Refine by

No filters applied

Door Locks & Strikes

Electric strikes and electromechanical locks for access-controlled doors. Available in fail-safe and fail-secure configurations with ANSI/BHMA-rated durability for high-traffic commercial entry points.

Plan Your Deployment

Match strike to door frame material and latch bolt geometry
Confirm fail-safe or fail-secure mode per fire and building code
Specify voltage and current draw for power supply sizing
Evaluate weather-sealed models for exterior or parking garage doors

Plan Lock Hardware Browse Access Control

Showing Results for Door Locks & Strikes

Compare

Out of stock
SDC

SKU: 446U

SDC Security Door Controls 446U Momentary DPST Exit Controller

DPST momentary exit controller for 24VDC access systems with OSDP
Special Order · Usually Ships in 2-3 Weeks

$103.99 $99.99 Save $4.00

Add to Cart
The item has been added
Compare

Out of stock
SDC

SKU: 451V

SDC Security Door Controls 451V Vandal Resistant Push Switch

Vandal-resistant 10-door controller with encrypted OSDP for secure access
Special Order · Usually Ships in 2-3 Weeks

$120.99 $116.99 Save $4.00

Add to Cart
The item has been added
Compare

Out of stock
SDC

SKU: 484A2U

SDC Security Door Controls 484A2U Exit Switch Controller

Multi-door controller for 63 exits with 250K credential capacity
Special Order · Usually Ships in 2-3 Weeks

$172.99 $166.99 Save $6.00

Add to Cart
The item has been added
Compare

Out of stock
SDC

SKU: 55-CU

SDC Security Door Controls 55-CU Electric Strike 12/24V

630 lbs electric strike with 12/24V dual voltage for access control
Special Order · Usually Ships in 2-3 Weeks

$342.99 $331.99 Save $11.00

Add to Cart
The item has been added
Compare

Out of stock
SDC

SKU: BB1D

SDC Security Door Controls BB1D Retrofit Back Box

OSDP retrofit controller for NFC proximity readers in existing installations
Special Order · Usually Ships in 2-3 Weeks

$11.99

Add to Cart
The item has been added
Compare

Out of stock
SDC

SKU: CR4

SDC Security Door Controls CR4 4-Door Control Board

4-door access control board with 250K credentials over OSDP
Special Order · Usually Ships in 2-3 Weeks

$129.99 $125.99 Save $4.00

Add to Cart
The item has been added
Compare

Out of stock
SDC

SKU: E6200

SDC Security Door Controls E6200 Excel Industrial Series

Industrial lock/strike with 3-in-1 credential reader and OSDP control
Special Order · Usually Ships in 2-3 Weeks

$343.99 $332.99 Save $11.00

Add to Cart
The item has been added
Compare

Out of stock
SDC

SKU: E6U

SDC Security Door Controls E6U Class Door Kit Reader

NFC + keypad reader for SDC E600 glass door systems with OSDP
Special Order · Usually Ships in 2-3 Weeks

$99.99 $96.99 Save $3.00

Add to Cart
The item has been added
Compare

Out of stock
SDC

SKU: E75PSQE1Q

SDC Security Door Controls E75PSQE1Q Keypad Lock/Strike

Keypad lock/strike for 2 doors, supports 250K users with multiple credential types
Special Order · Usually Ships in 2-3 Weeks

$839.99 $812.99 Save $27.00

Add to Cart
The item has been added
Compare

Out of stock
SDC

SKU: EH101224A

SDC Security Door Controls EH101224A Flush Mount Strike

Flush-mount strike for multi-credential access control up to 10 doors
Special Order · Usually Ships in 2-3 Weeks

$117.99

Add to Cart
The item has been added
Compare

Out of stock
SDC

SKU: EH1024120A

SDC Security Door Controls EH1024120A EH10 Flush Lock/Strike

Flush lock/strike for networked access control up to 10 doors
Special Order · Usually Ships in 2-3 Weeks

$108.99 $104.99 Save $4.00

Add to Cart
The item has been added
Compare

Out of stock
SDC

SKU: EP499-R

SDC Security Door Controls EP499-R Explosion Proof Controller

Explosion-proof 4-door controller for hazardous industrial locations
Special Order · Usually Ships in 2-3 Weeks

$1,881.99 $1,821.99 Save $60.00

Add to Cart
The item has been added
Compare

Out of stock
SDC

SKU: IC-UR48-SPEC

SDC Security Door Controls IC-UR48-SPEC 4-Door Controller

4-door access controller with 250,000 user capacity for multi-door facilities
Special Order · Usually Ships in 2-3 Weeks

$91.99 $88.99 Save $3.00

Add to Cart
The item has been added
Compare

Out of stock
SDC

SKU: LR100ARK

SDC Security Door Controls LR100ARK Electric Latch Retraction

Multi-door controller for 63 doors and 250,000 credentials
Special Order · Usually Ships in 2-3 Weeks

