IP Camera Accessories | Mounts, Enclosures, Lenses, IR & Power

Deployment Considerations

Environmental protection and weather resistance
Mounting stability and load support
Power and voltage compatibility
Cable management and termination quality
Compliance with local safety standards

Sub categories

Showing Results for Accessories

Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-OM-SM-10G-S-2

Ubiquiti UACC-OM-SM-10G-S-2 10 Gbps Single-Mode SFP+ Transceiver

10 Gbps single-mode SFP+ for campus fiber runs 10+ km
- 10 Gbps bidirectional throughput over single-mode SMF-28 fiber
- SFP+ form factor plugs directly into UniFi switches and routers
- Spans 10+ km depending on wavelength and fiber condition
In stock · Ships same business day

$175.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-OM-SM-10G-S-20

Ubiquiti UACC-OM-SM-10G-S-20 10 Gbps Single-Mode SFP+ Transceiver

10 Gbps single-mode SFP+ transceiver for long-distance fiber links
- 10 Gbps bidirectional throughput over single-mode fiber up to 80+ km
- Pluggable SFP+ module swaps into UniFi switches without power interruption
- Passive design draws power from SFP+ slot; no external power required
In stock · Ships same business day

$1,595.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-OM-SM-1G-S-2

Ubiquiti UACC-OM-SM-1G-S-2 Single-Mode Optical Module (2-Pack)

1Gbps single-mode fiber modules for long-distance UniFi links (2-pack)
- 1Gbps bidirectional throughput over single-mode fiber to 10+ km
- LC connectors integrate with compatible UniFi switches for fiber backbone
- 2-pack supplies both transceivers needed for one complete bidirectional link
In stock · Ships same business day

$37.50 $25.99 Save $11.51

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-OM-SM-1G-S-20

Ubiquiti UACC-OM-SM-1G-S-20 1 Gbps Single-Mode Optical Module

1 Gbps single-mode fiber module for UniFi switches, 20+ km reach
- 1 Gbps bidirectional throughput over single-mode fiber (ITU G.652)
- Reaches 20+ km without regeneration; minimal signal loss over distance
- SFP form factor plugs directly into UniFi switches with SFP ports
In stock · Ships same business day

$286.00 $221.99 Save $64.01

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-PANICBAR

Ubiquiti UACC-PANICBAR Single-Latched Emergency Door Panic Bar

Single-latched panic bar with dry relay for any access control system
- Dry relay output (30V DC, 1A) integrates with virtually any platform
- Aluminum and stainless steel construction resists corrosion in wet environments
- UL 305, UL 10C, and CAN/ULC-S132 certified for life-safety compliance
In stock · Ships same business day

$422.99

Add to Cart
The item has been added
Compare

Out of stock
Ubiquiti

SKU: UACC-POE+++-10G

Ubiquiti UACC-POE+++-10G adapter that powers UniFi PoE+++

10G PoE+++ adapter for UniFi devices with remote power injection
- PoE+++ power delivery extends budget beyond switch capacity for remote devices
- Multi-Gigabit LAN connection runs on dedicated adapter line independent of PoE
- Reduces centralized PoE constraints in mixed UniFi network architectures
Special Order · Ships in 2-3 weeks

$77.33 $51.99 Save $25.34

Add to Cart
The item has been added
Compare

Out of stock
Ubiquiti

SKU: UACC-POE++-10G

Ubiquiti UACC-POE++-10G adapter that powers UniFi PoE++ devices

PoE++ adapter with 10G for UniFi devices needing independent power
- PoE++ (802.3bt) power injection independent of your network switch
- Multi-Gigabit 10G Ethernet connection for minimal upstream overhead
- Reduces switch power budget demands in bandwidth-constrained deployments
Special Order · Ships in 2-3 weeks

$67.92 $40.99 Save $26.93

Add to Cart
The item has been added
Compare

Out of stock
Ubiquiti

SKU: UACC-POE+-2.5G

Ubiquiti UACC-POE+-2.5G adapter that powers UniFi PoE+ devices

PoE+ adapter with 2.5G for UniFi devices, offloads switch power
- PoE+ power input with 2.5G Ethernet for independent device feeding
- Reduces load on PoE switches in multi-device UniFi deployments
- Single port adapter designed for access points, cameras, distributed setups
Special Order · Ships in 2-3 weeks

$45.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-POE+-USBC

Ubiquiti UACC-POE+-USBC PoE+ AC Adapter with USB-C Input

USB-C powered PoE+ injector for single UniFi endpoints
- 30W PoE+ (802.3at) output on single RJ-45 port
- AC mains input via USB-C connector for simplified cable routing
- Compact desktop or wall-mount form factor for distributed deployments
In stock · Ships same business day

