Mounting Brackets & Kits for IP Cameras

Plan Your Deployment

Wall, ceiling, pole, or corner mounting requirements
Indoor vs outdoor environmental exposure
Device model compatibility and load capacity
Vandal resistance and tamper considerations
Future service access and cable routing planning

Sub categories

Showing Results for Mounting Brackets & Kits

Compare

Add to Cart The item has been added
i-PRO

SKU: WV-QSR503F1-W

i-PRO WV-QSR503F1-W Wall Mount Bracket 1.5 NPS

Wall mount bracket with 1.5" NPS thread for i-PRO dome cameras
- 1.5" National Pipe Standard threaded connection ensures secure fit across compatible i-PRO camera lines
- White powder-coat finish blends into indoor ceilings and walls without drawing attention
- Lightweight at 11.02 lbs for single-technician installation and positioning
In stock · Usually Ships Same Business Day

$63.64 $56.99 Save $6.65

Add to Cart
The item has been added
Compare

Out of stock
i-PRO

SKU: WV-QSR503M-W

i-PRO WV-QSR503M-W Wall Mount Bracket ISO Male

Wall mount bracket for dome cameras with 1.5" ISO male thread
- 1.5" ISO male threaded connection fits standard dome cameras
- White finish wall-mount design for indoor and outdoor installations
- Supports standard dome camera weight loads up to 11.02 lbs
Special Order · Usually Ships in 2-3 Weeks

$72.20 $64.99 Save $7.21

Add to Cart
The item has been added
Compare

Out of stock
i-PRO

SKU: WV-QSR503M1-W RB

i-PRO WV-QSR503M1-W RB Shroud Bracket

Protective shroud bracket with ANSI thread for i-PRO cameras
Special Order · Usually Ships in 2-3 Weeks

$85.30 $76.99 Save $8.31

Add to Cart
The item has been added
Compare

Out of stock
i-PRO

SKU: WV-QSR503M1-W

i-PRO WV-QSR503M1-W Wall Mount Bracket 1.5 NPT

Wall mount bracket for dome cameras with 1.5" NPT connection
- 1.5" NPT male thread connects directly to standard poles and conduit
- White finish for discrete mounting on exterior walls and structures
- Rated for 11.02 lbs capacity to secure dome camera installations
Special Order · Usually Ships in 2-3 Weeks

$85.30 $76.99 Save $8.31

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
i-PRO

SKU: WV-QSR504-B

i-PRO WV-QSR504-B Wall Mount Bracket Black

4-screw wall bracket for i-PRO PTZ cameras with salt-spray resistance
- Four-point mounting distributes load evenly, stays secure in high-vibration sites
- Powder-coated steel resists rust, salt spray, and UV degradation for 5–10 years
- Matte black finish blends into walls and ceilings for discrete installations
In stock · Usually Ships Same Business Day

$85.30 $76.99 Save $8.31

Add to Cart
The item has been added
Compare

Out of stock
i-PRO

SKU: WV-QSR504-W

i-PRO WV-QSR504-W Wall Mount Bracket White

Wall mount bracket for i-PRO PTZ cameras, 4-screw white finish
- 4-screw mounting configuration for secure fixed wall installation
- White finish designed for indoor surveillance environments
- Compatible with i-PRO PTZ camera models
Special Order · Usually Ships in 2-3 Weeks

$63.65 $56.99 Save $6.66

Add to Cart
The item has been added
Compare

Out of stock
i-PRO

SKU: WV-QSR504M-W

i-PRO WV-QSR504M-W ISO Male Wall Mount Bracket

Wall mount bracket with ISO male connection for i-PRO PTZ cameras
- ISO male interface supports broad range of i-PRO PTZ and fixed cameras
- 1.5" radius design optimized for secure PTZ camera mounting
- White powder-coat finish resists weathering in indoor and outdoor use
Special Order · Usually Ships in 2-3 Weeks

$85.30 $76.99 Save $8.31

Add to Cart
The item has been added
Compare

Out of stock
i-PRO

SKU: WV-QSR504M1-W

i-PRO WV-QSR504M1-W Wall Mount Bracket 1.5 NPT

Wall mount bracket for i-PRO PTZ cameras with 1.5" NPT connection
- 1.5" NPT male thread matches standard conduit and pole-mount applications
- White powder-coat finish resists corrosion in indoor and outdoor deployments
- Compatible with i-PRO PTZ camera systems and ANSI-threaded equipment
Special Order · Usually Ships in 2-3 Weeks