$464.99 $449.99 Save $15.00

Add to Cart
The item has been added
Compare

Out of stock
SDC

SKU: LRY61R

SDC Security Door Controls LRY61R Yale Retrofit Monitoring Kit

Yale retrofit controller for 63 doors with multi-credential support
Special Order · Usually Ships in 2-3 Weeks

$79.99 $76.99 Save $3.00

Add to Cart
The item has been added
Compare

Out of stock
SDC

SKU: MC-4MU

SDC Security Door Controls MC-4MU SPDT Concealed Magnetic

4-door controller with 250K user capacity, OSDP/TCP-IP networked
Special Order · Usually Ships in 2-3 Weeks

$75.99 $73.99 Save $2.00

Add to Cart
The item has been added

Browse by Product Family

Click through to shop the families that fit your door locks & strikes deployment.

Electric Strikes

Retrofit-compatible electric strikes for aluminum and steel frames. Available in fail-safe (unlock on power loss) and fail-secure (lock on power loss) configurations with integrated monitoring.

Electromechanical Locks

Solenoid-actuated and electromagnetic locking mechanisms for glass doors, sliding barriers, and cabinet-grade applications. Direct 12/24V integration.

Fail-Safe Locks

Unlocking on power loss or alarm trigger for emergency egress compliance. NFPA 101 and IBC-compliant for life-safety critical doors.

Fail-Secure Locks

Remain locked on power loss to maintain perimeter security during power events. Ideal for secure entries, server rooms, and restricted zones.

Monitored Door Hardware

Electric strikes and locks with integrated door position sensors, tamper detection, and relay feedback for real-time access event logging.

SDC Electric Locking Solutions

Industry-standard electric strikes and solenoid locks from SDC, engineered for ANSI/BHMA Grade 1 durability in institutional and commercial deployments.

What to Look For When Buying

The decisions that matter most before you spec.

Fail-Safe vs. Fail-Secure: Life Safety vs. Perimeter Security

Fail-safe locks unlock on power loss (required for emergency exits and panic hardware compliance), while fail-secure locks maintain lock status to prevent intrusion during outages. Choose fail-safe for public egress routes and fail-secure for server rooms, vaults, and restricted areas. Control systems integrate both types across a single deployment.

ANSI/BHMA Grade Ratings and Cycle Life Durability

Grade 1 strikes withstand 500,000+ cycles (heavy institutional traffic); Grade 2 handles 300,000+ cycles (mid-traffic commercial). Verify cycle rating against your facility's foot traffic and door-open frequency to avoid premature failure and access denial incidents.

Power Supply Consistency and System Redundancy

Electric strikes and solenoid locks demand stable 12/24V DC power with low ripple. Access hubs and controllers should include UPS-backed power distribution to prevent lock dropout during brownouts. Undersized power budgets cause system failures during critical security events.

Door Frame Material and Strike Compatibility

Aluminum frames, hollow metal doors, and glass-mounted applications require specific strike profiles and mounting depths. Verify frame thickness, latch bolt size, and reinforcement plate compatibility before purchasing to avoid field rework and installation delays.

Monitoring and Event Logging Integration

Monitored strikes with door position sensors and tamper alerts feed real-time events to access control systems for audit trails and security response. Non-monitored passive strikes offer no feedback, increasing blind spots in perimeter visibility and making threat detection reactive instead of preventive.

Local Code Compliance and Third-Party Certification

ANSI/BHMA, UL, and fire-rated certifications vary by jurisdiction and occupancy type. Healthcare, education, and government facilities often mandate specific grades and configurations. Confirm with local authority and consult our experts to avoid code violations and permit delays.

Technology Stack

The specs and acronyms that actually affect door locks & strikes performance.

Fail-Safe / Fail-Secure Operation

Fail-safe unlocks the door on power loss or alarm signal for life-safety egress; fail-secure remains locked to maintain perimeter security. Choose based on occupancy type (public vs. restricted) and local fire/building code requirements. Most deployments use hybrid approaches—fail-safe on main exits, fail-secure on utility areas.

Strike Voltage and Current Draw (12V/24V DC)

Electric strikes typically draw 200–600mA at 12V or 100–300mA at 24V during solenoid actuation. Higher voltage (24V) reduces I²R losses in long cable runs and is preferred for large facilities. Size power supplies and wiring gauge accordingly to prevent voltage sag under full load.

ANSI/BHMA Grade Ratings (1–3)

Grade 1 = 500,000+ cycles, heaviest duty; Grade 2 = 300,000+ cycles, medium commercial; Grade 3 = 100,000+ cycles, light residential. Grade 1 is standard for institutional and high-traffic security installations; lower grades risk premature failure and replacement costs.

Solenoid Latching vs. Momentary Activation

Momentary solenoids require continuous power to hold the lock open and release on de-energization; latching solenoids hold position after one pulse, reducing power consumption. Latching is preferred for battery-backed or remote installations to lower UPS/power-supply load.

