Panduit LDPH10IW8-A Pan-Way Power-Rated Hinged Surface Raceway, 8 ft
Overview
The Panduit LDPH10IW8-A is an 8-foot, two-piece interlocking surface raceway from the Panduit Pan-Way™ line — built for installations where low-voltage cabling needs to run cleanly along walls, baseboards, or ceilings without conduit penetrations or in-wall rough-in. At 1.52 in wide by 0.86 in deep (39mm × 22mm), it's sized for moderate cable bundles: think IP camera drops, access control home-runs, or structured cabling tails at workstations. The LDPH10IW8-A (often searched as LDPH10IW8 A) is rated for circuits up to 600V and carries UL5A listing, making it suitable for both low-voltage data runs and power feeds in the same raceway where your AHJ requires listed management.
Key Features
- Two-Piece Hinged Design (1.52" × 0.86"): The interlocking base-and-cover construction lets you lay all cables in the open base channel first, then snap the cover closed — no threading wire through a closed tube. On retrofit jobs where you're adding camera or reader drops after walls are finished, this shaves significant labor time versus pulling through a full conduit.
- 600V Power Rating: Rated for up to 600V circuits, the LDPH10IW8-A qualifies for mixed low-voltage and mains-power routing where code allows combined raceway. If your installation separates power and data physically, this rating also provides headroom for PoE switch feeds or UPS output runs.
- Factory-Applied Adhesive: Adhesive is pre-applied at the factory on the base channel, so mounting on smooth drywall, painted CMU, or tile requires no separate adhesive step. This matters on office-fit installations where speed of deployment is billed by the hour — score, peel, press, done.
- Pre-Punched Mounting Holes: Knockout-style mounting holes are already in the base, giving you the option to mechanically fasten to studs or hard surfaces in addition to (or instead of) the adhesive. In high-traffic areas or where the adhesive bond might degrade over time, screw-down fastening keeps the raceway anchored.
- UL5A Listed / TIA/EIA Compliant / UL94V-0 Flame Rating: UL5A listing means this raceway has been independently verified for use as a surface cable management system — relevant when submitting to an AHJ for permit or when your customer's insurance carrier requires listed components. UL94V-0 and FT4 flame ratings confirm the PVC compound self-extinguishes, which matters in plenum-adjacent or commercial occupancy installs where fire propagation through cable management is a code concern.
- Compatible with Mini-Com™ and Surface-Mount Electrical Boxes: The LDPH10IW8-A terminates cleanly into Panduit Mini-Com™ surface raceway outlet boxes and standard surface-mount electrical boxes, so you can run the raceway to a structured outlet at a desk or camera junction point without transition adapters or custom cuts.
- Bone White (Ivory) Finish: The bone white color blends with standard commercial interior finishes. Not a match for bright white or off-white walls, but acceptable in most office and light commercial environments. Paint-over is an option if color-match is required.
- 8 ft Sticks, Sold in Packs of 8 (20-Piece MOQ): Each stick covers 8 linear feet (2.4m). The package quantity of 8 sticks covers 64 linear feet per pack — appropriate for a single medium-length camera drop or a few short office runs. Carton quantity is 160 pieces, relevant for larger projects buying in bulk through distribution.
Integration and Compatibility
The LDPH10IW8-A is designed as part of the Pan-Way surface raceway system, which includes a full accessory ecosystem: inside corners, outside corners, flat elbows, couplings, and end caps that share the same 1.52 in × 0.86 in profile. Plan your full run with the matching LDPH-series fittings to avoid profile mismatches at transitions. The two-piece design is specifically called out as compatible with LDPH-series components.
For structured cabling terminations, the raceway exits into Panduit Mini-Com™ surface-mount boxes or standard surface electrical boxes — standard practice on structured cabling deployments where you want a finished outlet face rather than a raw cable exit. This makes the LDPH10IW8-A a natural fit on security integrator jobs where IP camera cables, reader cables, or VoIP phone drops need to be routed neatly in occupied tenant spaces.
