Panduit UTP6AX3.5MBU 10Gig Cat 6A Patch Cord 3.5M Blue

Panduit UTP6AX3.5MBU TX6A™ 10Gig Cat 6A UTP Patch Cord

The Panduit UTP6AX3.5MBU delivers certified 10GBASE-T performance in a 3.5-meter (11.5 ft) unshielded twisted pair patch cord engineered for high-density datacenter racks, enterprise network closets, and IP surveillance infrastructures where alien crosstalk rejection and PoE++ power delivery are non-negotiable. Built on 24 AWG solid copper conductors with solid foil tape shielding between pairs, this blue CM-rated cord exceeds ANSI/TIA-568.2-D Category 6A and ISO 11801 Class EA channel requirements while maintaining a slim 0.250-inch (6.4 mm) diameter for superior cable-management density in confined pathways. Factory-terminated with Panduit's high-performance modular plugs and equipped with RapidID pre-installed barcodes, the UTP6AX3.5MBU streamlines MAC operations and asset tracking in environments where uptime and traceability are critical.

Key Features

• TX6A™ 10Gig platform — certified 10 Gb/s transmission over full 100-meter channel per TIA-568.2-D Cat 6A
• Solid foil tape between pairs limits alien crosstalk (AXT) in high-density bundle deployments
• 24 AWG solid copper conductors — lower DC resistance than stranded equivalents for extended PoE reach
• Tangle-free latch design prevents snags during cable pulls and enables fast single-hand release
• RapidID barcode pre-installed — integrates with Panduit RapidID software for automated port mapping and asset management
• 0.250-inch (6.4 mm) overall diameter — 30% slimmer than standard Cat 6A for improved airflow and pathway fill
• IEEE 802.3bt Type 3 and Type 4 compatible — supports PoE++ up to 90W for IP cameras, access points, and VoIP phones
• 2500-cycle plug durability rating — exceeds TIA-1096-A and IEC 60603-7 requirements for high-traffic patch fields

Panduit's TX6A unshielded design solves a persistent challenge in 10GBASE-T deployments: maintaining alien crosstalk margin without the grounding complexity of shielded cabling. The solid foil tape barrier between each twisted pair achieves the same near-end alien crosstalk (ANEXT) and far-end alien crosstalk (AFEXT) performance as F/UTP systems, but eliminates the need for shielded jacks, grounded patch panels, and bonding continuity audits that complicate moves and adds. For integrators managing mixed-vendor environments or retrofitting existing Cat 6 infrastructures to 10Gig speeds, this approach cuts installation labor by 40% compared to fully shielded channel alternatives while preserving full TIA-568.2-D headroom. The 3.5-meter length is purpose-built for rack-to-rack links in 42U cabinets and cross-aisle connections in hot-aisle/cold-aisle datacenter layouts, where excess slack creates airflow obstruction and the 0.250-inch diameter becomes a tangible density advantage. In a typical 1U 48-port switch deployment, you'll fit 35% more UTP6A cords through a 2-inch D-ring compared to legacy 0.330-inch Cat 6A cables, directly improving thermal performance in sealed network closets.

RapidID barcode integration addresses the asset-tracking gap that causes 60% of enterprise MAC ticket delays: Which port connects to which endpoint? The factory-applied barcode on each cord links to Panduit's RapidID software (sold separately), enabling technicians to scan both ends of a cord during installation and auto-populate a live port map in your DCIM or CMMS platform. When a PoE camera goes offline at 2 AM, your NOC team identifies the physical patch-panel port in under 10 seconds instead of tracing cables by hand with a toner. The tangle-free latch compounds this advantage by surviving the 2500-cycle durability test without cracked tabs or retention failures — a measurable improvement over generic molded-boot designs that fail at 800-1200 cycles in high-churn environments like university dorm IDF closets or retail back-of-house network stacks. For IP surveillance integrators, the IEEE 802.3bt Type 3/4 compatibility is the differentiator: this cord supports the full 90W PoE++ power budget required by next-generation PTZ cameras with onboard AI analytics, IR illuminators, and active cooling, eliminating the mid-span injector and its associated failure point.

Every UTP6AX3.5MBU ships with test results verifying compliance to ANSI/TIA-568.2-D insertion loss, return loss, NEXT, PSNEXT, ACR-F, and PSACR-F parameters across the full 1-500 MHz bandwidth, and carries UL 1863 listing for use in plenum-equivalent air-handling spaces when installed in compliant pathways. The CM flammability rating suits general-purpose horizontal and riser applications; for plenum ceiling grids, specify Panduit's CMP-rated TX6A variant. RoHS compliance ensures compatibility with EU and California e-waste regulations for government and healthcare deployments. This is the patch cord you spec when the network architect demands TIA certification, the facilities team needs asset-tracking integration, and the budget requires a single SKU that works across surveillance, unified communications, and datacenter edge without compromise.