Panduit P12B01M G5 Basic PDU

The Panduit P12B01M is a 1U horizontal basic PDU engineered for rack-mount power distribution in surveillance equipment rooms, network closets, and IT infrastructure deployments. This G5-series unit delivers 120V single-phase power across twelve NEMA 5-20R outlets, fed by a NEMA 5-15P input plug on a 3-meter (10-foot) power cord. The 15-amp circuit capacity supports mixed loads of PoE switches, NVRs, workstations, and ancillary equipment without requiring separate branch circuits for every device. Black powder-coated metal housing provides durability in rack environments where equipment churn and cable management create ongoing contact risk.

Key Features

• Twelve NEMA 5-20R outlets on 15A circuit — supports twelve low-draw devices or mixed load up to 1800W total (derate to 1440W continuous per NEC 80% rule)
• NEMA 5-15P input with 10-foot cord — reaches distant wall or floor outlets without requiring in-rack receptacles or cord extensions
• 1.7-inch (44mm) height, 17.5-inch (444mm) width — mounts horizontally in standard 19-inch racks with minimal vertical space consumption
• Powder-coated metal construction — resists scratches, corrosion, and impact during installation or equipment moves
• UL listed (file E218078) — meets NEC Article 645 requirements for information technology equipment rooms

Each 5-20R outlet accepts both 5-15P (standard three-prong) and 5-20P (T-slot horizontal blade) plugs, providing compatibility with modern PoE switches that ship with 5-20P cords to signal 20A capability even when actual draw is lower. The 15A branch circuit limits total continuous load to 12 amps (1440W) per NEC 210.20(A), which typically supports four to six enterprise PoE switches (each drawing 200-350W under mixed PoE+/PoE++ camera loads), one 4-bay NVR (150-250W), and ancillary devices like KVM switches or management appliances. Integrators installing high-density PoE environments — such as a 24-port switch delivering PoE++ (90W per port) to PTZ cameras — should calculate actual draw: a fully loaded 24-port PoE++ switch can pull 2160W, exceeding this PDU's circuit capacity and requiring a 20A or dual-circuit PDU instead. The P12B01M fits surveillance control rooms where camera counts stay below 48 total (two 24-port switches at partial PoE load) or where NVR and switch loads combined stay under 1400W continuous.

The 10-foot input cord mitigates the common problem of rack placement dictated by wall outlet proximity. Equipment racks in retrofitted buildings often sit four to eight feet from the nearest 120V duplex, forcing integrators to either relocate the rack (expensive, disruptive) or daisy-chain extension cords (code violation in commercial spaces per NEC 400.8). The P12B01M's factory-attached cord eliminates that tension, reaching floor boxes, wall outlets behind adjacent desks, or ceiling-fed Wiremold drops without aftermarket extensions. The NEMA 5-15P plug is compatible with standard 15A or 20A branch circuits; installers should verify the upstream breaker matches the planned continuous load (15A breaker for up to 12A continuous, 20A breaker for up to 16A continuous).

Horizontal 1U mounting places outlets along the front face of the rack, accessible without reaching behind equipment. This front-access layout simplifies plug/unplug operations during maintenance windows — no need to remove adjacent devices or disturb cable dressing to swap a failed switch. The 17.5-inch width leaves approximately 0.75 inches of clearance on each side within a standard 19-inch rack opening, enough room for finger access to the outermost outlets but tight enough that offset mounting brackets or keyhole slots may be required depending on the rack rail system (Panduit specifies mounting hardware separately; confirm compatibility with your EIA-310 rack before ordering). Powder-coated finish resists the paint chips and edge rust common on cheaper stamped-steel PDUs, maintaining appearance and electrical safety over multi-year deployments in dusty or high-humidity equipment rooms.

UL listing under file E218078 confirms compliance with UL 1363 (relocatable power taps) and UL 60950-1 / 62368-1 (IT equipment safety), required for code inspections in commercial buildings, data centers, and any space governed by NFPA 70 (National Electrical Code) Article 645. Jurisdictions enforcing Article 645 mandate that all power distribution equipment in IT rooms carry UL or equivalent NRTL certification; the P12B01M satisfies that requirement for basic (non-monitored, non-switched) power distribution. Integrators working in healthcare (NEC Article 517), education, or government facilities should verify that "basic PDU" meets the site's specific requirements — some contracts mandate metered or network-managed PDUs for energy monitoring or remote reboot capability, which the P12B01M does not provide.