Mounting Brackets & Kits for IP Cameras

Plan Your Deployment

Wall, ceiling, pole, or corner mounting requirements
Indoor vs outdoor environmental exposure
Device model compatibility and load capacity
Vandal resistance and tamper considerations
Future service access and cable routing planning

Sub categories

Showing Results for Mounting Brackets & Kits

Compare

Add to Cart The item has been added
Hanwha

SKU: SBO-140BW

Hanwha SBO-140BW Backbox for Bullet Camera

Aluminum weatherproof backbox for Hanwha bullet cameras, IP66/IK10
- IP66 rating blocks rain jets and dust; IK10 resists 20-joule impacts
- Aluminum construction weighs 980g for one-person installation
- Compact ø147.5 × 73.3mm form factor hides cable runs at camera head
In stock · Usually Ships Same Business Day

$49.00 $36.99 Save $12.01

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Hanwha

SKU: SBO-140WW

Hanwha SBO-140WW Aluminum Back Box Camera Enclosure

IP66 aluminum back box for Hanwha outdoor camera mounting
- IP66-rated enclosure shields against dust and high-pressure water jets
- Lightweight aluminum (870g) reduces wall and pole installation load
- TR20 mount compatibility across 8 Hanwha camera models
In stock · Usually Ships Same Business Day

$76.00 $56.99 Save $19.01

Add to Cart
The item has been added
Compare

Out of stock
Hanwha

SKU: SBP-004PBW

Hanwha SBP-004PBW Mounting Converter 4 to 4.75 Inch

4" to 4.75" PCD mounting converter for wall and ceiling install
Special Order · Usually Ships in 2-3 Weeks

$170.00 $129.99 Save $40.01

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Hanwha

SKU: SBP-004WMW

Hanwha SBP-004WMW Wall Mount for Rugged PTZ Cameras

Wall mount for rugged PTZ cameras, 15 kg load capacity, reversible angles
In stock · Usually Ships Same Business Day

$420.00 $310.99 Save $109.01

Add to Cart
The item has been added
Compare

Out of stock
Hanwha

SKU: SBP-050NBW

Hanwha SBP-050NBW Installation Cabinet

IP66/IK10 compact cabinet for outdoor Hanwha camera installations
Special Order · Usually Ships in 2-3 Weeks

$330.00 $244.99 Save $85.01

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Hanwha

SKU: SBP-050PMW

Hanwha SBP-050PMW Pole Mount Bracket

Aluminum pole and wall bracket for mid-range cameras up to 15 kg
In stock · Usually Ships Same Business Day

$75.00 $57.99 Save $17.01

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Hanwha

SKU: SBP-060S

Hanwha SBP-060S Stainless Steel Mount Strap

Marine-grade stainless steel pole mount for coastal & corrosive environments
- SUS316L stainless steel resists salt spray and humidity without rusting
- Fits poles 80–160mm diameter; 600mm strap length secures dual cameras
- Two straps per package for redundant fastening or multi-camera setup
In stock · Usually Ships Same Business Day

$30.00 $22.99 Save $7.01

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Hanwha

SKU: SBP-099TMW

Hanwha SBP-099TMW Tilted Wall Mount White

20° tilted wall mount for Hanwha fisheye cameras, white polycarbonate
- 20-degree fixed tilt redirects fisheye coverage downward without gimbal adjustment
- Compact Ø99mm footprint in UV-resistant white polycarbonate for indoor/covered outdoor
- Direct fit for QNF-8010 and QNF-9010 fisheye cameras, 100g lightweight design
In stock · Usually Ships Same Business Day

$49.00 $37.99 Save $11.01

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Hanwha

SKU: SBP-115PA

Hanwha SBP-115PA Wall and Pole Mount Adapter Pack of 3

Shaft adapters (pack of 3) for Hanwha PTZ wall and pole mounts
In stock · Usually Ships Same Business Day