Material is PVC throughout, so cutting to length in the field uses a standard miter box or fine-tooth handsaw. No metal burrs, no conduit bender required.
Frequently Asked Questions
Q: What is the maximum voltage rating for the LDPH10IW8-A?
A: The LDPH10IW8-A is rated for circuits up to 600V, and it carries UL5A listing for surface raceway applications. This makes it suitable for both low-voltage data/control wiring and mains power runs where a listed raceway is required.
Q: Does the LDPH10IW8-A include mounting adhesive, or do I need to purchase it separately?
A: Factory-applied adhesive is pre-installed on the base channel — no separate adhesive purchase or field application is needed. Mechanical mounting via the pre-punched holes is also available for hard surfaces or high-traffic areas.
Q: What are the exact dimensions of the LDPH10IW8-A channel?
A: The channel is 1.52 inches wide (39mm) by 0.86 inches deep (21.8mm), and each stick is 8 feet (2.4m) long. The two-piece hinged design means the internal usable cross-section is approximately that full width and depth once the cover is closed.
Q: What certifications does the LDPH10IW8-A carry?
A: It meets UL94V-0 and FT4 flame ratings, is listed UL5A, and complies with TIA/EIA raceway standards. These listings cover flame propagation, surface raceway installation requirements, and structured cabling infrastructure standards.
Q: How many sticks come in a package, and how much linear footage does one package cover?
A: Each package contains 8 sticks at 8 feet each, covering 64 linear feet per pack. The minimum order quantity (MOQ) is 20 pieces; the carton quantity is 160 pieces for bulk distribution orders.
Q: Can the LDPH10IW8-A be used with Panduit Mini-Com outlet boxes?
A: Yes. The LDPH10IW8-A is specifically designed to terminate into Panduit Mini-Com™ surface-mount outlet boxes and standard surface electrical boxes, enabling a finished structured outlet at the end of a raceway run.
The LDPH10IW8-A is a product I reach for specifically when a job calls for a 600V-rated, UL5A-listed surface raceway in a finished interior space — not because it's the only option, but because the factory-applied adhesive and pre-punched holes together mean the base goes up fast without a separate adhesive step, and the two-piece hinged design lets you load the entire cable bundle before you snap the cover. On a 200-foot camera drop retrofit through an occupied office, that combination is a real labor-saver.
Technical Highlights:
- 600V Rating + UL5A Listing: Most low-voltage surface raceway is unlisted or listed only for low-voltage — UL5A covers this one for mains-voltage circuits too, which matters when your AHJ wants listed components on a permit pull or when the job spec explicitly calls for listed raceway.
- 1.52" × 0.86" Internal Profile: At 39mm wide by 21.8mm deep, this channel comfortably handles a handful of Cat6 runs or a mix of Cat6 plus a few 18/2 or 22/4 control cables. It's not a high-density cable tray — if you're routing 10+ cables, look at a wider profile in the Pan-Way line.
- UL94V-0 / FT4 Flame Rating: The PVC compound self-extinguishes per UL94V-0 and passes FT4 vertical flame spread. In light commercial occupancies where the AHJ scrutinizes cable management materials, having that rating in the submittal documentation removes a common objection.
Deployment Considerations:
- The factory adhesive bonds well to smooth painted drywall and tile, but on textured or porous surfaces (rough CMU, unpainted concrete), plan to supplement with the pre-punched mechanical fastener holes. Adhesive-only on rough surfaces will eventually let go under cable weight.
- The 8-ft stick length means you'll have joints approximately every 8 feet on long runs — use the matching LDPH-series couplings to maintain profile alignment and avoid the raceway pulling apart at joints over time. Don't improvise with generic PVC conduit fittings; the profile won't match and the cover won't seat flush.
The LDPH10IW8-A is the right specification for IP security camera cable drops and access control reader runs in tenant improvement or office retrofit projects where a finished appearance is required and open conduit isn't acceptable to the end user. It's not a high-density solution — keep it to light cable bundles and complement it with the full Pan-Way fitting system for a clean, professional installation.
