Panduit UTP6AX3.5MBL Cat 6A 3.5M Patch Cord

Panduit UTP6AX3.5MBL TX6A 10Gig Cat 6A UTP Patch Cord

The Panduit UTP6AX3.5MBL delivers 10GBASE-T performance in a slim, manageable form factor designed for high-density datacenter and enterprise network deployments. This 3.5-meter Cat 6A patch cord addresses three critical install challenges: alien crosstalk interference in bundled cable runs, snag-prone latches that slow MACs operations, and asset-tracking overhead in large port counts. Its 0.250-inch diameter and integrated RapidID barcoding streamline both physical layer deployment and ongoing documentation workflows.

Key Features

• Cat 6A U/UTP construction with solid foil tape shielding limits alien crosstalk for reliable 10 Gb/s transmission to 100 meters
• 24 AWG solid copper conductors in unshielded twisted-pair configuration meet ANSI/TIA-568.2-D and ISO 11801 Class EA specifications
• Tangle-free modular plug latch design prevents snags during cable dressing and enables fast release for moves, adds, and changes
• Pre-installed RapidID barcode integrates with Panduit RapidID software for automated port mapping and asset management
• 0.250-inch (6.4mm) cable diameter reduces bundle cross-section in high-density patch panel and switch port deployments
• Rated for 2500 mating cycles with IEEE 802.3bt Type 3 and Type 4 PoE++ devices delivering up to 90W per port
• CM-rated jacket meets commercial building flammability requirements for horizontal and riser applications

Construction and Performance: The TX6A patch cord uses 24 AWG solid copper conductors in a four-pair unshielded twisted-pair (U/UTP) configuration with solid foil tape shielding applied beneath the outer jacket. This construction limits alien crosstalk—electromagnetic interference between adjacent cables in bundled runs—without the diameter penalty and termination complexity of fully shielded F/UTP or S/FTP cables. The solid conductor design provides superior return loss performance compared to stranded alternatives, critical for maintaining 10GBASE-T signal integrity across the full 100-meter permanent link budget. High-performance modular plugs on both ends meet IEC 60603-7 contact geometry and exceed ANSI/TIA-568.2-D Category 6A insertion loss and return loss limits across the 1–500 MHz operating range. The 0.250-inch outer diameter is 20–30% slimmer than standard Cat 6A patch cords, reducing fill ratio in cable management trays and improving airflow in enclosed pathway systems.

Deployment Workflow and Durability: Each cord ships with a pre-installed RapidID barcode label that integrates with Panduit's RapidID port mapping software—scan the barcode at the patch panel port, scan again at the switch port, and the software auto-populates the connection record in your DCIM or cable management database. This eliminates manual spreadsheet documentation and reduces human error during initial deployment and subsequent MAC operations. The tangle-free latch uses a low-profile boot geometry that prevents the release tab from catching on adjacent cables when pulling cords through high-density bundles; the latch still provides positive retention but releases with a single finger press rather than requiring needle-nose pliers to free snagged tabs. The plug and cable assembly is rated for 2500 insertion cycles, ensuring reliable performance in environments with frequent port reconfigurations. PoE++ compliance (IEEE 802.3bt Type 3 and Type 4) confirms the cable can safely carry up to 90W continuous power alongside data without conductor heating or insulation degradation, critical for IP camera, wireless AP, and LED lighting deployments where remote powering eliminates dedicated electrical drops.

The UTP6AX3.5MBL exceeds ANSI/TIA-568.2-D Category 6A and ISO 11801 Class EA transmission requirements, meets ANSI/TIA-1096-A modular plug performance standards, and carries UL 1863 listing for communication cable assemblies. RoHS compliance confirms lead-free construction for installations subject to hazardous substance regulations. The 3.5-meter length suits top-of-rack to mid-rack server connections, patch panel to adjacent switch uplinks, and cross-connect jumpers in equipment rooms where pre-terminated assemblies reduce field termination labor and ensure factory-tested performance on every link.