$85.30 $76.99 Save $8.31

Add to Cart
The item has been added
Compare

Out of stock
i-PRO

SKU: WV-QSR504S-W

i-PRO WV-QSR504S-W Wall Mount Bracket White

White wall mount bracket for i-PRO PTZ cameras in indoor setups
- 4-screw configuration ensures secure, balanced mounting for motorized PTZ units
- Powder-coated white steel finish integrates cleanly with modern facility aesthetics
- Compact wall-mount design optimized for indoor surveillance installations
Special Order · Usually Ships in 2-3 Weeks

$149.25 $133.99 Save $15.26

Add to Cart
The item has been added
Compare

Out of stock
i-PRO

SKU: WV-QSR506F-W

i-PRO WV-QSR506F-W Mount Bracket White

White mount bracket for wall and ceiling i-PRO camera installation
- Dual mounting capability supports both wall and ceiling configurations
- White finish blends discreetly in retail, office, and industrial spaces
- Durable professional-grade construction rated for outdoor environments
Special Order · Usually Ships in 2-3 Weeks

$85.30 $76.99 Save $8.31

Add to Cart
The item has been added
Compare

Out of stock
i-PRO

SKU: WV-QSR506M-W

i-PRO WV-QSR506M-W Mount Bracket

Fixed wall/rack bracket for i-PRO surveillance cameras
- Dedicated mount for i-PRO camera models with permanent positioning
- White finish bracket designed for wall or rack installation
- Mechanical support accessory for standard surveillance deployments
Special Order · Usually Ships in 2-3 Weeks

$85.30 $76.99 Save $8.31

Add to Cart
The item has been added
Compare

Out of stock
i-PRO

SKU: WV-QSR507-B

i-PRO WV-QSR507-B Wall Mount Bracket Black

Wall mount bracket for i-PRO network cameras, 4-screw design
- 4-screw configuration ensures stable, vibration-free mounting on interior walls
- Matte black finish blends discretely into office and retail environments
- Compatible with i-PRO cameras using standard bracket interface for easy swaps
Special Order · Usually Ships in 2-3 Weeks

$127.94 $114.99 Save $12.95

Add to Cart
The item has been added
Compare

Out of stock
i-PRO

SKU: WV-QSR507F-B

i-PRO WV-QSR507F-B ISO Female Black Wall Mount Bracket

ISO female wall bracket for i-PRO cameras with black powder-coat finish
- 1.5" Rp ISO female connection for standardized mounting compatibility
- Black powder-coated corrosion-resistant construction rated for outdoor use
- Wall-mount design supports i-PRO imaging devices and compatible equipment
Special Order · Usually Ships in 2-3 Weeks

$127.94 $114.99 Save $12.95

Add to Cart
The item has been added
Compare

Out of stock
i-PRO

SKU: WV-QSR507F1-B

i-PRO WV-QSR507F1-B ANSI Female Mount Bracket

ANSI female mount bracket with 1.5" NPS threading for wall/ceiling
- Steel construction with black powder-coat finish resists corrosion and UV
- 1.5" NPS female threading connects to standard pipe fittings and i-PRO cameras
- Mounts on walls or ceilings for flexible surveillance system deployment
Special Order · Usually Ships in 2-3 Weeks

$127.94 $114.99 Save $12.95

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
i-PRO

SKU: WV-QSR507F1-W RB

i-PRO WV-QSR507F1-W RB Shroud Bracket

Shroud bracket for i-PRO dual-sensor cameras with ANSI thread mount
In stock · Usually Ships Same Business Day

$114.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
i-PRO

SKU: WV-QSR507F1-W

i-PRO WV-QSR507F1-W Wall Mount Bracket 1.5 NPS

Wall mount bracket with 1.5" NPS thread for i-PRO cameras
- 1.5" NPS female thread connection matches i-PRO camera housings
- White powder-coat finish rated for outdoor structural exposure
- ANSI-compliant construction for fixed wall or architectural mounting
In stock · Usually Ships Same Business Day

$127.94 $114.99 Save $12.95

Add to Cart
The item has been added

What to Look For When Buying

The decisions that matter most before you spec.