$51.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-PRO-AP-AM

Ubiquiti UACC-PRO-AP-AM Wall mount for an U6 Pro or AC Pro

Wall mount arm for UniFi U6 Pro and AC Pro access points
- Compact polycarbonate design fits 174 x 189 x 30 mm footprint
- Lightweight 136g mount with included hardware for standard walls
- Positions access points on walls where ceiling install isn't practical
In stock · Ships same business day

$47.52 $25.99 Save $21.53

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-PRO-BULLET-ENHANCER-W

Ubiquiti UACC-PRO-BULLET-ENHANCER-W IR LED & Radar Detection Accessory

IR floodlight + radar motion detection for Ubiquiti bullet cameras
- IR LED illumination extends low-light visibility without white-light activation
- Radar motion sensing works independently of lighting conditions
- Direct-attach design integrates with compatible Ubiquiti bullet camera platforms
In stock · Ships same business day

$240.00 $170.99 Save $69.01

Add to Cart
The item has been added
Compare

Out of stock
Ubiquiti

SKU: UACC-PRO-MAX-16-RM

Ubiquiti UACC-PRO-MAX-16-RM rack-mount accessory

1U rack mount for UniFi Pro Max 16 switch integration
- Steel and polycarbonate construction fits standard 19-inch racks
- Compact 1U form factor at 280.9 x 115.1 x 42.8 mm
- Lightweight 1.1 kg design simplifies installation and handling
Special Order · Ships in 2-3 weeks

$79.00 $51.99 Save $27.01

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-PSU-12V-150W

Ubiquiti UACC-PSU-12V-150W Hot-Swappable Power Module

150W hot-swappable 12V DC module for Enterprise Fortress gateways
- Replace during operation—zero downtime on 24/7 surveillance systems
- 100–240V AC input works globally; 81%+ efficiency cuts cooling load
- 150W @ 12.5A with overvoltage and overcurrent protection built in
In stock · Ships same business day

$184.13 $89.99 Save $94.14

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-PSU-12V-550W

Ubiquiti UACC-PSU-12V-550W Hot-Swappable Power Module

550W hot-swappable PSU for Ubiquiti NVR & enterprise systems
- 12V DC, 45A output supports multi-channel recording with PoE gear
- Live replacement without shutdown—swap failed module in seconds
- 100–240V AC input works globally; compact 185×73.5×40 mm form factor
In stock · Ships same business day

$230.00 $167.99 Save $62.01

Add to Cart
The item has been added
Compare

Out of stock
Ubiquiti

SKU: UACC-PSU-27V-250W

Ubiquiti UACC-PSU-27V-250W 250W AC/DC Power Supply

250W 27V DC supply with hot-swap design for UISP Power Pro
- 27V DC at 9.3A output; 100–240V AC input, 50/60Hz compatible
- Hot-swap capable for live replacement without service interruption
- SECC steel enclosure rated -20 to 50°C for outdoor deployment
Special Order · Ships in 2-3 weeks

$145.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Ubiquiti

SKU: UACC-PSU-UDW

Ubiquiti UACC-PSU-UDW 550W Auxiliary Power Supply Module

550W AC-to-DC auxiliary PSU for Dream Wall N+1 power redundancy
- 550W output at 54.8V DC, 10A max for concurrent failover without voltage sag
- Auto-sensing 100–240V AC input; works globally without configuration or swaps
- Proprietary JYP connector and aluminium/steel build designed for Dream Wall systems
In stock · Ships same business day

$433.99

Add to Cart
The item has been added

What to Look For When Buying

The six decisions that matter most before you spec.

Match Bracket to Camera + Surface

A dome camera mounted on a textured wall needs a wall-mount adapter with a gasket; mounted on a pole it needs a pole-mount arm; mounted on an eave it may need a pendant. Third-party brackets exist but brand-specific brackets include proper camera cable routing and weather gasketing. Buying a $40 generic bracket to save on a $80 Axis bracket usually costs more in installation time.

Enclosure NEMA Rating

NEMA 3R = light rain; NEMA 4 = splash + driving rain; NEMA 4X = above + corrosion resistance (coastal, industrial); NEMA 6 = temporary submersion. For weather-exposed camera enclosures, NEMA 4X is the commercial standard. For mission-critical outdoor gear, pair NEMA 4X enclosure + IP67 camera + IK10 vandal rating.

