100C4E1M

Lifesafety Power FPO75-B100C4E1M Power supply board 75W 6A/12V

75W redundant power supply with dual independent outputs—2A @ 12VDC and 2A @ 24VDC—designed to power access control systems, door locks, and

• Dual independent outputs (12VDC @ 2A and 24VDC @ 2A) support mixed-voltage installations.
• Four individually fused lock outputs isolate circuit faults without tripping the entire supply.
• E1M enclosure (14H×12W×4.5D in.) fits standard wall-mount or rack-install security closets.

Lifesafety Power · FPO75-B100C4E2M

Lifesafety Power FPO75-B100C4E2M Power supply board 75W 6A/12V

Dual-output power supply board engineered for access control and integrated security systems

• Dual-output design powers 12V/24V primary and adjustable 5–18V secondary from one 75W board.
• Four isolated 3A relay outputs switch locks independently, protecting video and data circuits.
• Size 18 enclosure with Mercury/Lenel backplate fits existing cabinet stacks without rewiring.

Lifesafety Power · FPO75-B100C4E2V

Lifesafety Power FPO75-B100C4E2V Power supply board 75W 6A/12V

75W power supply engineered for Vertx 4DR networked lock systems and associated access-control hardware

• 75W dual-output power supply for Vertx 4DR networked locks
• Simultaneous 12VDC and 24VDC output at 2A each
• 8 fused lock/auxiliary outputs in stainless E2V enclosure