IP Camera Accessories | Mounts, Enclosures, Lenses, IR & Power

Deployment Considerations

Environmental protection and weather resistance
Mounting stability and load support
Power and voltage compatibility
Cable management and termination quality
Compliance with local safety standards

Sub categories

Showing Results for Accessories

Compare

Add to Cart The item has been added
Speco Technologies

SKU: SO-PMT1

Speco Technologies SO-PMT1 Adjustable Pole Mount

Pole mount with tilt & rotation for Speco cameras in open-air sites
- Fits 2–4 inch diameter steel or aluminum poles without wall penetration
- Tilt and rotation adjustment fine-tunes camera angle during installation
- Outdoor-rated construction with standard fasteners, no specialized tools
In stock · Ships same business day

$85.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Speco Technologies

SKU: SP30PT

Speco Technologies SP30PT 30W Pendant Speaker

30W pendant speaker for intercom and announcements in commercial spaces
- 30W RMS output with 5-inch driver optimized for speech clarity
- Pendant mount with hanging chain for flexible ceiling installation
- 8-ohm impedance rated for indoor, climate-controlled facilities
In stock · Ships same business day

$207.30 $89.99 Save $117.31

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Speco Technologies

SKU: SP30PTB

Speco Technologies SP30PTB 30W Pendant Speaker

30W ceiling pendant speaker for multi-zone commercial audio systems
- 30 watts RMS with 5-inch woofer covers 2,000–4,000 sq ft per zone
- Constant-voltage or low-impedance input integrates with zone amplifiers
- Factory-installed pendant mount suspends from drop ceilings without brackets
In stock · Ships same business day

$96.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Speco Technologies

SKU: SP4AWET

Speco Technologies SP4AWET 4-Inch Outdoor 70V Speaker

4-inch outdoor 70V speaker for extended cable runs and multi-zone PA
- 70V transformer supports 50+ feet per channel without signal loss or upsized wire
- Weather-sealed powder-coated enclosure rated for outdoor use in all conditions
- Wall and surface mount design integrates into security and campus audio systems
In stock · Ships same business day

$154.50 $64.99 Save $89.51

Add to Cart
The item has been added
Compare

Out of stock
Speco Technologies

SKU: SPCBC5

Speco Technologies SPCBC5 5.25" Compression Molded Dual Cone In-C

5.25" dual cone in-ceiling pair for voice and alarm coverage
- Compression molded construction resists warping in standard ceiling cavities
- Dual cone design optimizes midrange clarity for announcements and alarm tones
- 8 ohm impedance with standard mounting brackets for quick integration
Special Order · Ships in 2-3 weeks

$60.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Speco Technologies

SKU: SPCOAX2

Speco Technologies SPCOAX2 Coaxial Video Surge Protector

Passive coaxial surge protection for TVI/CVI/AHD/960H—no power needed
- Inline BNC installation protects camera and recorder from voltage spikes
- Works across TVI, CVI, AHD, and 960H without reconfiguration or swaps
- Passive voltage clamping requires zero external power or active components
In stock · Ships same business day

$56.00 $32.99 Save $23.01

Add to Cart
The item has been added
Compare

Out of stock
Speco Technologies

SKU: SPIPW15A

Speco Technologies SPIPW15A 15W SIP Wall Mountable IP Speaker

15W wall-mount IP speaker with PoE for SIP VoIP systems
- 15W audio output over standard IP networks via SIP protocol
- PoE-powered wall mount eliminates separate power infrastructure
- Compatible with SIP-based VoIP and IP communication platforms
Special Order · Ships in 2-3 weeks

$957.30 $380.99 Save $576.31

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Speco Technologies

SKU: T7010

Speco Technologies T7010 10W 70V Line Transformer

10W 70V line transformer for commercial audio over 100+ feet
- Converts 4–8 ohm amplifier output to 70V line, eliminating signal loss on long runs
- 10W capacity supports multiple 70V speakers across medium-to-large facilities
- Passive design requires no external power; mounts on wall, ceiling, or in rack
In stock · Ships same business day

$29.50 $10.99 Save $18.51

Add to Cart
The item has been added
Compare

Out of stock
Speco Technologies

SKU: T7020

Speco Technologies T7020 20W 70V Line Transformer

20W 70V line transformer for commercial audio distribution
- 20W continuous power handling for medium to large installation zones
- Passive design requires no external power supply or additional wiring
- Multiple taps support flexible wattage allocation across speaker zones
Special Order · Ships in 2-3 weeks

