Hanwha QNV-8010R vs i-PRO X25500-V3LN: Specification Comparison
Both the Hanwha QNV-8010R and the i-PRO WV-X25500-V3LN are 5MP fixed-dome IP cameras targeting commercial and light-industrial surveillance installations. They share the same sensor class, resolution tier, IK10 vandal resistance, and IP66 weatherproofing, making them genuine cross-shop candidates. Key differentiators include lens type (fixed vs. motorized varifocal), IR range, WDR ceiling, PoE class, AI analytics depth, audio capability, and warranty length — all covered spec-for-spec below.
In This Guide
How do the imaging specs compare?
Both cameras use an approximately 1/2.8-inch CMOS sensor at 5MP resolution. The QNV-8010R outputs a native 4:3 frame at 2592×1944, while the X25500-V3LN offers both 4:3 (up to 3072×2304) and 16:9 (up to 3072×1728) modes — giving the i-PRO a slight pixel-count edge in raw resolution. On WDR, the gap is substantial: the Hanwha is rated at 120 dB; the i-PRO claims 132 dB with Super Dynamic enabled at level 31. Minimum illumination also favors the i-PRO at 0.02 lux (B&W with IR) versus 0.15 lux color / 0 lux IR (with IR active) for the Hanwha.
Lens configuration is the sharpest divide. The QNV-8010R ships with a fixed 2.8mm lens at F2.0, delivering a 105° horizontal field of view — suitable for wide-angle coverage of a defined zone without repositioning. The X25500-V3LN offers a 3.1× motorized varifocal lens spanning 2.9–9mm (F1.3 wide, F2.5 tele), covering 33–103° horizontal, which allows remote focal-length adjustment after mounting. IR reach also differs markedly: the Hanwha is specified at 20m (65.6 ft); the i-PRO reaches 70m (230 ft). DORI detect range reflects this — 40m (Hanwha, fixed-lens only) versus 48.9m wide / 207.4m tele (i-PRO).
What about installation and environment?
Both cameras are rated IP66 and IK10, confirming dust-tight, water-jet-resistant housings and 50-joule impact resistance. The i-PRO additionally carries IP67, NEMA 4X, and UL/c-UL/CE/IEC62368-1 safety certifications, plus a 40 m/s wind resistance specification; none of these appear in the Hanwha spec sheet. Operating temperature ranges diverge: the QNV-8010R is rated −30°C to +55°C, while the X25500-V3LN extends to −40°C (power-on: −30°C) to +55°C, giving the i-PRO an advantage in extreme-cold deployments.
Power requirements differ by PoE class. The QNV-8010R operates on IEEE 802.3af (PoE Class 3), drawing a maximum of 7.5W — compatible with any standard PoE switch port. The X25500-V3LN requires IEEE 802.3at (PoE+, Class 4) at up to 14.2W, meaning a PoE+ capable switch or injector is mandatory. The Hanwha weighs 510g (1.12 lb) in an ø120.3×91.7mm dome; the i-PRO is heavier at 1.1 kg (2.43 lb) in an ø154×105mm dome. Both mount as standard dome units; the Hanwha lists accessory part numbers (hanging mount SBP-122HMW, backbox SBV-120GW) in its spec sheet; the i-PRO spec sheet does not list accessory part numbers.
Which fits your VMS and analytics better?
Both cameras support ONVIF Profile S, G, and T. The i-PRO additionally lists ONVIF Profile M, which supports metadata streaming for AI-driven analytics events — relevant for VMS platforms that consume structured metadata. Protocol coverage is broadly similar; the i-PRO spec sheet also lists SFTP and MQTT where the Hanwha does not. The Hanwha supports up to 6 unicast users simultaneously; the i-PRO supports up to 14 simultaneous users, a meaningful difference in multi-operator environments.
Analytics depth differs substantially. The QNV-8010R includes motion detection, tampering, defocus detection, virtual area (intrusion/enter/exit), and virtual line (crossing/direction) — all edge-processed. The X25500-V3LN specifies 8 AI Video Analytics detection types and AI Sound Classification covering gunshot, yell, vehicle horn, and glass break. Audio hardware is absent on the Hanwha (no audio input or output listed). The i-PRO provides a 3.5mm stereo mic input and 3.5mm audio output with full-duplex support. On-board storage: the QNV-8010R supports up to 128GB microSD; the X25500-V3LN supports up to 512GB microSDXC. The Hanwha carries a 3-year warranty; the i-PRO carries a 5-year warranty.
Which should you choose: the QNV-8010R or the X25500-V3LN?
Our take: The QNV-8010R is the stronger choice when the installation is cost-constrained, uses a standard PoE (802.3af) switch infrastructure, and the camera position and coverage angle are already fixed. It draws only 7.5W maximum versus the i-PRO's 14.2W, requires no PoE+ upgrade, and its fixed 2.8mm/105° lens simplifies commissioning in confined indoor zones. However, three spec deltas favor the X25500-V3LN for perimeter or outdoor deployments: IR range is 70m versus 20m; dynamic range is 132 dB versus 120 dB; and the motorized 2.9–9mm varifocal lens allows remote zoom adjustment without physical repositioning. Add the i-PRO's AI Sound Classification, ONVIF Profile M metadata streaming, 512GB edge storage capacity, 14-user concurrency, and 5-year warranty, and the X25500-V3LN is the better fit for outdoor perimeter sites, AI-capable VMS platforms, and installations subject to extreme cold below −30°C.