Load Rating & Vibration Damping

Mounting brackets must support camera weight (typically 0.5–15 lbs for IP cameras) plus wind load in outdoor deployments. Improperly secured cameras cause system failure during critical incidents; select brackets rated for your camera model and environmental stress factors. Gyro mounts and rubber isolators reduce vibration in high-wind or traffic-adjacent zones.

Cable Routing & PoE Management

Mounting kits with integrated cable glands and strain relief prevent cable pinch points and maintain PoE power delivery stability. Conduit clips and backing plates organize cables at the source, reducing troubleshooting time and protecting against accidental disconnection during maintenance.

Material & Corrosion Resistance

Outdoor and coastal installations require stainless steel or powder-coated aluminum brackets to prevent rust and material degradation. Salt spray, humidity, and UV exposure degrade standard steel within 6–12 months; specify 300/316 stainless for marine environments and 6063 aluminum for standard outdoor use.

Installation Standard & Brand Compatibility

Major brands like Axis, Hanwha, and Vivotek design proprietary mounting interfaces alongside VESA and ISO standard mounts. Verify bracket compatibility with your camera model before procurement; cross-brand mounts may misalign optical paths or create cable stress points.

Height, Angle & Optical Alignment

Camera mounting height and tilt affect pixel density and DORI (Detection, Observation, Recognition, Identification) distances. Adjustable brackets allow field-level fine-tuning; fixed mounts require accurate site survey and pre-deployment calculations to avoid costly repositioning after installation.

Conduit Seal & Weatherproofing

Water ingress at cable entry points causes short circuits and sensor corrosion in wet environments. Select kits with silicone gaskets, stainless steel cable glands, and IP67-rated enclosures; test seals during initial deployment to prevent mid-season failures.

Technology Stack

The specs and acronyms that actually affect mounting brackets & kits performance.

VESA Mount Standards (75/100/200 mm)

Standardized hole patterns used by consumer electronics and some IP camera models. Allows universal bracket compatibility across manufacturers, but always verify camera's screw pitch and load rating before mixing brands.

Wind Load Rating (lbs @ mph)

Manufacturers specify maximum wind speed brackets withstand without camera slip or structural flex. Outdoor installations require ratings matching local weather extremes; most outdoor brackets support 60–120 mph sustained winds, but rooftop or exposed mounting may demand 150+ mph ratings.

Stainless Steel Grades (304/316)

Grade 304 resists general corrosion in most climates; Grade 316 adds molybdenum for superior salt-spray tolerance in coastal zones. Galvanized steel (zinc coating) offers cost savings but degrades 3–5 years faster than stainless in humid/marine environments.

Cable Gland Certifications (IP67/IP68)

IP rating indicates water and dust ingress protection at cable entry. IP67 withstands temporary immersion; IP68 is rated for continuous submersion. Select IP67 minimum for outdoor camera mounts, IP68 for wet-room intercoms and dock-area access readers.

Gyro Mounts & Vibration Damping

Rubber or elastomer isolators reduce micro-vibrations transmitted from poles or wind, stabilizing video in high-motion environments. Critical for PTZ cameras on rooftop poles or traffic-adjacent installations; adds 0.5–2 lbs to mounting weight.

Conduit Diameter & Strain Relief

Brackets specify maximum conduit size (typically 0.5–1.5 inches) and cable bend radius. Exceeding bend-radius limits degrades PoE conductor insulation; use clips and backing plates to maintain manufacturer-specified minimum bend radius (usually 4–6 inches for Ethernet).

Typical Deployment Scenarios

Multi-Story Office Lobby (15 cameras, mixed mount types)

Combine ceiling-mount brackets for overview domes at entry points, corner brackets for stairwell coverage, and recessed in-wall mounts for elevator vestibules. Use Hanwha or Axis unified bracket kits to simplify procurement; junction-box assemblies pre-mount cable glands and backing plates, reducing on-site assembly by 40%.

Outdoor Parking Lot Perimeter (24 cameras, 30-ft poles)

Specify heavy-duty pole mounts rated for 80+ mph wind load, stainless steel hardware, and gyro isolation for vibration damping. Include pendant conduit kits with silicone gaskets and IP67 glands; plan cable routing inside pole conduit to protect PoE runs from weather and UV degradation.

