Altronix NETWAY1DWPM Outdoor Single-Port Hi-PoE Midspan Injector
Overview
The Altronix NETWAY1DWPM is a single-port outdoor midspan injector purpose-built for powering IP cameras, PTZ heads, WiMAX modems, and WLAN access points in locations where a PoE-capable switch is not nearby or practical. It accepts 115VAC or 230VAC input and delivers up to 60W on a single Ethernet port — enough headroom for high-wattage PTZ cameras and IR illuminators that would saturate a standard 802.3af port. The NEMA 4/4X, IP66-11-rated enclosure handles outdoor installation with no additional housing required, and the -30°C to 70°C operating range (at 30W mode) covers rooftop and parking structure deployments in northern climates without derating.
This unit is listed under the Altronix PoE power solutions line and is engineered specifically for the physical security channel. UL, cUL, CE, TAA, NDAA, and BAA compliance is verified for this SKU — a requirement on federal, state, and education projects where supply-chain certification is audited at the component level.
Key Features
- 60W Maximum PoE Output: Delivers up to 60W on a single port using all four cable pairs, satisfying IEEE 802.3at (30W) and IEEE 802.3af (15W) simultaneously. That ceiling matters when driving a high-wattage PTZ with integrated IR — a 30W PoE+ port leaves no margin, but 60W gives you room to grow without swapping infrastructure.
- Dual-Voltage AC Input (115/230VAC): Auto-selects between 115VAC/60Hz/1.2A and 230VAC/50-60Hz/0.75A, so the same unit installs in North American and international sites. No separate SKU, no transformer — useful for global integrators stocking a single part number.
- NEMA 4/4X, IP66-11 Enclosure: Rated for rain, hose-directed water, corrosive environments, and windblown dust. This isn't a splash-rated consumer housing — NEMA 4X specifically covers corrosion resistance, meaning coastal and chemical-plant installations are within scope. Wall or pole mount is supported natively.
- -30°C to 70°C Operating Range (30W Mode): Covers extreme cold without a heater kit. At 60W mode the upper limit drops to 55°C — still sufficient for most outdoor deployments, but worth noting in high-ambient environments like rooftop plant rooms. Storage tolerance extends to 85°C.
- 10/100/1000 Mbps Gigabit Passthrough: Auto-negotiating, auto-crossover RJ45 passes full Gigabit throughput up to 100m on Cat5e or better. No bottleneck for 4K or multi-stream cameras — the Ethernet path doesn't become the constraint.
- Integral Surge Protection: Built-in surge protection on the PoE output reduces the risk of camera damage from nearby lightning strikes — relevant for pole-mounted and rooftop camera runs where surge exposure is elevated.
- Dual LED Status Indicators: LED 1 confirms PoE active; LED 2 confirms AC power present. Yellow/green LEDs at the RJ45 jack show IP link status and 10/100Base-T activity. Commissioning and fault diagnosis from the enclosure face without opening a switch rack.
- NDAA and TAA Compliant: Verified for this SKU. NDAA Section 889 compliance is a hard gate on federal security projects; TAA compliance satisfies GSA schedule requirements. Both are confirmed on the NETWAY1DWPM, not inferred from brand-level claims.
Integration and Compatibility
The NETWAY1DWPM fits anywhere a PoE-capable network switch isn't reachable — perimeter fence lines, parking lot poles, loading dock columns, and remote building entry points served by a single Cat5e run from the nearest IDF. It works with any 802.3af/at-compliant IP camera or access point; no proprietary negotiation is required. For pole installations, Altronix offers the PMK1 pole mount kit as a compatible accessory. NEMA-rated wire gland inlets (WG1) are available for clean conduit entry, and a LOCK1WP padlock secures the enclosure against tampering.
When specifying for a larger outdoor IP camera deployment, note that this is a single-port device — one camera per unit. For multi-port outdoor midspan requirements, evaluate higher-port-count units in the Altronix NetWay family. If you're planning camera infrastructure from the ground up, the PoE planning guide covers budget calculations across mixed 15W/30W/60W loads on switch ports versus dedicated midspans.
Frequently Asked Questions
Q: Is the NETWAY1DWPM NDAA Section 889 compliant?
A: Yes. The NETWAY1DWPM carries verified NDAA compliance, making it eligible for federal, state, and education projects where Section 889 supply-chain restrictions apply.
Q: What is the maximum PoE wattage the NETWAY1DWPM can deliver?
A: The NETWAY1DWPM delivers up to 60W on its single port using all four cable pairs. It also operates in IEEE 802.3at (30W) and IEEE 802.3af (15W) modes depending on the connected device's negotiation.
Q: Can the NETWAY1DWPM be pole-mounted?
A: Yes. The enclosure supports both wall and pole mounting. The Altronix PMK1 pole mount kit is a listed compatible accessory for this unit.
Q: What is the operating temperature range of the NETWAY1DWPM?
A: In 30W mode, the NETWAY1DWPM operates from -30°C to 70°C (-22°F to 158°F). In 60W mode, the upper limit is -30°C to 55°C (-22°F to 131°F). Storage temperature range is -30°C to 85°C.
Q: Does the NETWAY1DWPM work with 230VAC power?
A: Yes. The unit accepts both 115VAC/60Hz and 230VAC/50-60Hz input, making it usable in international installations without an external transformer.
Q: What enclosure rating does the NETWAY1DWPM carry?
A: The enclosure is rated NEMA 4/4X and IP66-11, covering rain, hose-directed water, windblown dust, and corrosion — suitable for coastal, industrial, and exposed outdoor locations.
The NETWAY1DWPM earns its place on perimeter camera runs where you genuinely cannot get a PoE switch within 100 meters of the camera. That 60W ceiling — delivered over all four pairs on a standard Cat5e run — is what separates it from a generic 802.3at injector. I've spec'd it on loading dock PTZ installs where the camera draw, combined with a heated enclosure, was pushing 45W; a standard 30W port would have starved it mid-winter.
Technical Highlights:
- 60W Four-Pair Delivery: Full 60W output uses all four cable pairs simultaneously — this is above the 802.3at ceiling and covers high-wattage PTZ cameras and IR illuminators that would otherwise require a separate power supply at the camera.
- NEMA 4/4X + IP66-11 Rating: The corrosion-resistance designation in NEMA 4X matters on coastal sites and anywhere salt air or chemical wash-down is a factor. IP66-11 adds the hose-jet rating, so pressure washing near the enclosure during facility maintenance isn't a concern.
- -30°C Low-End Thermal Floor: At 30W mode the unit is rated to -30°C with no heater — relevant for northern-climate outdoor deployments where competitors' midspans require a cold-weather kit to operate reliably through winter.
Deployment Considerations:
- At 60W mode, the upper temperature limit drops from 70°C to 55°C. In rooftop enclosures that see solar gain in summer, verify ambient temperatures don't exceed that ceiling before committing to 60W operation — or spec a shaded or ventilated mounting location.
- This is a single-port device. If you have two or more cameras at the same pole or junction box, you will need one unit per camera run. Factor that into your BOM early — stacking multiple NETWAY1DWPMs on one pole is achievable with the PMK1 kit, but space and cable routing need to be planned at the design stage.
The NETWAY1DWPM is the right call on isolated perimeter camera poles — parking lots, fence lines, building entry points — especially on NDAA- or TAA-required government and education projects where the power injection device itself must pass supply-chain scrutiny, not just the camera.