$19.99

Add to Cart
The item has been added
Compare

Out of stock
Speco Technologies

SKU: T70255

Speco Technologies T70255 5W 70/25V Dual Transformer

5W dual transformer for mixed 70V/25V speaker systems
- Supports both 70V and 25V configurations in single unit
- Passive design requires no external power supply
- Compact form factor fits wall, ceiling, or rack mounting
Special Order · Ships in 2-3 weeks

$13.99

Add to Cart
The item has been added
Compare

Out of stock
Speco Technologies

SKU: TMLFLR

Speco Technologies TMLFLR Floor Stand

Floor stand for flexible indoor camera positioning without wall mounting
- Stable base construction supports standard camera interfaces for rapid deployment
- Portable design enables quick repositioning across temporary and semi-permanent sites
- 72-inch height reaches optimal sightlines in retail, warehouse, and event spaces
Special Order · Ships in 2-3 weeks

$631.50 $273.99 Save $357.51

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Speco Technologies

SKU: TVIHD

Speco Technologies TVIHD TVI to HDMI Converter

TVI to HDMI converter for legacy cameras on modern displays
- Converts TVI video signal to HDMI output without external power
- Plug-and-play operation—no network setup or configuration needed
- Compact form factor (3.5 x 5.1 x 1.2 in) fits tight spaces and mobile rigs
In stock · Ships same business day

$283.00 $111.99 Save $171.01

Add to Cart
The item has been added
Compare

Out of stock
Speco Technologies

SKU: VF5100DC

Speco Technologies VF5100DC 5-100mm Auto Iris Lens CS Mount

20x zoom varifocal lens with auto iris for CS-mount cameras
- 5-100mm focal length covers wide to narrow fields of view
- Auto iris maintains exposure across changing lighting conditions
- Direct fit for CS-mount surveillance and IP camera systems
Special Order · Ships in 2-3 weeks

$77.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Speco Technologies

SKU: VGABNC

Speco Technologies VGABNC VGA to Video Connector

VGA to video connector with ONVIF Profile I for IP surveillance
- Converts VGA output to video for legacy and hybrid system integration
- DC 5V operation with AC/DC power flexibility for existing installations
- ONVIF Profile I certified for third-party video management compatibility
In stock · Ships same business day

$217.00 $77.99 Save $139.01

Add to Cart
The item has been added
Compare

Out of stock
Speco Technologies

SKU: VGAHD2

Speco Technologies VGAHD2 VGA to HDMI Converter

VGA to HDMI converter for legacy video to modern displays
- Converts analog VGA input to digital HDMI output, no software needed
- Compact 0.37 lb form factor fits wall-mount, rack, or portable setups
- Operates 30°F to 131°F, suitable for control rooms and equipment enclosures
Special Order · Ships in 2-3 weeks

$263.30 $103.99 Save $159.31

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Speco Technologies

SKU: VID2412CONV

Speco Technologies VID2412CONV 24VAC to 12VDC Power Converter

24VAC to 12VDC converter for CCTV auxiliary loads up to 500mA
- Regulated 12VDC output maintains stable voltage under load for motors and IR
- Compact 0.9 oz form factor mounts on DIN rail or inside enclosures
- Converts standard 24VAC system voltage—no external supply needed at remote sites
In stock · Ships same business day

$36.30 $19.99 Save $16.31

Add to Cart
The item has been added

What to Look For When Buying

The six decisions that matter most before you spec.

Match Bracket to Camera + Surface

A dome camera mounted on a textured wall needs a wall-mount adapter with a gasket; mounted on a pole it needs a pole-mount arm; mounted on an eave it may need a pendant. Third-party brackets exist but brand-specific brackets include proper camera cable routing and weather gasketing. Buying a $40 generic bracket to save on a $80 Axis bracket usually costs more in installation time.

Enclosure NEMA Rating

NEMA 3R = light rain; NEMA 4 = splash + driving rain; NEMA 4X = above + corrosion resistance (coastal, industrial); NEMA 6 = temporary submersion. For weather-exposed camera enclosures, NEMA 4X is the commercial standard. For mission-critical outdoor gear, pair NEMA 4X enclosure + IP67 camera + IK10 vandal rating.

