Panduit UTP6AX3.5MOR Cat 6A Patch Cord
The Panduit UTP6AX3.5MOR delivers 10GBASE-T performance in a 3.5-meter unshielded patch cord engineered for datacenter, enterprise network, and structured cabling deployments where alien crosstalk mitigation and rapid MACs drive install efficiency. Built on Panduit's TX6A platform, this orange Cat 6A cord uses 24 AWG solid copper conductors in a 6.4mm U/UTP construction with internal foil tape shielding to meet ANSI/TIA-568.2-D and ISO 11801 Class EA standards across the full 500 MHz bandwidth. RapidID pre-installed barcoding enables one-scan port mapping for as-built documentation, eliminating manual labeling during rack buildouts. The tangle-free modular plug latch prevents snags during cable pulls and provides fast, tool-free release — critical when managing dense 48-port ToR switch deployments or troubleshooting live production links.
Key Features
- Cat 6A performance per ANSI/TIA-568.2-D and ISO 11801 Class EA standards, supporting 10GBASE-T Ethernet up to 100 meters
- 3.5-meter (11.5 ft) orange jacket for color-coded VLAN or zone identification in structured cabling systems
- 24 AWG solid copper conductors in U/UTP construction with internal foil tape to limit alien crosstalk in high-density bundles
- RapidID pre-installed barcode on both plug boots for automated port mapping using Panduit RapidID software
- Tangle-free latch design prevents snags during installation and enables single-hand disconnect for faster MACs
- IEEE 802.3af/at/bt Type 3 and Type 4 PoE++ support up to 100W for high-power IP cameras, WAPs, and DAS head-ends
- 2500-cycle plug rating ensures reliable termination integrity across repeated connect/disconnect cycles
- CM flammability rating for installation in commercial horizontal cable pathways and non-plenum risers
- 0.250-inch (6.4mm) cable diameter balances flexibility for tight bend radius routing with structural rigidity to prevent kinking
- RoHS compliant, UL 1863 listed, and meets ANSI/TIA-1096-A transmission requirements for North American telecom infrastructure
Alien crosstalk — interference between adjacent cables — becomes a limiting factor in Category 6A deployments when routing dozens of patch cords through vertical managers or cable trays. The UTP6AX3.5MOR addresses this with solid foil tape wrapping each twisted pair, creating a barrier that isolates pairs from external EMI without requiring full F/UTP or S/FTP shielded cable. This construction delivers the alien crosstalk performance required for 10GBASE-T certification while maintaining the flexibility and termination simplicity of unshielded cabling — no drain wires, bonding straps, or grounded patch panels needed. The 24 AWG solid conductor gauge provides lower DC resistance than stranded equivalents (5.9 Ω per 100m vs. 7.4 Ω for 26 AWG stranded), improving PoE++ power delivery efficiency and reducing insertion loss at high frequencies — critical when pushing 100W Type 4 PoE to PTZ cameras or 802.11ax access points over 90-meter permanent link runs.
RapidID barcoding shifts port documentation from manual post-install work to an automated scan-and-record workflow: RapidID software reads the barcode on each plug end during installation, auto-populates the connection map in your DCIM or cable management database, and outputs labeled patch panel schedules without physical label printers. This accelerates datacenter refreshes or enterprise expansions where hundreds of patch cords land across multiple racks in a single shift. The tangle-free latch eliminates cable snagging during dense patch cord pulls: the low-profile boot flexes away from obstructions and releases with a straight pull rather than a pinch-and-pull motion. The 2500-cycle plug rating ensures RJ45 contact springs retain compliant insertion force after hundreds of troubleshooting swaps — essential for production networks where patch cords get re-patched monthly during VLAN reconfigurations.
CM flammability rating per UL 1863 qualifies this cord for commercial horizontal pathways, equipment rooms, and non-plenum telecommunications spaces per NEC Article 800. The orange jacket supports visual zone segregation — common uses include DMZ segments, VoIP VLANs, or out-of-band management links — enabling field techs to trace Layer 1 connectivity at a glance. Full compliance with ANSI/TIA-568.2-D Category 6A, ISO 11801 Class EA, and IEEE 802.3bt Type 4 PoE++ ensures integration into enterprise structured cabling, datacenter top-of-rack switching, and IP security surveillance networks without performance compromises, meeting as-built certification requirements enforced by network consultants and facility auditors.