C/CS-Mount Lens Selection

Box cameras use interchangeable C-mount (17.526mm flange) or CS-mount (12.5mm flange). Lens focal length + sensor size determines field of view: a 4mm lens on a 1/3" sensor gives ~60° horizontal FOV. Our DORI guide covers lens selection by scene distance. F-stop matters for low-light; P-iris for auto-exposure.

IR Illuminator Wavelength

850nm IR is more efficient but produces a faint visible red glow (deterrent or accidental giveaway, depending on use case). 940nm is truly covert but requires ~2x the power for the same effective range, and many cameras have lower sensitivity at 940nm. Match illuminator wavelength to camera IR-cut filter spec, or image washout results.

Power Supply Sizing & Distance

12VDC cameras at 100ft from a power supply drop significant voltage over 18-gauge wire — a camera rated for 12V may see 10.5V at the camera end under load, triggering brownout resets. For long runs, use a higher-voltage power supply (24VAC or 48VDC) and step down at the camera. UL-listed surveillance power supplies (Altronix) publish voltage-drop tables.

Cable Jacket Rating

Indoor Cat6 is rated CM (communications); plenum-rated CMP is required for above-drop-ceiling runs per NFPA 70. Outdoor/direct-burial Ethernet is a different product (CMX, direct-burial gel-filled). Mixing jacket ratings causes code violations and fire inspector rejections. Always spec by run environment, not lowest-cost SKU.

Technology Stack

The specs and acronyms that actually affect outdoor performance.

NEMA vs IP Rating Systems

NEMA is the US enclosure standard (NEMA 1-13); IP is the international standard (IP00-IP68). Rough crosswalk: NEMA 4 ≈ IP66, NEMA 4X ≈ IP66 + corrosion, NEMA 6 ≈ IP67. Some spec sheets list both; when only one is given, the crosswalk is approximate. For coastal, industrial, and food-processing environments, specify NEMA 4X or IP66 + stainless steel.

C-Mount vs CS-Mount Lenses

C-mount: 17.526mm flange focal distance. CS-mount: 12.5mm flange. CS cameras accept both lens types (C lenses need a 5mm adapter ring); C cameras accept only C lenses. Most modern box cameras are CS-mount for lens flexibility. Lens thread is 1-inch × 32 TPI on both.

F-Stop / Iris

F-stop = focal length ÷ aperture diameter. Lower F-stop (wider aperture) means more light, better low-light performance, shallower depth of field. F1.4 is very low-light capable; F1.8 is common commercial spec. P-iris (precise iris) lenses auto-adjust aperture based on scene lighting — reduces over-exposure during day, improves low-light at night.

850nm vs 940nm IR

IR illuminators at 850nm are more energy-efficient and the sensitivity of most camera IR-cut filters peaks here — but 850nm produces a faint visible red glow from the LEDs. 940nm is invisible to human eye but requires ~2x the power or shorter effective range. Many covert-deployment cameras are re-tuned for 940nm sensitivity.

UL-Listed Power Supplies

Underwriters Laboratories listed power supplies meet safety standards for overcurrent, overvoltage, and enclosure isolation. UL 294 specifies additional requirements for access control; UL 603 for security burglary; UL 1310 for Class 2 power. Insurance and code requirements increasingly specify UL-listed supplies — particularly in commercial and institutional installations.

Plenum vs Riser vs PVC Cable

Plenum-rated (CMP) cable uses low-smoke FEP jacket for use above suspended ceilings where smoke spreads through return-air plenums. Riser (CMR) is for vertical shaft runs between floors. PVC (CM) is for open office runs only. Using CM in plenum spaces violates NFPA 70 — costly inspector rejection if caught.

Typical Deployment Scenarios

New Construction Retrofit

Cat6A plenum cable pulled to camera locations with proper service loops, 2-gang electrical boxes at each dome location with weatherproof backbox, Cat6A patch panel at the IDF, UL-listed power supplies for any 12V/24V camera, labeled and tested before cameras are mounted.

Coastal / Corrosive Environment

NEMA 4X stainless-steel enclosures for outdoor cameras, 316-grade stainless brackets, silicone dielectric grease on every connector, hot-dipped galvanized or powder-coated steel poles. Budget 15-25% more on accessories vs. standard outdoor — and plan for 3-5 year inspection cycles rather than 10.

Box-Camera LPR Application

Box camera with 50-150mm telephoto lens, dedicated 850nm IR illuminator at same height as camera, pole-mount bracket with junction box, UL power supply for camera + illuminator. LPR-specific enclosures with anti-reflective glass to avoid nighttime IR bloom. Typical deployment: dedicated lane camera, not general-purpose surveillance.

