Altronix NETWAYXTG 1G Ethernet Repeater with PoE/PoE+
Overview
The Altronix NETWAYXTG is a 1 Gigabit Ethernet repeater with integrated PoE/PoE+ output, purpose-built for surveillance and security installations where a single cable run from a PoE switch can't reach the endpoint device. Powered by a local 24VAC or 24VDC supply, the NETWAYXTG regenerates the data signal and injects fresh PoE power — up to 30W on the 802.3at standard — so you can extend network reach beyond the 100-meter Ethernet limit without sacrificing speed or power budget. At just 3.8" x 2.5" x 1" and 0.2 lb., it mounts inside a backbox, junction enclosure, or alongside a camera bracket without adding meaningful bulk to the installation.
Browse the full Altronix power and networking catalog to see the broader ecosystem this device fits into, including power supplies, surge protectors, and access control power hardware.
Key Features
- 1Gbps Auto-Crossover RJ45 Port: Full 10/100/1000Mbps auto-negotiation means you're not bottlenecked on the downstream device side — whether you're feeding a 100Mbps IP camera or a 1G edge switch, the NETWAYXTG matches the link speed automatically. The auto-crossover function eliminates the need for a crossover cable or adapter in the field.
- IEEE 802.3at (30W) and 802.3af (15.4W) PoE Output: The 30W 802.3at output covers virtually every PTZ camera, multi-sensor camera, and access control reader on the market. If your endpoint only needs 802.3af, the NETWAYXTG steps down to 15.4W automatically. This range of PoE power delivery means you're not buying a different repeater for different endpoint classes.
- 24VAC or 24VDC Input at 1.5A: Most Altronix power supplies and many third-party security power distributions output 24VAC — so you can tap an existing supply in the enclosure rather than running a new AC circuit. The 1.5A input draw is low enough to share a multi-output supply with other devices on the same zone.
- CAT5e or Better, 4-Pair Wiring: The NETWAYXTG uses all four pairs of CAT5e (or CAT6) cable, which is consistent with Gigabit Ethernet wiring standards. If your building is pre-wired with CAT5e, you're ready — no re-pull required for 1G operation as long as the cable run is within spec.
- 0°C to 60°C Operating Range: The NETWAYXTG operates from 32°F to 140°F, covering unheated mechanical rooms, above-ceiling spaces, and outdoor-adjacent enclosures in moderate climates. It's not rated for harsh outdoor exposure, so plan enclosure placement accordingly in cold environments below freezing.
- CE European Conformity Listed: CE marking confirms the NETWAYXTG meets EU electromagnetic compatibility and safety directives — relevant for deployments in European facilities or projects with international compliance requirements.
- Compact Form Factor (3.8" x 2.5" x 1"): The sub-1-inch depth means it fits inside a standard single-gang backbox or a compact surface enclosure at the camera location. No dedicated equipment rack or large enclosure needed at the extension point — a meaningful installation cost factor when you're repeating across 10 or 20 camera locations.
Integration & Compatibility
The NETWAYXTG sits between your network switch and the endpoint device — it is protocol-transparent, so it works with any ONVIF, proprietary, or VMS-managed IP camera, access control panel, or wireless access point that accepts standard 802.3af/at PoE. The upstream connection runs from your switch (or another NETWAYXTG for a second hop) over CAT5e or CAT6, while the downstream RJ45 feeds directly into the endpoint. Because it operates at Layer 1, there is no configuration interface, no IP address to manage, and no firmware to update — it installs and is invisible to your network management platform.
Pair the NETWAYXTG with Altronix's own power distribution hardware for a clean single-vendor infrastructure layer. For projects requiring structured documentation, the CE listing supports compliance packages for EU-destined installations. When sizing the upstream PoE switch port, account for the NETWAYXTG's 1.5A draw at 24V plus the endpoint's PoE budget — the repeater draws local power for its own operation, so the upstream switch port only needs to supply data, not PoE power to the repeater itself.
For projects involving high-density IP camera installations, review the camera infrastructure planning guide to align cable runs, enclosure locations, and power zoning before finalizing the repeater placement strategy.
Frequently Asked Questions
Q: Does the NETWAYXTG require PoE power from the upstream switch?
A: No. The NETWAYXTG is powered locally by a 24VAC or 24VDC supply at 1.5A. The upstream switch connection carries data only — no PoE input is required or used from the switch side. This is what allows it to function as a true repeater: it regenerates signal and injects fresh power independently of the upstream switch's PoE budget.
Q: What is the maximum PoE wattage the NETWAYXTG can deliver to a connected device?
A: The NETWAYXTG delivers up to 30W per the IEEE 802.3at (PoE+) standard, and also supports 802.3af at 15.4W. Output class is negotiated automatically with the endpoint device.
Q: What cable type does the NETWAYXTG require?
A: It requires 4-pair CAT5e cable or better (CAT6, CAT6A are compatible). All four pairs must be connected, which is standard for Gigabit Ethernet wiring.
Q: What are the operating temperature limits for the NETWAYXTG?
A: The operating temperature range is 0°C to 60°C (32°F to 140°F). It is not designed for outdoor exposure or sub-freezing environments without additional enclosure heating.
Q: Can the NETWAYXTG be used to extend reach beyond 100 meters from the switch?
A: Yes. That is its primary use case. It regenerates the Ethernet signal at the intermediate point, effectively resetting the 100-meter distance limit so the next cable segment can run another full 100 meters to the endpoint.
Q: Is the NETWAYXTG compatible with any IP camera brand?
A: Yes — it is protocol-transparent and works with any 802.3af/at PoE-compatible endpoint regardless of brand, including cameras from Axis, Hanwha, Hikvision, Vivotek, and others. It operates at Layer 1 and has no impact on the data stream.
I've deployed the NETWAYXTG in a number of warehouse and multi-building campus projects where the switch room is more than 100 meters from the camera location and pulling a second cable back to the IDF isn't in the budget. The 24VAC input is the key detail here — most installers already have a local Altronix power supply or equivalent in the junction enclosure, so you're tapping an existing 24V zone rather than adding a new power circuit. The NETWAYXTG handles the signal regeneration and delivers up to 30W 802.3at PoE to the endpoint, which covers PTZ cameras and dual-head analytics cameras without any derating concern.
Technical Highlights:
- Local 24VAC/VDC Power Input: Drawing 1.5A at 24V, the NETWAYXTG is well within the output capacity of a standard 4-output Altronix supply — you can chain multiple units on a single power zone without a dedicated circuit at each extension point.
- 802.3at 30W PoE Output: The full PoE+ budget at the downstream port means you're not forced to choose a lower-power camera or reader to stay within a constrained PoE budget — 30W covers nearly every mainstream surveillance endpoint on the market today.
- 1Gbps Throughput with Auto-Crossover: The 1G link ensures you're not bottlenecking high-bitrate streams, especially relevant when feeding multi-sensor or 4K cameras where H.265 streams can still push 8–12 Mbps per channel under motion.
Deployment Considerations:
- The NETWAYXTG's 3.8" x 2.5" x 1" footprint fits inside a standard single-gang backbox at the intermediate point — plan junction box placement during rough-in, not after walls are closed.
- Operating temperature ceiling is 60°C (140°F): above-ceiling spaces in direct sun or near HVAC heat exchangers can exceed this in summer — verify ambient temperature at the intended mounting location before committing to placement.
For a large warehouse or distribution center where cameras are concentrated at dock doors and aisle ends — both well beyond 100 meters from the server room — the NETWAYXTG is the cleanest way to extend the run without a secondary IDF. Tap the existing 24V power zone at each intermediate point, and your switch infrastructure stays centralized.
