PoE Injectors & Midspans

Selecting a sort option will reload the product list.

Showing Results for PoE Injectors & Midspans

PoE Injectors & Midspans

PoE injectors and midspans provide Power over Ethernet to devices such as IP cameras, intercoms, and access control hardware. These solutions are ideal when adding PoE to non-PoE switches or expanding power capacity in existing network deployments.

Plan Your Deployment

  • Power requirements (PoE, PoE+, PoE++, total wattage)
  • Number of devices and port capacity planning
  • Distance limitations and cable quality considerations
  • Integration with existing switches and infrastructure
  • Redundancy and long-term scalability needs
PoE Planning Guide Get Recommendations

PoE Injectors & Midspans — Engineering-Grade PoE Power Delivery for Commercial Deployments

This category covers 294 working models of poe injectors & midspans sourced manufacturer-direct or through channel-direct US distribution. Build the rest of your system around the architectural choices below — compatibility, environmental rating, and lifecycle decisions made here propagate through every downstream component you specify.

What to Look For

Match the PoE class to the device load. 802.3af delivers up to 15.4W at the source (12.95W at the device) and powers most fixed-lens cameras and access readers. 802.3at (PoE+) reaches 30W and supports motorized cameras, illuminators, and heated outdoor housings. 802.3bt (PoE++/4PPoE) goes to 60-90W for large PTZs, multi-imagers, and devices with integrated heaters and wipers.

Single-port injectors vs. midspan multiport units depends on the scale. A handful of cameras at fixed locations are economical with single-port injectors near the device. Sites with 16+ PoE devices benefit from a midspan (Microsemi PowerDsine, Phihong, Lantronix) that consolidates power management. PoE switches absorb the role for larger sites where unmanaged power is acceptable.

Cable length and conductor gauge affect deliverable power. 100 m of Cat5e at full 802.3bt load drops voltage enough that some devices report under-volt errors. For runs near the 100m limit, use Cat6 with all 4 pairs and confirm the injector's voltage-at-source spec. For longer-than-spec runs, PoE extenders (Veracity, Phybridge, ComNet) regenerate the signal mid-run.

Surge protection, grounding, and outdoor-rated housings matter for exterior PoE injectors. Lightning-induced surges destroy PoE-powered devices through the network cable as quickly as direct strikes. Inline ethernet surge protectors (Ditek, Transtector) at both ends of the run protect both the injector and the camera. Use Cat6A shielded for runs exiting the building, with proper grounding at the equipment rack.

Key Specs in This Category

SpecAvailable Options
ResolutionThermal, 6MP, 20MP+
IP RatingIP68, IP66
ConnectivityWired, Single-Mode Fiber, Multi-Mode Fiber, Wi-Fi, Ethernet over Coax, WiFi + Wired
PowerPoE+, PoE, PoE++, AC/DC, 24VAC, 12VDC
Channels8
TypePower Supply, Switch, PoE Adapter, PoE Injector, PoE Switch, Network Hub, PoE Device, Media Converter

Related Categories

Or browse all Power & UPS.

Top Brands in This Category

Frequently Asked Questions

What's the difference between 802.3af, 802.3at, and 802.3bt?

802.3af (PoE) provides up to 15.4W at the source — standard for fixed cameras and access readers. 802.3at (PoE+) reaches 30W — for motorized cameras, illuminators, and small PTZs. 802.3bt (PoE++/4PPoE) reaches 60-90W (Type 3 and Type 4) — for multi-imager cameras, large outdoor PTZs, and devices with integrated heaters. Match the injector class to the device's PoE rating; over-spec'd injectors don't harm devices but cost more.

Can I run PoE on Cat5e or do I need Cat6?

Cat5e supports 802.3af and 802.3at to the full 100 m run length without issue. For 802.3bt at 60W+ over long runs, Cat6 with shielded conductors is more reliable — Cat5e can deliver but voltage drop approaches the limits of the spec. For new installs, Cat6 is the safe baseline; for retrofits over existing Cat5e, validate end-to-end voltage at the device after installation.

How far can PoE run?

The IEEE standard caps PoE at 100 m on copper. PoE extenders (Veracity Outreach, Phybridge UniPoE, ComNet PoE extenders) regenerate the signal at intermediate points and stretch the effective run to 300-1000 m depending on the product. For runs beyond 100 m on a single segment, fiber-to-the-camera with media converters is often cheaper than chained extenders.

Do I need a PoE injector if I already have a PoE switch?

If your PoE switch has sufficient per-port budget and total PoE budget for all connected devices, no — the switch handles power delivery. Injectors are needed when (a) the existing switch is non-PoE and replacing it isn't viable, (b) a single device needs higher PoE class than the switch supports, or (c) the device is placed far from the switch and a local injector with shorter run is preferable.

Will a PoE+ device work on a PoE switch port?

Only if the switch port delivers 802.3at (PoE+) or higher. A pure 802.3af port (15.4W max) cannot reliably power an 802.3at device that needs up to 30W — the device will fail to negotiate or will reset under load. Confirm the switch's per-port PoE class capability in its datasheet, not just the aggregate PoE budget. Many older switches are af-only despite total-budget numbers that suggest otherwise.

Need help choosing? Talk to a Senior Specialist — direct line 877-277-7147 or request a quote.

!