Vertiv HMX5200R-001 Dual DVI-D USB KVM Receiver with Audio and SFP
Overview
The Vertiv HMX5200R-001 is the receiver unit in the Vertiv HMX KVM-over-IP extender series, designed for data center operators, broadcast engineers, and secure facility integrators who need to extend dual-display workstation access over a standard IP network without sacrificing resolution or USB peripheral support. Operating as the remote desktop endpoint, the HMX5200R-001 delivers 1920x1200 video across two DVI-D outputs simultaneously — useful in control rooms where operators need wide-format or dual-monitor layouts at full native resolution. It pairs with an HMX transmitter unit at the host computer, turning any standard IP LAN or dedicated switch fabric into a high-performance KVM extension path. For organizations evaluating Vertiv KVM and infrastructure solutions, this receiver is a purpose-built endpoint for that architecture.
Key Features
- Dual DVI-D Video at 1920x1200: Two independent DVI-D outputs let you drive a full dual-monitor workstation session from a remote location — no resolution scaling, no compression artifacts on static content. At 1920x1200 per display, you have enough pixel density for detailed engineering diagrams, video walls, or financial trading layouts where a 1080p crop would cut off information.
- Four USB 2.0 Type-A Ports with Class Control: The HMX5200R-001 provides 4x USB Type-A ports with USB 2.0 hub support and Class Control, meaning you can connect keyboards, mice, card readers, and USB audio devices at the receiver while the host computer sees them as directly attached peripherals. Class Control lets administrators whitelist or restrict device categories — relevant in secure environments where uncontrolled USB mass storage is a policy risk.
- Integrated Audio I/O (Speaker and Mic): Built-in audio output and microphone support means operators can participate in voice communications or receive system audio alerts without a separate audio extender. This simplifies operator console builds in NOC, SOC, and broadcast control room environments where every cable run matters.
- Dual RJ45 Network Interfaces: Two network ports give you deployment flexibility — one for the primary KVM data path, one for management or redundant network connection. In environments where network uptime is non-negotiable, dual NICs reduce single-point-of-failure exposure at the endpoint.
- SFP-Ready Architecture: The HMX series supports SFP modules for fiber uplinks, which matters when the receiver is located more than 100 meters from the nearest switch or when copper runs through electrically noisy environments (generator rooms, substations). Fiber extends the reach without signal degradation.
- Compact Form Factor — 7.92 x 6 x 1.76 in, 2.7 lb: The HMX5200R-001 is desk- or rack-adjacent sized, light enough to mount behind a monitor or on a thin client shelf. At 2.7 lb it won't strain cable management arms or VESA mount adapters.
- 5VDC, 20W via External Power Adapter: Power comes from the included adapter rather than PoE, which simplifies deployment on existing Ethernet infrastructure that may not have PoE budget headroom. The 20W ceiling is well within what a standard wall outlet or UPS strip handles without load planning.
- CE and FCC Certified: Agency approvals for North American and European markets mean the unit can ship into both regions without additional compliance review — useful for multinational deployments or integrators serving global enterprise accounts.
- Operating Range 0–40°C / 32–104°F: Rated for standard indoor climate-controlled environments. Not a hardened industrial unit — plan for air-conditioned operator console rooms, control centers, or server-adjacent spaces rather than factory floors or outdoor enclosures.
Integration and Compatibility
The HMX5200R-001 is the receiver half of a paired HMX extender system. It requires a compatible HMX transmitter unit installed at the host workstation or server; the two communicate over your IP network infrastructure, including standard Cat5e/Cat6 copper or fiber via SFP. USB 2.0 Class Control is enforced at the receiver, so device policy is manageable without host-side software agents. For KVM switches and extenders, this unit slots into structured deployments where centralized compute needs to be accessed from physically separated operator positions. Integrators building out data center infrastructure with centralized compute and distributed operator consoles will find the dual-NIC and dual-display spec combination practical for high-density control environments. Review your power distribution layout to confirm wall-outlet or UPS tap availability at each receiver location, since PoE is not supported. When planning a multi-seat deployment, cross-reference the HMX transmitter SKU compatibility list from Vertiv to confirm firmware parity between TX and RX units — mismatched firmware versions are a common commissioning issue on HMX deployments. For additional KVM planning resources, consult a KVM extender selection guide to match bandwidth and latency requirements to your network fabric.