C/CS-Mount Lens Selection

Box cameras use interchangeable C-mount (17.526mm flange) or CS-mount (12.5mm flange). Lens focal length + sensor size determines field of view: a 4mm lens on a 1/3" sensor gives ~60° horizontal FOV. Our DORI guide covers lens selection by scene distance. F-stop matters for low-light; P-iris for auto-exposure.

IR Illuminator Wavelength

850nm IR is more efficient but produces a faint visible red glow (deterrent or accidental giveaway, depending on use case). 940nm is truly covert but requires ~2x the power for the same effective range, and many cameras have lower sensitivity at 940nm. Match illuminator wavelength to camera IR-cut filter spec, or image washout results.

Power Supply Sizing & Distance

12VDC cameras at 100ft from a power supply drop significant voltage over 18-gauge wire — a camera rated for 12V may see 10.5V at the camera end under load, triggering brownout resets. For long runs, use a higher-voltage power supply (24VAC or 48VDC) and step down at the camera. UL-listed surveillance power supplies (Altronix) publish voltage-drop tables.

Cable Jacket Rating

Indoor Cat6 is rated CM (communications); plenum-rated CMP is required for above-drop-ceiling runs per NFPA 70. Outdoor/direct-burial Ethernet is a different product (CMX, direct-burial gel-filled). Mixing jacket ratings causes code violations and fire inspector rejections. Always spec by run environment, not lowest-cost SKU.

Technology Stack

The specs and acronyms that actually affect outdoor performance.

NEMA vs IP Rating Systems

NEMA is the US enclosure standard (NEMA 1-13); IP is the international standard (IP00-IP68). Rough crosswalk: NEMA 4 ≈ IP66, NEMA 4X ≈ IP66 + corrosion, NEMA 6 ≈ IP67. Some spec sheets list both; when only one is given, the crosswalk is approximate. For coastal, industrial, and food-processing environments, specify NEMA 4X or IP66 + stainless steel.

C-Mount vs CS-Mount Lenses

C-mount: 17.526mm flange focal distance. CS-mount: 12.5mm flange. CS cameras accept both lens types (C lenses need a 5mm adapter ring); C cameras accept only C lenses. Most modern box cameras are CS-mount for lens flexibility. Lens thread is 1-inch × 32 TPI on both.

F-Stop / Iris

F-stop = focal length ÷ aperture diameter. Lower F-stop (wider aperture) means more light, better low-light performance, shallower depth of field. F1.4 is very low-light capable; F1.8 is common commercial spec. P-iris (precise iris) lenses auto-adjust aperture based on scene lighting — reduces over-exposure during day, improves low-light at night.

850nm vs 940nm IR

IR illuminators at 850nm are more energy-efficient and the sensitivity of most camera IR-cut filters peaks here — but 850nm produces a faint visible red glow from the LEDs. 940nm is invisible to human eye but requires ~2x the power or shorter effective range. Many covert-deployment cameras are re-tuned for 940nm sensitivity.

UL-Listed Power Supplies

Underwriters Laboratories listed power supplies meet safety standards for overcurrent, overvoltage, and enclosure isolation. UL 294 specifies additional requirements for access control; UL 603 for security burglary; UL 1310 for Class 2 power. Insurance and code requirements increasingly specify UL-listed supplies — particularly in commercial and institutional installations.

Plenum vs Riser vs PVC Cable

Plenum-rated (CMP) cable uses low-smoke FEP jacket for use above suspended ceilings where smoke spreads through return-air plenums. Riser (CMR) is for vertical shaft runs between floors. PVC (CM) is for open office runs only. Using CM in plenum spaces violates NFPA 70 — costly inspector rejection if caught.

Typical Deployment Scenarios

New Construction Retrofit

Cat6A plenum cable pulled to camera locations with proper service loops, 2-gang electrical boxes at each dome location with weatherproof backbox, Cat6A patch panel at the IDF, UL-listed power supplies for any 12V/24V camera, labeled and tested before cameras are mounted.

Coastal / Corrosive Environment

NEMA 4X stainless-steel enclosures for outdoor cameras, 316-grade stainless brackets, silicone dielectric grease on every connector, hot-dipped galvanized or powder-coated steel poles. Budget 15-25% more on accessories vs. standard outdoor — and plan for 3-5 year inspection cycles rather than 10.

