IP Camera Accessories | Mounts, Enclosures, Lenses, IR & Power

Deployment Considerations

Environmental protection and weather resistance
Mounting stability and load support
Power and voltage compatibility
Cable management and termination quality
Compliance with local safety standards

Sub categories

Showing Results for Accessories

Compare

Out of stock
Pelco

SKU: IJTV-AP

Pelco IJTV-AP Adapter Plate for IJV ITV Sarix Cameras

OEM adapter plate for Pelco IJV, ITV, and Sarix Value cameras
- Standardized mounting interface unifies three camera series in one deployment
- NDAA Section 889 compliant for government and regulated facility installations
- Reduces inventory complexity across mixed Pelco camera system rollouts
Special Order · Ships in 2-3 weeks

$33.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Pelco

SKU: IMD1-INC

Pelco IMD1-INC In-Ceiling Mount for Sarix Multi

Flush in-ceiling mount for Sarix Multi IMD1 dome cameras
- Recessed mounting integrates into drop ceilings with optional CLPNL panels
- Mechanical interface locks camera body without power or electronic binding
- Purpose-built for IMD1 form factor only—confirm camera compatibility first
In stock · Ships same business day

$133.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Pelco

SKU: IMD1-INCLD0

Pelco IMD1-INCLD0 Smoked Lower Dome for Sarix

Smoked lower dome for Sarix ceiling cameras; obscures lens orientation
- Smoked tint hides sensor aiming angle from below; prevents blind-spot detection
- PoE++ powered; integrates directly with Sarix multi-directional in-ceiling systems
- IK10 vandal rated; trade-off reduces IR range and low-light sensitivity vs. clear dome
In stock · Ships same business day

$77.55 $57.99 Save $19.56

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Pelco

SKU: IMD1-INCLD1

Pelco IMD1-INCLD1 Clear Lower Dome for Sarix Multi-Directional Cameras

Clear polycarbonate lower dome for Sarix multi-directional cameras
- IK10 vandal rating withstands 20J impact in high-traffic areas
- IR-optimized at 850nm for full night vision range without tint loss
- Fits Pelco Sarix in-ceiling camera systems with maximum light transmission
In stock · Ships same business day

$57.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Pelco

SKU: IMD1-IR

Pelco IMD1-IR 850nm IR Ring Illuminator for Sarix

850nm IR ring illuminator for Sarix Multi-Imager low-light surveillance
- 850nm infrared wavelength with IK10 vandal rating for 24/7 perimeter monitoring
- Ring mount aligns IR output directly with camera FOV; PoE++ powered, no brackets
- Integrates natively with Sarix housing; ONVIF compatible, TAA/NDAA compliant
In stock · Ships same business day

$265.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Pelco

SKU: IMD1-PMT

Pelco IMD1-PMT Outdoor Pendant Mount Adapter

Pendant mount adapter for Sarix Multi IMD1 cameras in outdoor installations
- Mounts IMD1 cameras to WLMT-1001 or NPTA-1001 pendant arms overhead
- Outdoor-rated construction handles temperature swings and corrosion
- IK10 vandal rating with vibration-resistant threaded connection
In stock · Ships same business day

$129.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Pelco

SKU: IMD1-SMT

Pelco IMD1-SMT Surface Mount Adapter for Sarix Multi

Direct surface mount adapter for Pelco Sarix Multi IMD1 domes
- Mounts flat to walls or ceilings without pendant arms or recessed housing
- PoE++ passthrough powers IMD1 camera with full Ethernet and USB connectivity
- NDAA Section 889 compliant for U.S. government and federal procurement
In stock · Ships same business day

$193.99

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: IMD1-SPLD0 RB

Pelco IMD1-SPLD0 RB Smoked Dome Replacement

Smoked dome replacement for Pelco Sarix Multi with IR pass-through
- IK09 impact-rated smoked polycarbonate obscures lens direction
- Maintains IR transmission for 24/7 night vision operation
- Genuine OEM part for Sarix Multi surface and pendant mounts
Special Order · Ships in 2-3 weeks

$87.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Pelco

SKU: IMD1-SPLD0

Pelco IMD1-SPLD0 Smoked Dome Sarix Multi Pendant

Smoked dome for Sarix Multi pendant cameras with IK10 vandal rating
- Amber-tinted polycarbonate obscures sensor direction while maintaining IR transmission
- IK10 rating withstands 5 kg steel ball drops from 1.25 m without penetration
- PoE++ powered; compatible with Pelco Sarix Multi surface-mount and pendant models
In stock · Ships same business day