$150.00 $114.99 Save $35.01

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Hanwha

SKU: SBP-115PFA

Hanwha SBP-115PFA Wall and Pole Mount Adaptor Pack of 3

1.5" PF adaptor pack of 3 for wall and pole mounting Hanwha cameras
In stock · Usually Ships Same Business Day

$150.00 $114.99 Save $35.01

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Hanwha

SKU: SBP-120WM

Hanwha SBP-120WM Indoor Wall Mount Bracket

Wall mount bracket for Hanwha QND, XND, SND-L, and SCD cameras
- Lightweight 360g design minimizes load on drywall anchors and mounts
- Works across 20+ Hanwha camera models, reducing bracket inventory needs
- Includes mounting template, fasteners, and hardware for complete installation
In stock · Usually Ships Same Business Day

$25.00 $19.99 Save $5.01

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Hanwha

SKU: SBP-122HMW

Hanwha SBP-122HMW Aluminum Hanging Mount

Lightweight aluminum ceiling mount for Hanwha dome cameras, -50–60°C
- 159g aluminum construction minimizes installation load on ceiling hardware
- Operates across full humidity range 0–100% without corrosion or degradation
- 1½" NPT male thread fits 8 Hanwha QND and QNV camera models directly
In stock · Usually Ships Same Business Day

$34.00 $25.99 Save $8.01

Add to Cart
The item has been added
Compare

Out of stock
Hanwha

SKU: SBP-125HMW

Hanwha SBP-125HMW White Mounting Cap

White aluminum mounting cap for Hanwha Wisenet cameras, PF 1 1/2" thread
- Aluminum construction with white finish resists corrosion on interior/exterior mounts
- PF 1 1/2" thread size matches Hanwha Wisenet cameras including QNE-8011R
- Compact 5.39" diameter × 1.85" height minimizes protrusion from ceiling/wall surfaces
Special Order · Usually Ships in 2-3 Weeks

$34.00 $25.99 Save $8.01

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Hanwha

SKU: SBP-125WMW1

Hanwha SBP-125WMW1 Wall/Pole Mount for Dome Cameras

Wall or pole mount for Hanwha dome cameras, aluminum body
- Dual mounting capability—single bracket works on walls or poles
- Aluminum body with polycarbonate cover resists corrosion outdoors
- Lightweight at 505g with adjustable positioning to aim camera
In stock · Usually Ships Same Business Day

$65.00 $49.99 Save $15.01

Add to Cart
The item has been added
Compare

Out of stock
Hanwha

SKU: SBP-137WM1

Hanwha SBP-137WM1 Dome Hanging Wall Mount

Dome hanging wall mount for flexible Hanwha camera placement
- Works with Hanwha dome cameras; includes bracket and hardware
- Durable construction designed for retail, lobbies, and warehouses
- Hanging design optimizes ceiling or wall positioning for coverage
Special Order · Usually Ships in 2-3 Weeks

$65.00 $49.99 Save $15.01

Add to Cart
The item has been added
Compare

Out of stock
Hanwha

SKU: SBP-140C

Hanwha SBP-140C Mounting Hole Cover Plate

White polycarbonate cover plate for Hanwha dome camera mounts
Special Order · Usually Ships in 2-3 Weeks

$30.00 $22.99 Save $7.01

Add to Cart
The item has been added

What to Look For When Buying

The decisions that matter most before you spec.

Load Rating & Vibration Damping

Mounting brackets must support camera weight (typically 0.5–15 lbs for IP cameras) plus wind load in outdoor deployments. Improperly secured cameras cause system failure during critical incidents; select brackets rated for your camera model and environmental stress factors. Gyro mounts and rubber isolators reduce vibration in high-wind or traffic-adjacent zones.

Cable Routing & PoE Management

Mounting kits with integrated cable glands and strain relief prevent cable pinch points and maintain PoE power delivery stability. Conduit clips and backing plates organize cables at the source, reducing troubleshooting time and protecting against accidental disconnection during maintenance.