Side-by-Side Comparison
Spec-for-spec, from manufacturer data.
| Specification | Hanwha QNV-8010R | i-PRO X25500-V3LN |
|---|---|---|
| Resolution | 2592×1944 (5MP, 4:3) | 3072×2304 (5MP, 4:3) / 3072×1728 (16:9) |
| Image Sensor | 1/2.8" CMOS | Approx. 1/2.8" CMOS |
| Lens / Focal Length | 2.8mm fixed, F2.0 | 2.9–9mm motorized varifocal, F1.3–F2.5 |
| Optical Zoom | — | 3.1× |
| Horizontal FOV | 105° | 33–103° (zoom-dependent) |
| Min. Illumination | 0.15 lux (color) / 0 lux IR | 0.02 lux (B&W, IR LED) |
| IR Range | 20m (65.6 ft) | 70m (230 ft) |
| Wide Dynamic Range | 120 dB | 132 dB (Super Dynamic level 31) |
| Max Frame Rate | 30fps @ 5MP | 30fps |
| Video Compression | H.265, H.264, MJPEG | H.265, H.264, MJPEG |
| IP Rating | IP66 | IP66, IP67, NEMA 4X |
| Vandal / Impact Rating | IK10 | IK10 (50J, IEC 60068-2-75) |
| Operating Temperature | −30°C to +55°C | −40°C to +55°C (power-on: −30°C) |
| Power Input / PoE Class | IEEE 802.3af, Class 3, max 7.5W | IEEE 802.3at (PoE+), Class 4, max 14.2W |
| Edge Storage | microSD/SDHC/SDXC, up to 128GB | microSDXC, up to 512GB |
| Audio | — | 3.5mm mic in / 3.5mm audio out, full duplex |
| ONVIF Profiles | S, G, T | S, G, T, M |
| AI / Edge Analytics | Motion, tampering, defocus, virtual area/line | 8 AI detection types + AI Sound Classification |
| Simultaneous Users | 6 (unicast) | Up to 14 |
| Dimensions | ø120.3×91.7mm | ø154×105mm |
| Weight | 510g (1.12 lb) | 1.1 kg (2.43 lb) |
| Warranty | 3 years | 5 years |
Frequently Asked Questions
Which should you choose: the QNV-8010R or the X25500-V3LN?
The QNV-8010R is the stronger choice when the installation is cost-constrained, uses a standard PoE (802.3af) switch infrastructure, and the camera position and coverage angle are already fixed. It draws only 7.5W maximum versus the i-PRO's 14.2W, requires no PoE+ upgrade, and its fixed 2.8mm/105° lens simplifies commissioning in confined indoor zones. However, three spec deltas favor the X25500-V3LN for perimeter or outdoor deployments: IR range is 70m versus 20m; dynamic range is 132 dB versus 120 dB; and the motorized 2.9–9mm varifocal lens allows remote zoom adjustment without physical repositioning. Add the i-PRO's AI Sound Classification, ONVIF Profile M metadata streaming, 512GB edge storage capacity, 14-user concurrency, and 5-year warranty, and the X25500-V3LN is the better fit for outdoor perimeter sites, AI-capable VMS platforms, and installations subject to extreme cold below −30°C.
Is the QNV-8010R or X25500-V3LN better for low-light performance?
Based on the provided specs, the X25500-V3LN has the advantage: its minimum illumination is listed at 0.02 lux (B&W with IR) versus 0.15 lux color for the QNV-8010R, and its IR illumination reaches 70m compared to 20m. Its dynamic range ceiling is also higher at 132 dB versus 120 dB. Both cameras switch to IR-assisted night mode automatically via ICR.
Can I power either camera from a standard PoE switch?
The QNV-8010R draws a maximum of 7.5W and is rated for IEEE 802.3af (PoE Class 3), so it works with any standard PoE switch port. The X25500-V3LN requires IEEE 802.3at (PoE+, Class 4) at up to 14.2W — a standard 802.3af port is insufficient, so a PoE+ switch or midspan injector is required for the i-PRO.
Which camera supports audio recording?
Only the i-PRO X25500-V3LN includes audio hardware per the provided specifications: it has a 3.5mm stereo mic input and a 3.5mm audio output with half-duplex and full-duplex modes, plus AI Sound Classification for gunshot, yell, vehicle horn, and glass break. The Hanwha QNV-8010R spec sheet lists no audio input or output.
Get a Second Opinion on Your Camera Choice
Share your site layout, coverage goals, and budget. Our team will validate the camera selection, flag anything we would change, and recommend products that match the use case.