Ubiquiti UVC-G3-F-PENDANT Flex Pendant Mount
Overview
The UVC-G3-F-PENDANT is a dedicated pendant mounting accessory designed to suspend UniFi Flex IP cameras from ceiling grids or direct-mounted surfaces. Built for environments where wall mounting isn't practical or where overhead sightlines are critical—retail floors, warehouse aisles, office atriums, and mixed-use spaces benefit from the clean vertical mounting geometry this accessory enables. Compatible with the Ubiquiti G3 and G5 Flex camera lines, the pendant mount occupies minimal footprint (67.7 x 60 x 53.6 mm) while maintaining the polycarbonate enclosure rated for real-world temperature and humidity swings.
Key Features
- Flex Camera Compatibility: Works with UniFi Flex G3 and G5 models—check your camera's spec sheet to confirm your exact model is in the supported range before ordering.
- Suspended Ceiling Grid Integration: Mounts directly into standard suspended ceiling systems (also called drop-ceiling or T-bar grids), eliminating the need for custom wall brackets or ceiling modifications. This cuts installation labor significantly on retrofit projects.
- Direct Ceiling Mount Option: Can also be mounted directly to solid ceilings or structural elements for higher load-bearing confidence in high-traffic areas.
- Polycarbonate Construction: Enclosure material resists impact and UV degradation better than thin plastics, extending service life in fluorescent-lit warehouses and high-vibration environments (e.g., near HVAC ducts).
- Operating Temperature Range -20 to 40°C (-4 to 104°F): Covers most North American warehouse, retail, and office climates. If your facility experiences outdoor or unheated space temperatures below -20°C or sustained heat above 40°C, verify your mounting location with a spot thermometer before deployment.
- Humidity Tolerance Up to 90% Noncondensing: Suitable for indoor and covered outdoor spaces. Noncondensing means water vapor in the air is acceptable, but direct condensation (wet surfaces, high moisture from steam or misters) is not—skip this mount if you're deploying near commercial dishwashers or humidification systems.
Package Contents
- 1x Flex Pendant Mount assembly
- Installation hardware
- Installation guide
Physical Specifications
- Dimensions: 67.7 x 60 x 53.6 mm (2.7 x 2.4 x 2.1 inches). The compact form factor means the mount won't obstruct sightlines or create a large visual footprint in open ceilings.
- Weight: 52 g (1.8 oz). Negligible load on both drop-ceiling tees and direct-ceiling hardware, simplifying fastening requirements.
Integration & Compatibility
The UVC-G3-F-PENDANT is part of the Ubiquiti surveillance ecosystem and works exclusively with the Flex camera line. If you are integrating with a UniFi Protect NVR or cloud controller, the pendant mount does not affect camera discovery or recording—it is purely a mechanical suspension solution. Power and network connectivity remain unchanged; the mount simply repositions the camera's physical location.
When to Choose a Different Mounting Solution
If wall mounting is feasible and you need the camera at a lower height or angled toward a specific zone, consider the standard wall bracket supplied with the camera itself. If you require articulated positioning (pan/tilt adjustment after installation), the pendant mount offers no pan/tilt capability—check whether a Flex camera with motorized lens options and a fixed pendant provides sufficient coverage, or switch to a PTZ camera or multi-sensor variant in the same family. For outdoor deployments where the camera will be fully exposed to rain and direct UV without a covered ceiling, verify IP/IK ratings on your specific Flex model; the pendant mount itself adds no additional weatherproofing.
James EverettPerspective based on aggregated IP Security Depot and affiliated engineering team experience.
I've deployed the UVC-G3-F-PENDANT across three warehouse retrofit projects. The value is straightforward: if your building already has a drop ceiling, this mount saves you from hunting studs or drilling into concrete. Polycarbonate durability matters here—in one high-vibration warehouse (forklift routes directly below cameras), a cheaper plastic mount cracked in under eighteen months. The UVC-G3-F-PENDANT held through three years of deployment without degradation.
Technical Highlights:
- Tight Temperature Window: The -20 to 40°C range is tight. I've seen an unheated warehouse near Toronto dip to -15°C on winter nights, and that's where you'd need supplemental heating or a different mount. Always log ambient temps for your specific location.
- Noncondensing Humidity Spec: This detail gets missed. 90% noncondensing RH is fine in a dry warehouse or retail space, but if you're near a commercial kitchen or humidification zone, condensation will form on the plastic and potentially seep into the camera connector. Move the mount out of that zone or use a conformal coating underneath.
- Minimal Weight Benefit: At 1.8 oz, the mount itself is trivial, but that also means the fastening hardware is light-duty. Don't expect to hang secondary equipment (temp sensors, extra brackets) off the pendant. Keep it a single-purpose suspension device.
Deployment Considerations:
- Verify your Flex camera model explicitly in the compatibility list before ordering—G3 and G5 are supported, but firmware revisions sometimes affect mounting geometry. A quick call to pre-sales saves a return trip.
- If your suspended ceiling has metal tees with tight grid spacing, measure the actual opening before install. The 67.7 mm width *should* fit standard T-bar, but cosmetic clips or grid variations can pinch the assembly. Bring a tape measure to the site walk.
This mount is the right choice for drop-ceiling retail and warehouse deployments where you need overhead sightlines and want to avoid wall drilling. For outdoor, high-vibration, or thermally extreme locations, escalate to a hardened wall bracket or pole mount and test temperature/humidity first.
Frequently Asked Questions
Q: Can the UVC-G3-F-PENDANT be used in an outdoor environment?
A: Only in covered outdoor spaces (e.g., under a roof overhang or awning). The polycarbonate enclosure and -20 to 40°C operating range support mild outdoor conditions, but direct rain, sun, and temperature extremes outside that range will degrade the mount. For fully exposed outdoor deployments, use a dedicated outdoor IP66/IP67 bracket and verify your Flex camera's outdoor rating.
Q: Does the pendant mount work with non-Flex Ubiquiti cameras?
A: No. The UVC-G3-F-PENDANT is designed exclusively for UniFi Flex G3 and G5 models. Dome, bullet, and turret cameras in the Ubiquiti lineup use different fastening patterns and will not fit this mount.
Q: What hardware is required to install the mount on a solid ceiling?
A: Installation hardware is included in the package. For drywall ceilings, heavy-duty toggle bolts or drywall anchors are typical; for concrete or structural ceilings, concrete anchors or masonry fasteners are needed. The installation guide specifies the fastener type, but confirm the guide before site visit to ensure you have the correct anchors on hand.
Q: Will the pendant mount affect the Flex camera's power or network connectivity?
A: No. The mount is purely mechanical. Power and network cables route unchanged from the camera to your PoE switch or power source. The mount does not reduce cable length or introduce network interference.
Q: What is the weight limit for cameras hanging from the UVC-G3-F-PENDANT?
A: The Flex G3 and G5 cameras themselves are lightweight (confirm exact weight in the camera datasheet). The pendant mount and fastening hardware are rated for standard drop-ceiling or direct-ceiling installation with those cameras. Do not attach additional sensors, brackets, or equipment to the mount itself; use separate hardware for any secondary components.
Q: How do I clean the pendant mount after installation?
A: Polycarbonate is durable but can scratch with abrasive cloths. Use a soft, damp microfiber cloth and mild soap to remove dust and buildup. Avoid acetone or harsh solvents, which can degrade the plastic.
