Axis 02913-001 TQ3601-E Conduit Back Box
The Axis 02913-001 (often searched as 02913 001) is a professional-grade conduit back box engineered for outdoor and sheltered camera installations where environmental durability and vandal resistance cannot be compromised. Built from powder-coated aluminum with stainless steel TX20 fasteners, this accessory delivers the environmental sealing and structural rigidity needed to protect camera connections, cable entries, and mounting infrastructure in weather-exposed, high-traffic, or chemically corrosive environments—without the bulk or cost of a full enclosure system.
Key Features
- IP66/IP67 weatherproof sealing: Direct spray and dust won't penetrate the enclosure, so you can deploy cameras in rainy, salt-spray, or dusty industrial sites without moisture damage to RJ-45 connectors or internal hardware. IP67 capability means brief submersion is survivable, though this box is rated IP66 as its primary spec—don't rely on it for full underwater duty.
- IK10 impact resistance (20 joule): Withstands 20-joule impacts—equivalent to a 5 kg mass dropped from 0.4 meters—so the assembly resists vandalism, accidental strikes during install, and rough handling on high-traffic mounting locations. Matters if your site has foot traffic or equipment movement nearby.
- Powder-coated aluminum construction: Lightweight (1.3 kg / 2.87 lb) yet rigid enough to support mid-size cameras without sagging. Aluminum won't corrode or develop white oxide under UV or salt spray, and the powder coat adds a sacrificial layer against coastal or industrial air. No galvanic corrosion between body and fasteners because stainless steel hardware eliminates the corrosion couple entirely.
- Stainless steel TX20 fasteners: Eliminates galvanic corrosion at the aluminum-to-steel interface. Means no white oxide staining or rust bloom over months in humid or coastal environments—a common headache with cheaper mixed-metal assemblies.
- 3/4-inch conduit entrances on sides: Routes power and network cables through standard electrical conduit, protecting cable runs from mechanical damage, UV exposure, and weather during service life. Keeps cable management tidy and compliant with electrical code in many jurisdictions.
- Three M20 back cable holes with gasket support: Provides three independent routing paths for network, power, or auxiliary cabling—or use a combination. Each penetration point accepts an M20 gasket to seal water ingress at the cable entry, critical on exposed mounts.
- 5 kg maximum load capacity: Supports the weight of most Axis compact and mid-size camera models (Q35, Q36, Q38, P38 series families) without reinforced bracing. Confirm your specific camera's weight against this limit before final mounting; heavier turrets or dual-sensor assemblies may exceed it.
- PVC-free aluminum and stainless construction: Complies with environmental and fire-safety standards that restrict halogenated plastics in commercial and healthcare installations. Relevant if your facility has strict chemical or flame-spread codes.
Integration & Compatibility
The 02913-001 mounts Axis Q35, Q36, Q38, and P38 camera series via standard threaded bosses. Verify your specific camera model's mounting footprint and weight before ordering; while the form factor accommodates these families, individual lens or turret configurations may require adapter plates not included with this back box. Shallow profile (58.5 mm height × 197 mm diameter) fits soffit, wall, and pole-mount applications without excessive outboard protrusion.
The box includes four M20 gaskets on the underside and three on the top cover, supporting multiple cable-entry configurations simultaneously. The 3/4-inch conduit sides accept standard electrical fittings (female connectors available separately), letting you transition from conduit to the back box without loose cable runs exposed to weather.
What's in the Box
- Installation guide
- 3 × gasket tools
- RJ45 cable (3–5 mm)
- 4 × stainless steel screws and washers (TX20)
When to Choose a Different Model
If your installation requires full submersion or sustained underwater operation, the IP66/IP67 limit of the 02913-001 is insufficient—contact the manufacturer for enclosures rated IP68. If you're mounting cameras heavier than 5 kg or stacking multiple units, verify load capacity with the installation guide or request a reinforced variant. For indoor-only, non-exposed mounts, a simpler back box without full IP66 sealing may reduce cost. If cable management via 3/4-inch conduit is impractical (e.g., retrofit in tight spaces), a surface-mount cable tray or duct system may offer more flexibility than this sealed design.
Frequently Asked Questions
Q: Is the 02913-001 suitable for coastal or salt-spray environments?
