Mounting Brackets & Kits for IP Cameras

Plan Your Deployment

Wall, ceiling, pole, or corner mounting requirements
Indoor vs outdoor environmental exposure
Device model compatibility and load capacity
Vandal resistance and tamper considerations
Future service access and cable routing planning

Sub categories

Showing Results for Mounting Brackets & Kits

Compare

Out of stock
Vivotek

SKU: AM-10G

Vivotek AM-10G Recessed Mounting Kit

Recessed mount for SC9133 camera flush ceiling and wall installation
In stock · Ships same business day

$133.00 $107.99 Save $25.01
Compare

Out of stock
Vivotek

SKU: AM-10G(RTL)

Vivotek AM-10G RTL Recessed Mounting Kit

Recessed mount for SC9133-RTL camera with flush ceiling/wall install
Special Order · Ships in 2-3 weeks

$107.99

Add to Cart
The item has been added
Compare

Out of stock
Vivotek

SKU: AM-10H

Vivotek AM-10H Recessed Ceiling Mounting Kit

Recessed ceiling mount for Vivotek fisheye domes with flush install
Special Order · Ships in 2-3 weeks

$191.99

Add to Cart
The item has been added
Compare

Out of stock
Vivotek

SKU: AM-10I

Vivotek AM-10I Recessed Ceiling Mount Kit

Recessed ceiling mount for Vivotek PTZ cameras, drop or solid ceiling
Special Order · Ships in 2-3 weeks

$331.99

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Vivotek

SKU: AM-114_V02

Vivotek AM-114_V02 Outdoor Pendant Mount

Pendant mount for Vivotek cameras in outdoor installations
Special Order · Ships in 2-3 weeks

$113.99

Add to Cart
The item has been added
Compare

Out of stock
Vivotek

SKU: AM-116_V02

Vivotek AM-116_V02 Pendant Pipe Mount

1.5" NPT pendant pipe mount, 20mm standoff, indoor/outdoor rated
Special Order · Ships in 2-3 weeks

$45.99

Add to Cart
The item has been added
Compare

Out of stock
Vivotek

SKU: AM-11C_V01

Vivotek AM-11C Bullet Camera J-Shape Mounting Bracket

J-shape aluminum bracket with 360° pan and 56° tilt for Vivotek bullets
- Supports up to 10 kg camera load with full 360-degree rotation
- 56-degree tilt range enables precise vertical positioning for any angle
- Lightweight aluminum construction at 1.2 kg for straightforward wall mounting
Special Order · Ships in 2-3 weeks

$188.00 $151.99 Save $36.01

Add to Cart
The item has been added
Compare

Out of stock
Vivotek

SKU: AM-11F

Vivotek AM-11F Ceiling Mount Bracket 120-180cm

Adjustable ceiling mount, 120–180cm reach, 360° rotation & ±80° tilt
- Aluminum construction with 96-hour outdoor protection for indoor/outdoor use
- 360-degree pan and ±80-degree tilt range for comprehensive camera positioning
- Complete mounting hardware included; fits ceiling heights from 120–180cm
Special Order · Ships in 2-3 weeks

$104.00 $84.99 Save $19.01

Add to Cart
The item has been added
Compare

Out of stock
Vivotek

SKU: AM-11G

Vivotek AM-11G Wall Mount Bracket

Aluminum wall mount bracket for secure outdoor camera installation
- Corrosion-resistant aluminum alloy construction rated for outdoor use
- Compact Ø 70 x 149 mm design at 340 g for space-constrained deployments
- Includes mounting hardware for quick wall installation and secure positioning
Special Order · Ships in 2-3 weeks

$159.00 $128.99 Save $30.01

Add to Cart
The item has been added
Compare

Out of stock
Vivotek

SKU: AM-216

Vivotek AM-216 15-Degree Wall Mount Bracket

Fixed 15-degree wall mount bracket for indoor/outdoor surveillance
- 15-degree fixed tilt angle optimizes camera positioning without pan-tilt
- Durable ABS+PC composite construction rated for indoor and outdoor use
- Compact 90.5 mm diameter design with complete mounting hardware included
Special Order · Ships in 2-3 weeks

$40.00 $32.99 Save $7.01

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Vivotek

SKU: AM-218_V02

Vivotek AM-218_V02 Modular Wall Mount Bracket

Wall, pendant, and rack mounting from one modular bracket
In stock · Ships same business day