$129.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Pelco

SKU: IMD1-SPLD1

Pelco IMD1-SPLD1 Clear Dome for Sarix Multi Surface Cameras

Clear dome for Sarix Multi Pro cameras; IK10 rated, max IR pass-through
- IK10 vandal rating withstands 20-joule direct impact without cracking
- Optical-grade clear dome maximizes 850nm IR transmission for night imaging
- Works with 1/2.8" CMOS sensor; supports 0.018 lux low-light performance
In stock · Ships same business day

$129.99

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: IMF-INSTKT

Pelco IMF-INSTKT Surface Mount Fisheye Install Kit

Surface-mount installation kit for Pelco IMF fisheye cameras
- Complete OEM hardware and seals for proper alignment and IP66 sealing
- Includes all consumables needed for fisheye camera installation
- NDAA Section 889 compliant for government and regulated deployments
Special Order · Ships in 2-3 weeks

$21.99

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: IMF-LD1

Pelco IMF-LD1 Clear Lower Dome 3-Pack

Clear replacement dome 3-pack for Pelco IMF fisheye cameras
- Optical-grade dome transmits visible light and infrared for 24/7 panoramic coverage
- 3-pack enables scheduled maintenance and emergency replacement on 360° systems
- Compatible with Pelco IMF Series fisheye camera systems
Special Order · Ships in 2-3 weeks

$110.19 $81.99 Save $28.20

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: IMF-PNL

Pelco IMF-PNL 2x2ft Ceiling Panel Fisheye White

2x2ft reinforced metal ceiling panel for Pelco IMF fisheye cameras
- Precision cutout designed for flush in-ceiling mounting of IMF Series fisheye cameras
- Reinforced metal construction supports camera weight in standard T-bar drop ceilings
- Pantone 427C white finish integrates with commercial office and facility ceilings
Special Order · Ships in 2-3 weeks

$166.95 $122.99 Save $43.96

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: IMJTV-JB

Pelco IMJTV-JB Junction Box for Sarix Value

Junction box for Sarix Value IMV, IJV, ITV cameras with PoE termination
- Works with three Sarix Value form factors—minidome, turret, and dome
- Structured cable entry and termination for organized professional installations
- NDAA Section 889 compliant for government and regulated deployments
Special Order · Ships in 2-3 weeks

$104.62 $76.99 Save $27.63

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Pelco

SKU: IMV-AP

Pelco IMV-AP Adapter Plate for Sarix Minidome

Adapter plate for Sarix minidome varifocal lens upgrades
- Precision-engineered mounting for IMV Series varifocal lenses
- IK09 vandal rating compatible with Sarix Value minidome systems
- Maintains optical alignment for consistent image sharpness across zoom
In stock · Ships same business day

$31.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Pelco

SKU: IMV-PA

Pelco IMV-PA Pendant Mount Adapter for Sarix Value Minidomes

Pendant mount adapter converts Sarix Value minidomes for drop-rod installation
- PoE++ pass-through powers camera on pendant arm or conduit drop
- Converts surface-mount minidomes to pendant configuration for high-ceiling spaces
- NDAA Section 889 compliant, IK10 vandal-rated housing in white finish
In stock · Ships same business day

$40.07 $28.99 Save $11.08

Add to Cart
The item has been added

What to Look For When Buying

The six decisions that matter most before you spec.

Match Bracket to Camera + Surface

A dome camera mounted on a textured wall needs a wall-mount adapter with a gasket; mounted on a pole it needs a pole-mount arm; mounted on an eave it may need a pendant. Third-party brackets exist but brand-specific brackets include proper camera cable routing and weather gasketing. Buying a $40 generic bracket to save on a $80 Axis bracket usually costs more in installation time.

Enclosure NEMA Rating

NEMA 3R = light rain; NEMA 4 = splash + driving rain; NEMA 4X = above + corrosion resistance (coastal, industrial); NEMA 6 = temporary submersion. For weather-exposed camera enclosures, NEMA 4X is the commercial standard. For mission-critical outdoor gear, pair NEMA 4X enclosure + IP67 camera + IK10 vandal rating.

C/CS-Mount Lens Selection

Box cameras use interchangeable C-mount (17.526mm flange) or CS-mount (12.5mm flange). Lens focal length + sensor size determines field of view: a 4mm lens on a 1/3" sensor gives ~60° horizontal FOV. Our DORI guide covers lens selection by scene distance. F-stop matters for low-light; P-iris for auto-exposure.