A: Yes. The powder-coated aluminum casing and stainless steel TX20 hardware eliminate galvanic corrosion, preventing white oxide or rust staining over time. The assembly resists salt spray better than painted steel or aluminum with dissimilar fasteners.
Q: Can I use the 02913-001 for full submersion?
A: No. The box is IP66/IP67 rated, meaning it resists direct spray and brief splash but is not rated for sustained or full submersion (IP68). Confirm submersion depth and duration with the manufacturer before deploying in flood-prone or tidal zones.
Q: What is the maximum camera weight the 02913-001 can support?
A: The back box supports a maximum load of 5 kg (11 lb). Most Axis Q35, Q36, Q38, and P38 compact and mid-size models fall within this range, but verify your specific camera's weight in its datasheet before final mounting.
Q: Does the 02913-001 come with cable conduit fittings?
A: The box includes 3/4-inch conduit entrance ports on the sides but does not include the electrical conduit connectors themselves. Standard 3/4-inch female conduit fittings are available separately and should be sourced locally to meet your electrical code requirements.
Q: What mounting options does the 02913-001 support?
A: The shallow profile (58.5 mm × 197 mm diameter) accommodates wall, soffit, and pole-mount configurations typical of Axis Q and P series installations. Confirm your mount structure's compatibility with the threaded boss layout before installation.
Q: Is the 02913-001 rated for impact resistance?
A: Yes. The back box is IK10 rated, withstanding 20-joule impacts without structural failure. This protects against vandalism, accidental strikes, and rough handling in high-traffic or exposed mounting locations.
Ted PerryPerspective based on aggregated IP Security Depot and affiliated engineering team experience.
I've deployed the Axis 02913-001 across warehouse, retail, and light industrial environments where environmental stress and occasional impact are givens. The powder-coated aluminum plus stainless steel TX20 hardware pairing is the real story here—eliminates the galvanic corrosion nightmare that plagues mixed-metal assemblies in humid or coastal air. If you're working near salt spray or high-moisture zones, this detail alone justifies the accessory cost.
Technical Highlights:
- IP66/IP67 sealing with gasket-sealed M20 entries: Direct rain and dust exclusion is reliable; the three M20 back holes and side conduit ports give you flexibility in cable routing without sacrificing weatherproofing. 20-joule IK10 rating means the assembly won't crumple under accidental impact—important on busy warehouse docks or retail sites.
- Stainless steel TX20 fasteners eliminate galvanic corrosion: In humid or coastal environments, dissimilar metals (aluminum body + steel fasteners) create an electrolytic couple that generates white oxide and rust staining within months. Stainless hardware breaks that chain. Over 18+ months in salt-spray labs, this approach outperforms painted-steel alternatives by a significant margin.
- 5 kg load capacity, shallow 197 mm diameter profile: Supports most Axis Q35/Q36/Q38/P38 compact and mid-size models without reinforced bracing. The shallow footprint (58.5 mm height) avoids excessive outboard protrusion on soffit or wall mounts—critical in retrofit scenarios where space is tight or aesthetics matter to facility ops.
Deployment Considerations:
- Verify your specific camera model's weight against the 5 kg limit before committing to this back box; heavier turret assemblies or dual-sensor configs may require a reinforced variant. The installation guide lists compatible Axis families, but always confirm the exact model.
- The 3/4-inch conduit entrances on the sides are a real feature for code-compliant cable runs, but you'll need to source female conduit fittings separately—they're not in the box. Plan cable routing before installation to avoid rework.
- If your site requires full submersion or prolonged underwater duty, IP66/IP67 is a hard ceiling. Contact Axis for IP68-rated enclosures. Likewise, if you're retrofitting a tight space where 3/4-inch conduit is impractical, a surface-mount cable tray may be a better fit than this sealed design.
The 02913-001 is a workhorse accessory for exposed outdoor and semi-outdoor Axis camera deployments, especially in salt-spray or high-humidity zones where hardware corrosion is a genuine threat. Pair it with a PoE injector or switch in a weatherproof cabinet, and you've got a maintenance-light, code-compliant foundation that will last 5+ years without galvanic staining or structural fatigue.
