Which credential technology and Wiegand output protocol does each reader support?

The 40TKS-00-000000 SIGNO 40 outputs Wiegand 32-bit MSB and is designed for EM 4100/4102-compatible proximity cards (32-bit EM card format). This is a less common Wiegand variant; panels must explicitly support 32-bit MSB framing, and existing badge stock must be EM-format for a direct migration.

The 5365EGP00 MiniProx outputs SIA 26-bit Wiegand, the de facto industry standard protocol. It reads 125 kHz HID proximity cards and fobs. The 26-bit format is natively supported by virtually every legacy and current access control panel on the market, making it the lower-integration-risk choice. The specs also list RS-232 and MIFARE credential references, though these appear inconsistent with the primary proximity-only positioning; buyers should verify against the datasheet before relying on MIFARE or RS-232 capability.

For installations already running HID 125 kHz prox cards on a 26-bit panel infrastructure, the MiniProx is a drop-in credential match. For sites running EM card stock and a panel that accepts 32-bit MSB, the SIGNO 40 allows badge reuse without re-issue.

How do the physical dimensions and mounting options differ between the two readers?

The 5365EGP00 MiniProx measures 6.0" × 1.7" × 1.0" and is specifically designed for mullion mounting—the narrow vertical strip between door glass panels—as well as direct mounting on metal surfaces without custom brackets. Its slim profile is suited to retrofits where wall space is constrained or aesthetics matter at a narrow door frame.

The 40TKS-00-000000 SIGNO 40 is listed with dimensions of 80" × 121.5" × 19.5". These figures are almost certainly a data-entry error and should not be used for rough-in planning; the datasheet at /content/product-datasheets/40TKS-00-000000.pdf must be consulted before ordering. It is described as a standard-profile surface-mount reader with terminal block and pigtail wiring options, suited for wall mounting in both indoor and outdoor environments.

Until the SIGNO 40 dimension error is resolved, installers cannot reliably compare cutout or backbox requirements. The MiniProx dimensions are clean and confirmed, making pre-installation planning straightforward for that model.

What are the power requirements, environmental ratings, and panel integration considerations for each reader?

The 40TKS-00-000000 SIGNO 40 is specified at 12VDC (standard) and is rated for both indoor and outdoor use. It provides visual and audible feedback via a red LED, green flash indicator, and integrated buzzer. Wiring is via terminal block or pigtail. No IP or IK rating is stated in the provided specs.

The 5365EGP00 MiniProx is specified at 5VDC, a lower voltage that may require attention at the panel's reader power supply if the panel typically outputs 12VDC. It includes a built-in tamper switch that signals tampering events directly to the panel without additional sensor wiring—a meaningful installation and compliance advantage. Environmental ratings and LED feedback behavior are not specified in the provided data.

The 12VDC versus 5VDC difference is a practical wiring concern: installers must verify the panel's reader port output voltage or supply a 5VDC source for the MiniProx. Both readers use wired Wiegand connections to the panel; neither introduces network infrastructure requirements. No software management platform is listed for either reader.

Which should you choose: the 40TKS-00-000000 or the 5365EGP00?

Our take: The 5365EGP00 MiniProx is the stronger choice when the installation uses HID 125 kHz proximity cards on a standard 26-bit Wiegand panel infrastructure and requires a physically slim form factor for mullion or narrow-frame mounting. Three concrete spec deltas support this: the MiniProx outputs SIA 26-bit Wiegand versus the SIGNO 40's less common 32-bit MSB, meaning broader panel compatibility out of the box; the MiniProx's confirmed 6.0" × 1.7" × 1.0" profile is purpose-built for mullions while the SIGNO 40's published dimensions contain an apparent data error that prevents reliable rough-in planning; and the MiniProx includes a built-in tamper switch—not listed for the SIGNO 40—adding panel notification without extra wiring. Conversely, the SIGNO 40 is preferable where the existing badge stock is EM 4100/4102-format and the panel accepts 32-bit MSB, or where 12VDC reader power and outdoor-rated surface-mount form factor are the primary constraints.

Side-by-Side Comparison

Spec-for-spec, from manufacturer data.

Frequently Asked Questions

Related Resources

• HID 40TKS-00-000000 product page — full specs and to add to a quote
• HID 5365EGP00 product page — full specs and to add to a quote