Material & Corrosion Resistance

Outdoor and coastal installations require stainless steel or powder-coated aluminum brackets to prevent rust and material degradation. Salt spray, humidity, and UV exposure degrade standard steel within 6–12 months; specify 300/316 stainless for marine environments and 6063 aluminum for standard outdoor use.

Installation Standard & Brand Compatibility

Major brands like Axis, Hanwha, and Vivotek design proprietary mounting interfaces alongside VESA and ISO standard mounts. Verify bracket compatibility with your camera model before procurement; cross-brand mounts may misalign optical paths or create cable stress points.

Height, Angle & Optical Alignment

Camera mounting height and tilt affect pixel density and DORI (Detection, Observation, Recognition, Identification) distances. Adjustable brackets allow field-level fine-tuning; fixed mounts require accurate site survey and pre-deployment calculations to avoid costly repositioning after installation.

Conduit Seal & Weatherproofing

Water ingress at cable entry points causes short circuits and sensor corrosion in wet environments. Select kits with silicone gaskets, stainless steel cable glands, and IP67-rated enclosures; test seals during initial deployment to prevent mid-season failures.

Technology Stack

The specs and acronyms that actually affect mounting brackets & kits performance.

VESA Mount Standards (75/100/200 mm)

Standardized hole patterns used by consumer electronics and some IP camera models. Allows universal bracket compatibility across manufacturers, but always verify camera's screw pitch and load rating before mixing brands.

Wind Load Rating (lbs @ mph)

Manufacturers specify maximum wind speed brackets withstand without camera slip or structural flex. Outdoor installations require ratings matching local weather extremes; most outdoor brackets support 60–120 mph sustained winds, but rooftop or exposed mounting may demand 150+ mph ratings.

Stainless Steel Grades (304/316)

Grade 304 resists general corrosion in most climates; Grade 316 adds molybdenum for superior salt-spray tolerance in coastal zones. Galvanized steel (zinc coating) offers cost savings but degrades 3–5 years faster than stainless in humid/marine environments.

Cable Gland Certifications (IP67/IP68)

IP rating indicates water and dust ingress protection at cable entry. IP67 withstands temporary immersion; IP68 is rated for continuous submersion. Select IP67 minimum for outdoor camera mounts, IP68 for wet-room intercoms and dock-area access readers.

Gyro Mounts & Vibration Damping

Rubber or elastomer isolators reduce micro-vibrations transmitted from poles or wind, stabilizing video in high-motion environments. Critical for PTZ cameras on rooftop poles or traffic-adjacent installations; adds 0.5–2 lbs to mounting weight.

Conduit Diameter & Strain Relief

Brackets specify maximum conduit size (typically 0.5–1.5 inches) and cable bend radius. Exceeding bend-radius limits degrades PoE conductor insulation; use clips and backing plates to maintain manufacturer-specified minimum bend radius (usually 4–6 inches for Ethernet).

Typical Deployment Scenarios

Multi-Story Office Lobby (15 cameras, mixed mount types)

Combine ceiling-mount brackets for overview domes at entry points, corner brackets for stairwell coverage, and recessed in-wall mounts for elevator vestibules. Use Hanwha or Axis unified bracket kits to simplify procurement; junction-box assemblies pre-mount cable glands and backing plates, reducing on-site assembly by 40%.

Outdoor Parking Lot Perimeter (24 cameras, 30-ft poles)

Specify heavy-duty pole mounts rated for 80+ mph wind load, stainless steel hardware, and gyro isolation for vibration damping. Include pendant conduit kits with silicone gaskets and IP67 glands; plan cable routing inside pole conduit to protect PoE runs from weather and UV degradation.

Hospital Intercom & Card-Reader Network (40 stations, recessed mount)

Use recessed trim-ring kits designed for flush in-wall mounting at staff stations, nurse calls, and secure doors. Select 316 stainless trim rings; pair with concealed junction boxes to route cables through wall cavities, maintaining clean aesthetics while protecting core network connections from physical damage.

