Panduit CJSLR688TGYLY Mini-Com Cat 6 Shielded 45° Angled RJ45 Jack Module
The Panduit CJSLR688TGYLY is a Mini-Com Cat 6 shielded RJ45 jack module engineered with a 45° left/right angled termination geometry to solve cable routing challenges in high-density patch panels, shallow wall boxes, and equipment racks where standard straight-entry jacks force excessive bend radius. Built for shielded twisted pair (STP) installations requiring noise immunity—security camera uplinks, PoE-fed access control panels, and industrial Ethernet runs—this module delivers TG (Tool-Guide) termination that eliminates punch-down tools while maintaining 100% factory-tested performance exceeding ANSI/TIA-568.2-D Category 6 channel and component specifications. Yellow insulator enables instant visual identification in mixed-category or VLAN-segregated faceplate deployments.
Key Features
- 45° left/right angled termination geometry reduces cable stress and bend radius in shallow boxes and high-density panels
- TG (Tool-Guide) termination system—wire insertion without punch-down tools, gas-tight IDC contacts maintain connection integrity
- Shielded RJ45 jack with 360° metallic coupling supports Cat 6 performance over 4-pair 22-26 AWG STP cable
- Supports IEEE 802.3bt Type 3 (60W) and Type 4 (90W) PoE++ over 2,500 connection cycles—tested for high-draw PTZ cameras and wireless access points
- 100% factory tested and individually serialized for end-to-end traceability in structured cabling documentation
- Exceeds ANSI/TIA-568.2-D and ISO 11801 Category 6 channel performance; meets IEC 60603-7 connector durability standard
- Yellow insulator for rapid visual identification in multi-category or VLAN-coded installations
- UL 1863 and UL 2043 plenum-rated (flame/smoke), RoHS compliant for municipal and federal project specifications
- Compatible with all Mini-Com modular faceplates, patch panels, and surface-mount boxes—no proprietary adapters required
The 45° angled entry point rotates the cable path 45° left or right relative to the jack body, positioning the conductors parallel to shallow wall cavities or rack panel depth instead of forcing a sharp 90° turn immediately behind the connector. In single-gang boxes housing four or six Mini-Com jacks, this geometry reclaims the 1.5–2 inches of clearance typically consumed by bend radius, preventing jacket kinking that degrades return loss and near-end crosstalk (NEXT). The TG termination system uses color-coded wire guides and a captive retention cap—strip the cable jacket, insert each conductor into its marked slot, and snap the cap closed to drive wires into gas-tight insulation-displacement contacts. No impact tool, no blade depth adjustment, no risk of over-seating that fractures conductors. Field termination time averages under 90 seconds per jack, and the captive design prevents loose components during overhead or ladder-top installations. The shielded architecture bonds the module's die-cast frame to the cable's foil and drain wire, maintaining the shield path through the RJ45 plug's metallic shell to suppress EMI from fluorescent ballasts, VFD motor controllers, and adjacent power conductors common in industrial and healthcare environments.
Deploy the CJSLR688TGYLY in surveillance headend racks where densely populated patch panels push Cat 6 cable bundles against rear wire management—straight jacks force a 90° turn that violates the 4× cable diameter minimum bend radius, but the angled geometry allows a smooth arc. Use yellow insulators to designate camera VLAN ports in access control faceplates that mix low-voltage door contacts (white/gray) and PoE-fed card readers (yellow) in a single four-gang box, enabling technicians to identify powered ports without a toner. The 2,500-cycle durability rating supports high-turnover endpoints—wireless AP closets that swap APs during tech refreshes, visitor kiosks where surge events force NIC replacements, and lab benches where daily plug/unplug cycles test camera configurations. Each jack ships with a laser-etched serial number on the front bezel; scan it into your DCIM or CMMS to track which physical jack terminates which cable ID, critical for change-order documentation in hospitals, airports, and data centers where cable plant traceability satisfies audit requirements. The module's 18 mm height and 15.7 mm width fit standard Mini-Com faceplate and patch panel cutouts—retrofit existing Panduit installs without replacing faceplates, or mix angled and straight jacks in the same panel to optimize routing per port location.
UL 2043 plenum rating qualifies the jack for installation in air-handling spaces without conduit in buildings governed by NFPA 90A and IBC Chapter 8, eliminating the labor and material cost of EMT runs in above-ceiling camera deployments. Exceeding TIA-568.2-D component specifications across insertion loss, return loss, and NEXT provides 3–6 dB margin above the minimum pass threshold, absorbing performance degradation from dust intrusion, connector wear, and cable jacket UV aging over a 10–15 year service life. IEEE 802.3bt Type 4 compliance at 2,500 cycles confirms the jack maintains contact resistance below 20 milliohms under sustained 90W PoE load—critical for PTZ cameras with IR arrays and heaters that draw peak power during cold-weather night operations. For installations requiring FIPS 199 moderate-impact traceability or GSA schedule compliance, the individual serial number and 100% factory test report provide the auditable documentation that batch-tested commodity jacks cannot.