$66.99

Add to Cart
The item has been added
Compare

Out of stock
Vivotek

SKU: AM-219

Vivotek AM-219 Dual AI-104 Illuminator L-Shaped Bracket

L-shaped bracket for dual AI-104 illuminators, 12 kg capacity
- Mounts two AI-104 illuminators with adjustable L-shaped positioning
- SPCC steel construction with black powder coat for outdoor durability
- Compact 310 x 90 x 40 mm design, includes complete mounting hardware
Special Order · Ships in 2-3 weeks

$90.00 $72.99 Save $17.01

Add to Cart
The item has been added
Compare

Add to Cart The item has been added
Vivotek

SKU: AM-21A_V02

Vivotek AM-21A L-Shaped Wall Mounting Bracket

L-shaped aluminum wall bracket for fixed and varifocal cameras
- Aluminum alloy construction resists corrosion in commercial installations
- Compact 170 × 110 × 150 mm footprint minimizes wall protrusion
- Pre-drilled mounting holes with included hardware for quick setup
In stock · Ships same business day

$60.00 $48.99 Save $11.01

Add to Cart
The item has been added
Compare

Out of stock
Vivotek

SKU: AM-21B

Vivotek AM-21B Dome Camera L-Shape Mounting Bracket

L-shaped aluminum bracket for Vivotek dome cameras with compact, discreet mounting
- Aluminum alloy construction resists corrosion in indoor and outdoor installations
- L-shaped design optimizes camera angle flexibility and positioning in tight spaces
- Lightweight at 220g with included hardware for quick wall or corner installation
Special Order · Ships in 2-3 weeks

$59.00 $47.99 Save $11.01

Add to Cart
The item has been added
Compare

Out of stock
Vivotek

SKU: AM-21E

Vivotek AM-21E Box Camera Wall Mount Bracket

Aluminum wall mount bracket for Vivotek box cameras, indoor/outdoor
- Aluminum alloy construction rated for indoor and outdoor installations
- Compact 318 x 226 x 108 mm design minimizes visual footprint on walls
- Compatible with Vivotek box camera models for straightforward mounting
Special Order · Ships in 2-3 weeks

$137.00 $110.99 Save $26.01

Add to Cart
The item has been added
Compare

Out of stock
Vivotek

SKU: AM-21G_V01

Vivotek AM-21G L-Shape Dome Camera Bracket

L-shaped aluminum bracket for compact FD8366-V dome camera mounting
- Aluminum alloy construction at 320g fits tight spaces with 135 x 60 mm footprint
- L-shaped design mounts to walls or ceilings for discreet corner and edge placement
- Engineered specifically for Vivotek FD8366-V camera with full hardware included
Special Order · Ships in 2-3 weeks

$53.00 $42.99 Save $10.01

Add to Cart
The item has been added

What to Look For When Buying

The decisions that matter most before you spec.

Load Rating & Vibration Damping

Mounting brackets must support camera weight (typically 0.5–15 lbs for IP cameras) plus wind load in outdoor deployments. Improperly secured cameras cause system failure during critical incidents; select brackets rated for your camera model and environmental stress factors. Gyro mounts and rubber isolators reduce vibration in high-wind or traffic-adjacent zones.

Cable Routing & PoE Management

Mounting kits with integrated cable glands and strain relief prevent cable pinch points and maintain PoE power delivery stability. Conduit clips and backing plates organize cables at the source, reducing troubleshooting time and protecting against accidental disconnection during maintenance.

Material & Corrosion Resistance

Outdoor and coastal installations require stainless steel or powder-coated aluminum brackets to prevent rust and material degradation. Salt spray, humidity, and UV exposure degrade standard steel within 6–12 months; specify 300/316 stainless for marine environments and 6063 aluminum for standard outdoor use.

Installation Standard & Brand Compatibility

Major brands like Axis, Hanwha, and Vivotek design proprietary mounting interfaces alongside VESA and ISO standard mounts. Verify bracket compatibility with your camera model before procurement; cross-brand mounts may misalign optical paths or create cable stress points.

Height, Angle & Optical Alignment

Camera mounting height and tilt affect pixel density and DORI (Detection, Observation, Recognition, Identification) distances. Adjustable brackets allow field-level fine-tuning; fixed mounts require accurate site survey and pre-deployment calculations to avoid costly repositioning after installation.

Conduit Seal & Weatherproofing

Water ingress at cable entry points causes short circuits and sensor corrosion in wet environments. Select kits with silicone gaskets, stainless steel cable glands, and IP67-rated enclosures; test seals during initial deployment to prevent mid-season failures.