IR Illuminator Wavelength

850nm IR is more efficient but produces a faint visible red glow (deterrent or accidental giveaway, depending on use case). 940nm is truly covert but requires ~2x the power for the same effective range, and many cameras have lower sensitivity at 940nm. Match illuminator wavelength to camera IR-cut filter spec, or image washout results.

Power Supply Sizing & Distance

12VDC cameras at 100ft from a power supply drop significant voltage over 18-gauge wire — a camera rated for 12V may see 10.5V at the camera end under load, triggering brownout resets. For long runs, use a higher-voltage power supply (24VAC or 48VDC) and step down at the camera. UL-listed surveillance power supplies (Altronix) publish voltage-drop tables.

Cable Jacket Rating

Indoor Cat6 is rated CM (communications); plenum-rated CMP is required for above-drop-ceiling runs per NFPA 70. Outdoor/direct-burial Ethernet is a different product (CMX, direct-burial gel-filled). Mixing jacket ratings causes code violations and fire inspector rejections. Always spec by run environment, not lowest-cost SKU.

Technology Stack

The specs and acronyms that actually affect outdoor performance.

NEMA vs IP Rating Systems

NEMA is the US enclosure standard (NEMA 1-13); IP is the international standard (IP00-IP68). Rough crosswalk: NEMA 4 ≈ IP66, NEMA 4X ≈ IP66 + corrosion, NEMA 6 ≈ IP67. Some spec sheets list both; when only one is given, the crosswalk is approximate. For coastal, industrial, and food-processing environments, specify NEMA 4X or IP66 + stainless steel.

C-Mount vs CS-Mount Lenses

C-mount: 17.526mm flange focal distance. CS-mount: 12.5mm flange. CS cameras accept both lens types (C lenses need a 5mm adapter ring); C cameras accept only C lenses. Most modern box cameras are CS-mount for lens flexibility. Lens thread is 1-inch × 32 TPI on both.

F-Stop / Iris

F-stop = focal length ÷ aperture diameter. Lower F-stop (wider aperture) means more light, better low-light performance, shallower depth of field. F1.4 is very low-light capable; F1.8 is common commercial spec. P-iris (precise iris) lenses auto-adjust aperture based on scene lighting — reduces over-exposure during day, improves low-light at night.

850nm vs 940nm IR

IR illuminators at 850nm are more energy-efficient and the sensitivity of most camera IR-cut filters peaks here — but 850nm produces a faint visible red glow from the LEDs. 940nm is invisible to human eye but requires ~2x the power or shorter effective range. Many covert-deployment cameras are re-tuned for 940nm sensitivity.

UL-Listed Power Supplies

Underwriters Laboratories listed power supplies meet safety standards for overcurrent, overvoltage, and enclosure isolation. UL 294 specifies additional requirements for access control; UL 603 for security burglary; UL 1310 for Class 2 power. Insurance and code requirements increasingly specify UL-listed supplies — particularly in commercial and institutional installations.

Plenum vs Riser vs PVC Cable

Plenum-rated (CMP) cable uses low-smoke FEP jacket for use above suspended ceilings where smoke spreads through return-air plenums. Riser (CMR) is for vertical shaft runs between floors. PVC (CM) is for open office runs only. Using CM in plenum spaces violates NFPA 70 — costly inspector rejection if caught.

Typical Deployment Scenarios

New Construction Retrofit

Cat6A plenum cable pulled to camera locations with proper service loops, 2-gang electrical boxes at each dome location with weatherproof backbox, Cat6A patch panel at the IDF, UL-listed power supplies for any 12V/24V camera, labeled and tested before cameras are mounted.

Coastal / Corrosive Environment

NEMA 4X stainless-steel enclosures for outdoor cameras, 316-grade stainless brackets, silicone dielectric grease on every connector, hot-dipped galvanized or powder-coated steel poles. Budget 15-25% more on accessories vs. standard outdoor — and plan for 3-5 year inspection cycles rather than 10.

Box-Camera LPR Application

Box camera with 50-150mm telephoto lens, dedicated 850nm IR illuminator at same height as camera, pole-mount bracket with junction box, UL power supply for camera + illuminator. LPR-specific enclosures with anti-reflective glass to avoid nighttime IR bloom. Typical deployment: dedicated lane camera, not general-purpose surveillance.