Hospital Intercom & Card-Reader Network (40 stations, recessed mount)

Use recessed trim-ring kits designed for flush in-wall mounting at staff stations, nurse calls, and secure doors. Select 316 stainless trim rings; pair with concealed junction boxes to route cables through wall cavities, maintaining clean aesthetics while protecting core network connections from physical damage.

Warehouse Dock & Data-Capture Zone (8 cameras, industrial-grade PTZ)

Heavy-duty PTZ mounts on gantry beams require gyro dampers and reinforced backing plates rated for 20+ lbs static load. Route PoE and pan-tilt control cables through conduit; ensure sufficient power budget per PoE planning guidance for simultaneous motor operation across all units.

Frequently Asked Questions

What's the difference between VESA and proprietary camera mounts?

VESA (75/100/200 mm) are universal screw-hole patterns used by monitors and some IP cameras, allowing mixed-brand bracket compatibility. Proprietary mounts are manufacturer-specific and often integrate cable routing and power connectors for a given camera family. Always verify your camera's mounting interface before ordering; mixing standards can misalign the lens or create cable stress.

How do I choose between wall, pole, and ceiling mounting?

Wall mounts suit indoor hallways and perimeter coverage; ceiling mounts provide overhead overview angles; pole mounts enable tall outdoor installations for parking lots and large perimeters. Consider viewing angle (DORI distance), cable routing (PoE run length), and environmental exposure (rain, wind, UV). Outdoor deployments typically require pole or soffit brackets with stainless hardware and weatherproof conduit seals.

What wind-load rating do I need for rooftop or pole-mounted cameras?

Most outdoor brackets are rated 60–80 mph; rooftop and tall-pole installations in high-wind zones (hurricane, mountain, or exposed coastal areas) require 100–150+ mph ratings. Consult local building codes and weather records for your site. Undersized brackets allow camera drift, misaligning views and degrading identification accuracy over distance.

Why should I use stainless steel brackets in coastal or humid climates?

Standard steel and galvanized coatings corrode within 2–5 years in salt-spray or high-humidity zones, causing bracket failure and camera drop hazards. Stainless 304 resists general corrosion; 316-grade adds molybdenum for superior marine tolerance. The upfront cost (typically 20–40% more) prevents emergency replacement and liability exposure.

What's an IP67 cable gland, and why does it matter for outdoor mounts?

IP67 means the gland prevents dust and temporary water submersion at cable entry points. Water ingress corrodes connectors and shorts PoE circuits, causing mid-deployment failures. Pair IP67 glands with silicone gaskets and stainless fasteners; test seals before final installation to confirm weatherproofing.

Can I use the same mounting bracket for different camera brands?

Only if both cameras share VESA or ISO mounting standards. Proprietary mounts (common in Axis, Vivotek, and Hanwha models) are not interchangeable. Mixing brands often requires adapter plates, which add bulk, cost, and potential optical misalignment. Standardize on one or two manufacturer families per project to simplify spare-parts inventory and on-site troubleshooting.

Mounting Brackets & Kits

Plan Your Deployment

Sub categories

Showing Results for Mounting Brackets & Kits

i-PRO WV-QSR503F1-W Wall Mount Bracket 1.5 NPS

i-PRO WV-QSR503M-W Wall Mount Bracket ISO Male

i-PRO WV-QSR503M1-W RB Shroud Bracket

i-PRO WV-QSR503M1-W Wall Mount Bracket 1.5 NPT

i-PRO WV-QSR504-B Wall Mount Bracket Black

i-PRO WV-QSR504-W Wall Mount Bracket White

i-PRO WV-QSR504M-W ISO Male Wall Mount Bracket

i-PRO WV-QSR504M1-W Wall Mount Bracket 1.5 NPT

i-PRO WV-QSR504S-W Wall Mount Bracket White

i-PRO WV-QSR506F-W Mount Bracket White

i-PRO WV-QSR506M-W Mount Bracket

i-PRO WV-QSR507-B Wall Mount Bracket Black

i-PRO WV-QSR507F-B ISO Female Black Wall Mount Bracket

i-PRO WV-QSR507F1-B ANSI Female Mount Bracket

i-PRO WV-QSR507F1-W RB Shroud Bracket

i-PRO WV-QSR507F1-W Wall Mount Bracket 1.5 NPS

Browse by Product Family

What to Look For When Buying

Technology Stack

Typical Deployment Scenarios

Top Brands for Mounting Brackets & Kits

Frequently Asked Questions

Related Categories

Engineering Reading