Lenovo 4X97A87134 SR630 V3 SAS/SATA + AnyBay NVMe Storage Cable
Overview
The Lenovo 4X97A87134 is a purpose-built internal storage cable for the ThinkSystem SR630 V3 rack server, providing six SAS/SATA connections plus four AnyBay NVMe lanes in a single routed assembly. If you are configuring or expanding storage in an SR630 V3 chassis, this is the cable that bridges the backplane to the system board — it is not a generic cable and will not interchange with other ThinkSystem generations or form factors.
Server storage cabling is one of those details that looks minor until it stops a build. The 4X97A87134 is a factory-matched cable designed to fit the SR630 V3 chassis routing, connector positions, and signal requirements without modification or improvisation.
Key Features
- Dual-interface design (NVMe + SATA): Supporting both NVMe and SATA drive protocols in the same cable run means you can populate AnyBay bays with either NVMe SSDs for latency-sensitive workloads or SATA drives for capacity — without swapping cables when your drive mix changes.
- 6×SAS/SATA + 4×AnyBay NVMe layout: The six SAS/SATA connections cover your conventional spinning or solid-state drives, while the four AnyBay positions give flexibility to assign those bays based on actual workload demand rather than fixed protocol slots.
- SR630 V3 chassis-specific fit: Lenovo validates cable assemblies per chassis generation. Using 4X97A87134 means connector keying, latch retention, and signal integrity are confirmed for the SR630 V3 — substituting an unvalidated cable risks intermittent drive detection or outright signal errors under load.
- UNSPSC 26121624 classification: This code places the part in the electronic cable and wire category, useful for procurement teams routing purchase orders through commodity-coded approval workflows.
Integration and Compatibility
The 4X97A87134 is engineered specifically for the Lenovo ThinkSystem SR630 V3. It is not listed as compatible with SR630 V2 or earlier SR630 platforms — the backplane connector layout and chassis routing differ across generations. Before ordering, confirm your chassis is the V3 revision. If you are building out a mixed NVMe/SATA storage tier on the SR630 V3, this cable supports that configuration natively without an adapter or riser interposer.
For surveillance infrastructure teams deploying SR630 V3 servers as NVR backend hosts, video management appliances, or edge analytics nodes, the AnyBay NVMe lanes are particularly relevant — NVMe-backed storage can sustain the high sequential write throughput that multi-channel video recording demands, while the SATA positions handle archive or redundancy drives cost-effectively in the same enclosure.
Frequently Asked Questions
Q: Is the 4X97A87134 compatible with the Lenovo ThinkSystem SR630 V2?
A: Evidence only confirms compatibility with the SR630 V3. The SR630 V2 uses a different chassis generation with different backplane and routing specifications. Do not assume cross-generation compatibility without verifying with Lenovo's parts compatibility tool.
Q: Does the 4X97A87134 support both NVMe and SATA drives simultaneously?
A: Yes. The cable assembly provides six SAS/SATA connections and four AnyBay NVMe positions, supporting mixed drive populations in the SR630 V3 chassis in a single cable run.
Q: What does 'AnyBay' mean in the context of this cable?
A: AnyBay is Lenovo's term for drive bays that can accept either NVMe or SATA/SAS drives depending on the cable and backplane installed. The 4X97A87134 enables the AnyBay positions on the SR630 V3 to operate in NVMe mode.
Q: Can this cable be used in a non-Lenovo server chassis?
A: No. This is a chassis-specific internal cable validated for the SR630 V3 form factor, connector positions, and signal routing. It will not fit or function correctly in third-party server chassis.
When I see builds stall at the storage cabling stage, it is almost always because someone ordered a cable from a different SR630 generation or tried to adapt a generic SAS cable. The 4X97A87134 is the correct assembly for the SR630 V3 — it provides both the six SAS/SATA runs and the four AnyBay NVMe lanes the V3 backplane expects, and it routes to the chassis geometry without forcing connectors.
Technical Highlights:
- NVMe + SATA dual protocol: Four AnyBay NVMe lanes alongside six SAS/SATA connections means you can run NVMe SSDs in the latency-critical bays and SATA in the capacity bays — one cable, one build, no protocol compromise.
- SR630 V3 chassis validation: Lenovo validates cable assemblies per chassis generation. The 4X97A87134 is confirmed for V3 connector keying and signal routing — no guesswork on drive detection reliability.
- UNSPSC 26121624: The commodity code is procurement-useful for enterprise buyers routing orders through coded approval workflows without manual category assignment.
Deployment Considerations:
- Confirm your chassis is specifically the SR630 V3 before ordering — V2 and V3 share the SR630 name but differ in backplane layout and internal routing. Cross-generation cable substitution is not supported.
- This cable enables AnyBay bays in NVMe mode; if your workload calls for all-SATA population, verify whether the standard SATA-only cable variant is the more appropriate part for your configuration.
For SR630 V3 deployments running video management software or surveillance analytics workloads, the NVMe AnyBay positions this cable enables are the right path for write-intensive recording tiers — sustained sequential throughput on NVMe holds up under multi-channel camera ingestion in a way that SATA alone will not.