Door Position Sensing and Tamper Feedback

Monitored strikes include magnetic reed switches or proximity sensors that signal door open/close state and contact tampering to the access control system. Non-monitored strikes are passive and provide no feedback, limiting audit visibility and threat detection responsiveness.

Reinforcement Plate Installation and Frame Compatibility

Strike plates must be secured to the door frame with through-bolts or wood screws through reinforcement plates to distribute load and prevent kick-in attacks. Aluminum frames and hollow-metal doors require specified plate thickness and bolt patterns; verify dimensions before procurement.

Typical Deployment Scenarios

Mid-Sized Office Building Perimeter (12 Ground-Floor Entries)

Deploy 12 fail-secure SDC electric strikes on main lobbies, server room, and secure offices. Back with a 24V/5A distributed power supply and a door controller managing unlock schedules and monitoring door-position sensors for intrusion alerts. Integrate card readers at each strike for access logging.

Hospital Emergency Department (8 Fail-Safe + 4 Fail-Secure Mixed)

Public egress areas (ER waiting, hallways) use fail-safe strikes for panic compliance; restricted zones (pharmacy, med storage, ICU) use fail-secure. All 12 strikes feed unified control system with UPS-backed power and monitoring. Solenoid latching reduces power draw on battery backup.

School Campus Corridor Lockdown (20 Classrooms + 4 Emergency Exits)

Install fail-secure electromechanical locks on 20 classroom doors with manual override capability; 4 main exits use fail-safe strikes for evacuation. Access hub centralizes release during threat events. See school security design guide for integrated lockdown workflows.

Data Center Secure Entry (6 Cage Doors + Server Room Access)

Six fail-secure solenoid-latching locks on equipment cages and server room doors minimize UPS drain. Monitored strike sensors log every open event for compliance audits. Pair with proximity card readers for multi-factor credential checks and integrate door I/O modules for alarm feedback.

Top Brands for Door Locks & Strikes

Click through to each brand for engineering profile and NDAA compliance status.

SDC

Authorized dealer · browse the full SDC catalog for this category

Ubiquiti

Authorized dealer · browse the full Ubiquiti catalog for this category

Frequently Asked Questions

What's the difference between a fail-safe and fail-secure electric strike?

Fail-safe strikes unlock when power is lost or an alarm is triggered—critical for emergency exits and life-safety compliance. Fail-secure strikes remain locked on power loss to prevent intrusion. Building code and occupancy type determine which you need; most facilities use both: fail-safe on public exits, fail-secure on secure entries and restricted zones.

How do I choose between 12V and 24V electric strikes?

24V systems are preferred for large deployments because they reduce current draw (lower I²R losses), cause less voltage sag in long cable runs, and are safer for wet environments. 12V is acceptable for small, localized installations near the power supply. Always verify your access control panel's output voltage and power budget before selecting strikes.

What ANSI/BHMA grade should I specify for a commercial deployment?

Grade 1 (500,000+ cycles) is industry standard for institutional, government, and high-traffic commercial facilities. Grade 2 (300,000+ cycles) suits mid-traffic office buildings. Grade 3 is rarely used in professional security contexts. Higher grade ensures durability and reduces warranty/replacement risk over a 10+ year lifecycle.

Do I need monitored strikes or can I use passive non-monitored locks?

Monitored strikes with door-position sensors provide real-time open/close events and tamper alerts for audit trails and threat detection. Non-monitored strikes offer no feedback and create blind spots in your access control visibility. For compliance-heavy environments (healthcare, finance, schools), monitored hardware is strongly recommended.

How much power do electric strikes consume, and will my UPS back them up?

Most strikes draw 200–600mA at 12V (2.4–7.2W) or 100–300mA at 24V (2.4–7.2W) during solenoid actuation. Latching solenoids hold position after one pulse and consume less continuous power. Estimate total door count × latching solenoid wattage, add margin, and select a UPS rated for sustained hold-time during outages. Undersized UPS causes lock dropout during power events.

What's the installation process, and do I need a professional integrator?

Strike installation involves mounting the strike plate and reinforcement bracket to the door frame using through-bolts or wood screws, ensuring proper alignment with the latch bolt and frame material. Wiring requires low-voltage DC runs from the power supply and control panel with proper shielding for noise immunity. Professional installation is recommended to avoid frame damage, improper strike orientation, and code violations. Contact our experts for site assessment and integration guidance.

Related Categories

Adjacent equipment that typically ships alongside these products.

Door Hardware & I/O Door Controllers Control Systems Card Readers Access Hubs & Controllers Access Cards & Credentials Credentials

Engineering Reading

Deep-dives from our engineering team on deployment planning.

Why Surveillance Systems Fail During Incidents Why Your NVR Can't Handle Its Rated Camera Count Why Surveillance Networks Collapse at the Core Why Large Surveillance Systems Fail: Storage Throughput Reality Why Surveillance Standards Collapse After the Third Location Why 4K Cameras Fail at Night Why Your PoE Switch Fails After 18 Cameras Frame Rate vs. Reality: When 30 FPS Makes Your System Worse