Parking Garage Retrofit

Existing analog coax cable replaced via NVT Phybridge or similar PoE-over-coax, vandal-resistant dome enclosures at ground level, low-profile bullet cameras on ceiling, LED-plus-IR-compatible illuminators to handle harsh fluorescent lighting. Enclosures rated for vehicle-exhaust environment.

Frequently Asked Questions

Do I need the OEM bracket for my camera, or will a generic bracket work?

For most commercial installations, specify the OEM bracket. Brand-specific brackets include proper cable routing, gasketed weather seals, and mounting-hole patterns matched to the camera — which matters more than the cost savings of a generic bracket. Generic brackets are acceptable for indoor standard-dome cameras on flat surfaces; for outdoor, vandal-rated, or pendant applications, use OEM.

What NEMA rating do I need for outdoor camera enclosures?

NEMA 4 for most weather-exposed deployments (driving rain, snow). NEMA 4X for coastal, industrial, or food-processing environments (adds corrosion resistance — typically stainless steel or fiberglass construction). NEMA 6 for temporary submersion or flood-prone areas. The IP-rating equivalent is IP66 for NEMA 4, IP66 + corrosion for NEMA 4X, IP67 for NEMA 6.

How do I choose the right lens focal length for a box camera?

Work backward from the scene. Identify the farthest point you need identification-grade coverage, use our DORI guide to calculate required pixels-per-foot at that distance, and match lens focal length + sensor size to deliver that PPF. A 4mm lens on a 1/3" sensor covers ~60° horizontal FOV; a 12mm lens on the same sensor covers ~20°. Wide FOV = shorter identification distance.

What's the difference between 850nm and 940nm IR illuminators?

850nm is more energy-efficient — you get more effective range per watt — but produces a faint visible red glow from the LEDs. 940nm is truly invisible to the human eye but requires about 2x the power for equivalent range, and many cameras have lower sensor sensitivity at 940nm. For deterrent visibility or cost-efficient long-range, 850nm; for covert applications, 940nm.

Can I power an IP camera with a generic 12V wall-wart?

Not for a commercial deployment. Generic wall-warts are unregulated, not UL-listed for security applications, and typically don't include surge protection. Use a UL-listed surveillance power supply (Altronix AL series, UL 294 or UL 603) with battery backup where required. PoE is preferred when possible — single cable, centralized power management, UPS-backed.

What cable jacket rating do I need for in-ceiling runs?

Plenum-rated (CMP) cable is required for any run through a return-air plenum space above suspended ceilings (most commercial buildings). Riser (CMR) for vertical shafts between floors. PVC (CM) for open office spaces only. Using non-plenum cable in a plenum space is a fire-code violation under NFPA 70 and will be rejected by inspectors. Budget plenum cable for any building where you're not 100% sure of the return-air path.

Accessories

Deployment Considerations

Sub categories

Showing Results for Accessories

Pelco IJTV-AP Adapter Plate for IJV ITV Sarix Cameras

Pelco IMD1-INC In-Ceiling Mount for Sarix Multi

Pelco IMD1-INCLD0 Smoked Lower Dome for Sarix

Pelco IMD1-INCLD1 Clear Lower Dome for Sarix Multi-Directional Cameras

Pelco IMD1-IR 850nm IR Ring Illuminator for Sarix

Pelco IMD1-PMT Outdoor Pendant Mount Adapter

Pelco IMD1-SMT Surface Mount Adapter for Sarix Multi

Pelco IMD1-SPLD0 RB Smoked Dome Replacement

Pelco IMD1-SPLD0 Smoked Dome Sarix Multi Pendant

Pelco IMD1-SPLD1 Clear Dome for Sarix Multi Surface Cameras

Pelco IMF-INSTKT Surface Mount Fisheye Install Kit

Pelco IMF-LD1 Clear Lower Dome 3-Pack

Pelco IMF-PNL 2x2ft Ceiling Panel Fisheye White

Pelco IMJTV-JB Junction Box for Sarix Value

Pelco IMV-AP Adapter Plate for Sarix Minidome

Pelco IMV-PA Pendant Mount Adapter for Sarix Value Minidomes

Browse by Product Family

What to Look For When Buying

Technology Stack

Typical Deployment Scenarios

Top Brands for Outdoor Deployments

Frequently Asked Questions

Related Categories

Engineering Reading

Certified Experts

Manufacturer Authorized

Expert Access

Since 2014

Brands

Categories

IP Cameras

Ordering

Legal

Company

Sales & Expert Advice

Customer Service