Frequently Asked Questions
Q: What transmitter unit pairs with the HMX5200R-001?
A: The HMX5200R-001 is the receiver unit and requires a compatible Vertiv HMX transmitter (TX) unit installed at the host computer. Consult the Vertiv HMX compatibility matrix to confirm the correct TX SKU for your host connection type (DVI-D dual-output workstation).
Q: Does the HMX5200R-001 support 4K or DisplayPort displays?
A: No. The HMX5200R-001 is rated for a maximum video resolution of 1920x1200 per DVI-D output. It does not support 4K, DisplayPort, or HDMI natively — a DVI-to-HDMI passive adapter can connect compatible monitors but will not extend resolution beyond 1920x1200.
Q: Can USB storage devices be connected to the HMX5200R-001?
A: The unit includes USB 2.0 Class Control, which allows administrators to restrict USB device classes — including mass storage — at the receiver. Whether USB storage is permitted depends on the Class Control policy configured for your deployment.
Q: Does the HMX5200R-001 support PoE for power?
A: No. The HMX5200R-001 is powered by an external 5VDC power adapter with a 20W output. It does not draw power from the Ethernet port and requires a dedicated power supply at the receiver location.
Q: What are the environmental operating limits for the HMX5200R-001?
A: The unit is rated for operation between 0°C and 40°C (32°F to 104°F) at 10%–90% non-condensing humidity. Storage temperature extends from -35°C to 70°C (-31°F to 158°F). It is designed for climate-controlled indoor environments only.
Q: Is the HMX5200R-001 CE and FCC certified?
A: Yes. The HMX5200R-001 carries both CE and FCC agency approvals, covering North American and European regulatory requirements.
The HMX5200R-001 is a receiver I'd spec for broadcast and government control room builds where the operator position is decoupled from the compute rack — specifically because of the dual DVI-D outputs at 1920x1200 and the 4-port USB 2.0 hub with Class Control. That combination gives you a full dual-monitor operator seat with enforced USB device policy, which is the kind of thing security-conscious facilities want baked in at the hardware layer rather than managed purely by software.
Technical Highlights:
- 1920x1200 Dual DVI-D: Full WUXGA resolution on both outputs — that's 20% more vertical pixels than 1080p, which matters when operators are running two information-dense windows side by side and need to see rows at the bottom of the screen without scrolling.
- USB 2.0 Class Control: Restricts device categories (mass storage, audio, HID, etc.) at the port level — no host-side software agent required. In a cleared facility or financial trading environment, this is a hardware-enforced USB control that simplifies compliance documentation.
- Dual RJ45 with SFP support: Two network interfaces give you a primary-plus-management or active-redundant network path depending on HMX system configuration. SFP support means a fiber uplink is an option when the receiver sits more than 100m from the nearest switch.
Deployment Considerations:
- Plan a wall outlet or UPS tap at every receiver position — the HMX5200R-001 runs on a 5VDC 20W external adapter and has no PoE fallback, so your cable run needs a power source at the remote end, not just Ethernet.
- Operating temperature tops out at 40°C (104°F) — this is a climate-controlled-indoor-only unit. Don't drop it into an unventilated AV rack in a mechanical room or anywhere without active cooling.
Best fit for centralized-compute control rooms — NOC, SOC, broadcast master control, or government ops centers — where operators need full dual-display sessions at distance from the server rack and USB device control is a compliance requirement, not an afterthought. The HMX5200R-001 (often searched as HMX5200R 001) handles that scenario cleanly when paired with the correct HMX transmitter at the host end.