Box-Camera LPR Application

Box camera with 50-150mm telephoto lens, dedicated 850nm IR illuminator at same height as camera, pole-mount bracket with junction box, UL power supply for camera + illuminator. LPR-specific enclosures with anti-reflective glass to avoid nighttime IR bloom. Typical deployment: dedicated lane camera, not general-purpose surveillance.

Parking Garage Retrofit

Existing analog coax cable replaced via NVT Phybridge or similar PoE-over-coax, vandal-resistant dome enclosures at ground level, low-profile bullet cameras on ceiling, LED-plus-IR-compatible illuminators to handle harsh fluorescent lighting. Enclosures rated for vehicle-exhaust environment.

Frequently Asked Questions

Do I need the OEM bracket for my camera, or will a generic bracket work?

For most commercial installations, specify the OEM bracket. Brand-specific brackets include proper cable routing, gasketed weather seals, and mounting-hole patterns matched to the camera — which matters more than the cost savings of a generic bracket. Generic brackets are acceptable for indoor standard-dome cameras on flat surfaces; for outdoor, vandal-rated, or pendant applications, use OEM.

What NEMA rating do I need for outdoor camera enclosures?

NEMA 4 for most weather-exposed deployments (driving rain, snow). NEMA 4X for coastal, industrial, or food-processing environments (adds corrosion resistance — typically stainless steel or fiberglass construction). NEMA 6 for temporary submersion or flood-prone areas. The IP-rating equivalent is IP66 for NEMA 4, IP66 + corrosion for NEMA 4X, IP67 for NEMA 6.

How do I choose the right lens focal length for a box camera?

Work backward from the scene. Identify the farthest point you need identification-grade coverage, use our DORI guide to calculate required pixels-per-foot at that distance, and match lens focal length + sensor size to deliver that PPF. A 4mm lens on a 1/3" sensor covers ~60° horizontal FOV; a 12mm lens on the same sensor covers ~20°. Wide FOV = shorter identification distance.

What's the difference between 850nm and 940nm IR illuminators?

850nm is more energy-efficient — you get more effective range per watt — but produces a faint visible red glow from the LEDs. 940nm is truly invisible to the human eye but requires about 2x the power for equivalent range, and many cameras have lower sensor sensitivity at 940nm. For deterrent visibility or cost-efficient long-range, 850nm; for covert applications, 940nm.

Can I power an IP camera with a generic 12V wall-wart?

Not for a commercial deployment. Generic wall-warts are unregulated, not UL-listed for security applications, and typically don't include surge protection. Use a UL-listed surveillance power supply (Altronix AL series, UL 294 or UL 603) with battery backup where required. PoE is preferred when possible — single cable, centralized power management, UPS-backed.

What cable jacket rating do I need for in-ceiling runs?

Plenum-rated (CMP) cable is required for any run through a return-air plenum space above suspended ceilings (most commercial buildings). Riser (CMR) for vertical shafts between floors. PVC (CM) for open office spaces only. Using non-plenum cable in a plenum space is a fire-code violation under NFPA 70 and will be rejected by inspectors. Budget plenum cable for any building where you're not 100% sure of the return-air path.

Accessories

Deployment Considerations

Sub categories

Showing Results for Accessories

Speco Technologies SO-PMT1 Adjustable Pole Mount

Speco Technologies SP30PT 30W Pendant Speaker

Speco Technologies SP30PTB 30W Pendant Speaker

Speco Technologies SP4AWET 4-Inch Outdoor 70V Speaker

Speco Technologies SPCBC5 5.25" Compression Molded Dual Cone In-C

Speco Technologies SPCOAX2 Coaxial Video Surge Protector

Speco Technologies SPIPW15A 15W SIP Wall Mountable IP Speaker

Speco Technologies T7010 10W 70V Line Transformer

Speco Technologies T7020 20W 70V Line Transformer

Speco Technologies T70255 5W 70/25V Dual Transformer

Speco Technologies TMLFLR Floor Stand

Speco Technologies TVIHD TVI to HDMI Converter

Speco Technologies VF5100DC 5-100mm Auto Iris Lens CS Mount

Speco Technologies VGABNC VGA to Video Connector

Speco Technologies VGAHD2 VGA to HDMI Converter

Speco Technologies VID2412CONV 24VAC to 12VDC Power Converter

Browse by Product Family

What to Look For When Buying

Technology Stack

Typical Deployment Scenarios

Top Brands for Outdoor Deployments

Frequently Asked Questions

Related Categories

Engineering Reading