Pelco P2230L-FW0 vs Pelco P2230L-FW1: Specification Comparison
The Pelco P2230L-FW0 and P2230L-FW1 are both 2MP 30x PTZ dome cameras from the Spectra Professional 2 series, sharing the same sensor, zoom range, compression formats, analytics suite, and ONVIF compliance. The sole documented distinction between them is mounting form factor: the FW0 is specified as a flush wall-mount dome, while the FW1 is specified as a standard PTZ dome with an indoor environment rating. This comparison is intended to help installers and IT buyers choose the correct variant for their mounting configuration and deployment environment.
In This Guide
How do the imaging specs compare?
Both the P2230L-FW0 and P2230L-FW1 share identical imaging hardware and performance specifications. Each uses a 1/2.8-inch progressive scan CMOS sensor delivering 1920×1080 (2MP) resolution at up to 60 fps. The 30x optical zoom lens covers a focal length range of 4.3–129 mm, providing a horizontal field of view of 77° at wide angle and 2.6° at full telephoto. Wide dynamic range is rated at 120 dB via Pelco's SureVision processing on both units.
Video compression options are identical across both models: H.265, H.264, and Motion JPEG. Neither model's provided specifications include a minimum illumination figure, IR range, or low-light lux rating, so no comparison on those parameters is possible from the available data. Pan range is 360° continuous on both; tilt range is -90° to +1° on both, with 256 preset positions supported on each.
What about installation and environment?
Both cameras carry IP66 and IP67 ingress protection ratings and an IK10 impact resistance rating, indicating equivalent resistance to dust, water jets, temporary immersion, and mechanical impact. Operating temperature range is identical at -10°C to +60°C. Both are PoE+ powered, eliminating the need for a separate power run.
The key installation difference is form factor. The P2230L-FW0 is specified as a flush wall-mount dome, suited to installations where a low-profile, surface-flush appearance against a vertical surface is required. The P2230L-FW1 is specified as a standard PTZ dome and carries an Indoor environment rating not present in the FW0 spec sheet. Buyers should confirm ceiling versus wall mounting requirements and whether an indoor-only rating is acceptable for their deployment before selecting between these two variants.
Which fits your VMS and analytics better?
ONVIF compliance is identical on both models: Profile S, Profile T, Profile G, and Profile M are all supported, providing broad VMS interoperability for live streaming, recording, event handling, and metadata. The analytics suite is also the same on both: auto-tracker, Electronic Image Stabilization (EIS), and motion detection are listed for each.
Neither model's provided specifications include mention of on-board edge storage, audio input or output, or alarm I/O. No data is available to distinguish the two units on any of these parameters. Buyers requiring local SD card recording or two-way audio should consult Pelco datasheets directly, as those specifications are absent from the provided data for both models.
Which should you choose: the P2230L-FW0 or the P2230L-FW1?
Our take: The P2230L-FW0 is the stronger choice when the installation calls for a flush wall-mount configuration, as that is the sole documented form-factor difference between these two models. Both cameras are otherwise specification-identical: 2MP at 60 fps, 30x optical zoom from 4.3–129 mm, 120 dB SureVision WDR, IP66/IP67/IK10 durability, PoE+ power, and full ONVIF Profile S/T/G/M compliance. The P2230L-FW1 carries an Indoor environment rating not listed for the FW0, which may be relevant for liability or compliance documentation in covered-but-not-outdoor spaces. Neither model lists a minimum illumination figure, edge storage option, or audio capability in the provided specs. Select the FW0 for flush wall-mount deployments; select the FW1 where a standard dome ceiling mount is planned and an explicit indoor rating is required by the project specification.
Side-by-Side Comparison
Spec-for-spec, from manufacturer data.
| Specification | Pelco P2230L-FW0 | Pelco P2230L-FW1 |
|---|---|---|
| Series | Spectra Professional 2 | Spectra Professional 2 |
| Part Number | P2230L-FW0 | P2230L-FW1 |
| Resolution | 2MP (1920×1080) | 2MP (1920×1080) |
| Image Sensor | 1/2.8" progressive scan CMOS | 1/2.8" progressive scan CMOS |
| Max Frame Rate | 60 fps | 60 fps |
| Optical Zoom | 30x | 30x |
| Lens Focal Length | 4.3–129 mm | 4.3–129 mm |
| HFOV | 77° (wide) to 2.6° (tele) | 77° (wide) to 2.6° (tele) |
| WDR | 120 dB SureVision | 120 dB SureVision |
| Video Compression | H.265; H.264; Motion JPEG | H.265; H.264; Motion JPEG |
| Pan / Tilt Range | 360° continuous; -90° to +1° | 360° continuous; -90° to +1° |
| Preset Positions | 256 | 256 |
| Analytics | Auto-tracker; EIS; Motion Detection | Auto-tracker; EIS; Motion Detection |
| ONVIF Compliance | Profile S; T; G; M | Profile S; T; G; M |
| Ingress Protection | IP66 / IP67 | IP66 / IP67 |
| Impact Rating | IK10 | IK10 |
| Operating Temperature | -10°C to +60°C | -10°C to +60°C |
| Power | PoE+ | PoE+ |
| Form Factor | Flush wall-mount dome | PTZ dome |
| Environment Rating | — | Indoor |
| Housing Color | White | White |
| Warranty | 5-year | 5-year |
Frequently Asked Questions
Which should you choose: the P2230L-FW0 or the P2230L-FW1?
The P2230L-FW0 is the stronger choice when the installation calls for a flush wall-mount configuration, as that is the sole documented form-factor difference between these two models. Both cameras are otherwise specification-identical: 2MP at 60 fps, 30x optical zoom from 4.3–129 mm, 120 dB SureVision WDR, IP66/IP67/IK10 durability, PoE+ power, and full ONVIF Profile S/T/G/M compliance. The P2230L-FW1 carries an Indoor environment rating not listed for the FW0, which may be relevant for liability or compliance documentation in covered-but-not-outdoor spaces. Neither model lists a minimum illumination figure, edge storage option, or audio capability in the provided specs. Select the FW0 for flush wall-mount deployments; select the FW1 where a standard dome ceiling mount is planned and an explicit indoor rating is required by the project specification.
Is the P2230L-FW0 or P2230L-FW1 better for low-light performance?
Based on the provided specifications, neither model lists a minimum illumination or lux rating, so a low-light comparison between the two cannot be made from available data. Both share the same 1/2.8-inch CMOS sensor and 120 dB SureVision WDR, indicating identical imaging hardware.
Can the P2230L-FW0 or P2230L-FW1 be used outdoors?
Both models carry IP66 and IP67 ingress protection and IK10 impact ratings, which are consistent with outdoor-capable housings. However, the P2230L-FW1 spec sheet includes an Indoor environment rating, while the P2230L-FW0 does not list an environment rating in the provided data. Installers should verify suitability for their specific outdoor exposure conditions against the full Pelco datasheet.
What is the actual difference between the P2230L-FW0 and P2230L-FW1?
Based solely on the provided specifications, the documented difference is mounting form factor: the P2230L-FW0 is a flush wall-mount dome and the P2230L-FW1 is a standard PTZ dome. The FW1 also lists an Indoor environment rating not present in the FW0 spec. All imaging, optical, compression, analytics, power, durability, and ONVIF specifications are identical between the two.
Get a Second Opinion on Your Camera Choice
Share your site layout, coverage goals, and budget. Our team will validate the camera selection, flag anything we would change, and recommend products that match the use case.