Warehouse Dock & Data-Capture Zone (8 cameras, industrial-grade PTZ)

Heavy-duty PTZ mounts on gantry beams require gyro dampers and reinforced backing plates rated for 20+ lbs static load. Route PoE and pan-tilt control cables through conduit; ensure sufficient power budget per PoE planning guidance for simultaneous motor operation across all units.

Frequently Asked Questions

What's the difference between VESA and proprietary camera mounts?

VESA (75/100/200 mm) are universal screw-hole patterns used by monitors and some IP cameras, allowing mixed-brand bracket compatibility. Proprietary mounts are manufacturer-specific and often integrate cable routing and power connectors for a given camera family. Always verify your camera's mounting interface before ordering; mixing standards can misalign the lens or create cable stress.

How do I choose between wall, pole, and ceiling mounting?

Wall mounts suit indoor hallways and perimeter coverage; ceiling mounts provide overhead overview angles; pole mounts enable tall outdoor installations for parking lots and large perimeters. Consider viewing angle (DORI distance), cable routing (PoE run length), and environmental exposure (rain, wind, UV). Outdoor deployments typically require pole or soffit brackets with stainless hardware and weatherproof conduit seals.

What wind-load rating do I need for rooftop or pole-mounted cameras?

Most outdoor brackets are rated 60–80 mph; rooftop and tall-pole installations in high-wind zones (hurricane, mountain, or exposed coastal areas) require 100–150+ mph ratings. Consult local building codes and weather records for your site. Undersized brackets allow camera drift, misaligning views and degrading identification accuracy over distance.

Why should I use stainless steel brackets in coastal or humid climates?

Standard steel and galvanized coatings corrode within 2–5 years in salt-spray or high-humidity zones, causing bracket failure and camera drop hazards. Stainless 304 resists general corrosion; 316-grade adds molybdenum for superior marine tolerance. The upfront cost (typically 20–40% more) prevents emergency replacement and liability exposure.

What's an IP67 cable gland, and why does it matter for outdoor mounts?

IP67 means the gland prevents dust and temporary water submersion at cable entry points. Water ingress corrodes connectors and shorts PoE circuits, causing mid-deployment failures. Pair IP67 glands with silicone gaskets and stainless fasteners; test seals before final installation to confirm weatherproofing.

Can I use the same mounting bracket for different camera brands?

Only if both cameras share VESA or ISO mounting standards. Proprietary mounts (common in Axis, Vivotek, and Hanwha models) are not interchangeable. Mixing brands often requires adapter plates, which add bulk, cost, and potential optical misalignment. Standardize on one or two manufacturer families per project to simplify spare-parts inventory and on-site troubleshooting.

Mounting Brackets & Kits

Plan Your Deployment

Sub categories

Showing Results for Mounting Brackets & Kits

Hanwha SBO-140BW Backbox for Bullet Camera

Hanwha SBO-140WW Aluminum Back Box Camera Enclosure

Hanwha SBP-004PBW Mounting Converter 4 to 4.75 Inch

Hanwha SBP-004WMW Wall Mount for Rugged PTZ Cameras

Hanwha SBP-050NBW Installation Cabinet

Hanwha SBP-050PMW Pole Mount Bracket

Hanwha SBP-060S Stainless Steel Mount Strap

Hanwha SBP-099TMW Tilted Wall Mount White

Hanwha SBP-115PA Wall and Pole Mount Adapter Pack of 3

Hanwha SBP-115PFA Wall and Pole Mount Adaptor Pack of 3

Hanwha SBP-120WM Indoor Wall Mount Bracket

Hanwha SBP-122HMW Aluminum Hanging Mount

Hanwha SBP-125HMW White Mounting Cap

Hanwha SBP-125WMW1 Wall/Pole Mount for Dome Cameras

Hanwha SBP-137WM1 Dome Hanging Wall Mount

Hanwha SBP-140C Mounting Hole Cover Plate

Browse by Product Family

What to Look For When Buying

Technology Stack

Typical Deployment Scenarios

Top Brands for Mounting Brackets & Kits

Frequently Asked Questions

Related Categories

Engineering Reading