Parking Garage Retrofit

Existing analog coax cable replaced via NVT Phybridge or similar PoE-over-coax, vandal-resistant dome enclosures at ground level, low-profile bullet cameras on ceiling, LED-plus-IR-compatible illuminators to handle harsh fluorescent lighting. Enclosures rated for vehicle-exhaust environment.

Frequently Asked Questions

Do I need the OEM bracket for my camera, or will a generic bracket work?

For most commercial installations, specify the OEM bracket. Brand-specific brackets include proper cable routing, gasketed weather seals, and mounting-hole patterns matched to the camera — which matters more than the cost savings of a generic bracket. Generic brackets are acceptable for indoor standard-dome cameras on flat surfaces; for outdoor, vandal-rated, or pendant applications, use OEM.

What NEMA rating do I need for outdoor camera enclosures?

NEMA 4 for most weather-exposed deployments (driving rain, snow). NEMA 4X for coastal, industrial, or food-processing environments (adds corrosion resistance — typically stainless steel or fiberglass construction). NEMA 6 for temporary submersion or flood-prone areas. The IP-rating equivalent is IP66 for NEMA 4, IP66 + corrosion for NEMA 4X, IP67 for NEMA 6.

How do I choose the right lens focal length for a box camera?

Work backward from the scene. Identify the farthest point you need identification-grade coverage, use our DORI guide to calculate required pixels-per-foot at that distance, and match lens focal length + sensor size to deliver that PPF. A 4mm lens on a 1/3" sensor covers ~60° horizontal FOV; a 12mm lens on the same sensor covers ~20°. Wide FOV = shorter identification distance.

What's the difference between 850nm and 940nm IR illuminators?

850nm is more energy-efficient — you get more effective range per watt — but produces a faint visible red glow from the LEDs. 940nm is truly invisible to the human eye but requires about 2x the power for equivalent range, and many cameras have lower sensor sensitivity at 940nm. For deterrent visibility or cost-efficient long-range, 850nm; for covert applications, 940nm.

Can I power an IP camera with a generic 12V wall-wart?

Not for a commercial deployment. Generic wall-warts are unregulated, not UL-listed for security applications, and typically don't include surge protection. Use a UL-listed surveillance power supply (Altronix AL series, UL 294 or UL 603) with battery backup where required. PoE is preferred when possible — single cable, centralized power management, UPS-backed.

What cable jacket rating do I need for in-ceiling runs?

Plenum-rated (CMP) cable is required for any run through a return-air plenum space above suspended ceilings (most commercial buildings). Riser (CMR) for vertical shafts between floors. PVC (CM) for open office spaces only. Using non-plenum cable in a plenum space is a fire-code violation under NFPA 70 and will be rejected by inspectors. Budget plenum cable for any building where you're not 100% sure of the return-air path.

Accessories

Deployment Considerations

Sub categories

Showing Results for Accessories

Ubiquiti UACC-OM-SM-10G-S-2 10 Gbps Single-Mode SFP+ Transceiver

Ubiquiti UACC-OM-SM-10G-S-20 10 Gbps Single-Mode SFP+ Transceiver

Ubiquiti UACC-OM-SM-1G-S-2 Single-Mode Optical Module (2-Pack)

Ubiquiti UACC-OM-SM-1G-S-20 1 Gbps Single-Mode Optical Module

Ubiquiti UACC-PANICBAR Single-Latched Emergency Door Panic Bar

Ubiquiti UACC-POE+++-10G adapter that powers UniFi PoE+++

Ubiquiti UACC-POE++-10G adapter that powers UniFi PoE++ devices

Ubiquiti UACC-POE+-2.5G adapter that powers UniFi PoE+ devices

Ubiquiti UACC-POE+-USBC PoE+ AC Adapter with USB-C Input

Ubiquiti UACC-PRO-AP-AM Wall mount for an U6 Pro or AC Pro

Ubiquiti UACC-PRO-BULLET-ENHANCER-W IR LED & Radar Detection Accessory

Ubiquiti UACC-PRO-MAX-16-RM rack-mount accessory

Ubiquiti UACC-PSU-12V-150W Hot-Swappable Power Module

Ubiquiti UACC-PSU-12V-550W Hot-Swappable Power Module

Ubiquiti UACC-PSU-27V-250W 250W AC/DC Power Supply

Ubiquiti UACC-PSU-UDW 550W Auxiliary Power Supply Module

Browse by Product Family

What to Look For When Buying

Technology Stack

Typical Deployment Scenarios

Top Brands for Outdoor Deployments

Frequently Asked Questions

Related Categories

Engineering Reading