Technology Stack

The specs and acronyms that actually affect mounting brackets & kits performance.

VESA Mount Standards (75/100/200 mm)

Standardized hole patterns used by consumer electronics and some IP camera models. Allows universal bracket compatibility across manufacturers, but always verify camera's screw pitch and load rating before mixing brands.

Wind Load Rating (lbs @ mph)

Manufacturers specify maximum wind speed brackets withstand without camera slip or structural flex. Outdoor installations require ratings matching local weather extremes; most outdoor brackets support 60–120 mph sustained winds, but rooftop or exposed mounting may demand 150+ mph ratings.

Stainless Steel Grades (304/316)

Grade 304 resists general corrosion in most climates; Grade 316 adds molybdenum for superior salt-spray tolerance in coastal zones. Galvanized steel (zinc coating) offers cost savings but degrades 3–5 years faster than stainless in humid/marine environments.

Cable Gland Certifications (IP67/IP68)

IP rating indicates water and dust ingress protection at cable entry. IP67 withstands temporary immersion; IP68 is rated for continuous submersion. Select IP67 minimum for outdoor camera mounts, IP68 for wet-room intercoms and dock-area access readers.

Gyro Mounts & Vibration Damping

Rubber or elastomer isolators reduce micro-vibrations transmitted from poles or wind, stabilizing video in high-motion environments. Critical for PTZ cameras on rooftop poles or traffic-adjacent installations; adds 0.5–2 lbs to mounting weight.

Conduit Diameter & Strain Relief

Brackets specify maximum conduit size (typically 0.5–1.5 inches) and cable bend radius. Exceeding bend-radius limits degrades PoE conductor insulation; use clips and backing plates to maintain manufacturer-specified minimum bend radius (usually 4–6 inches for Ethernet).

Typical Deployment Scenarios

Multi-Story Office Lobby (15 cameras, mixed mount types)

Combine ceiling-mount brackets for overview domes at entry points, corner brackets for stairwell coverage, and recessed in-wall mounts for elevator vestibules. Use Hanwha or Axis unified bracket kits to simplify procurement; junction-box assemblies pre-mount cable glands and backing plates, reducing on-site assembly by 40%.

Outdoor Parking Lot Perimeter (24 cameras, 30-ft poles)

Specify heavy-duty pole mounts rated for 80+ mph wind load, stainless steel hardware, and gyro isolation for vibration damping. Include pendant conduit kits with silicone gaskets and IP67 glands; plan cable routing inside pole conduit to protect PoE runs from weather and UV degradation.

Hospital Intercom & Card-Reader Network (40 stations, recessed mount)

Use recessed trim-ring kits designed for flush in-wall mounting at staff stations, nurse calls, and secure doors. Select 316 stainless trim rings; pair with concealed junction boxes to route cables through wall cavities, maintaining clean aesthetics while protecting core network connections from physical damage.

Warehouse Dock & Data-Capture Zone (8 cameras, industrial-grade PTZ)

Heavy-duty PTZ mounts on gantry beams require gyro dampers and reinforced backing plates rated for 20+ lbs static load. Route PoE and pan-tilt control cables through conduit; ensure sufficient power budget per PoE planning guidance for simultaneous motor operation across all units.

Frequently Asked Questions

What's the difference between VESA and proprietary camera mounts?

VESA (75/100/200 mm) are universal screw-hole patterns used by monitors and some IP cameras, allowing mixed-brand bracket compatibility. Proprietary mounts are manufacturer-specific and often integrate cable routing and power connectors for a given camera family. Always verify your camera's mounting interface before ordering; mixing standards can misalign the lens or create cable stress.

How do I choose between wall, pole, and ceiling mounting?

Wall mounts suit indoor hallways and perimeter coverage; ceiling mounts provide overhead overview angles; pole mounts enable tall outdoor installations for parking lots and large perimeters. Consider viewing angle (DORI distance), cable routing (PoE run length), and environmental exposure (rain, wind, UV). Outdoor deployments typically require pole or soffit brackets with stainless hardware and weatherproof conduit seals.

What wind-load rating do I need for rooftop or pole-mounted cameras?

Most outdoor brackets are rated 60–80 mph; rooftop and tall-pole installations in high-wind zones (hurricane, mountain, or exposed coastal areas) require 100–150+ mph ratings. Consult local building codes and weather records for your site. Undersized brackets allow camera drift, misaligning views and degrading identification accuracy over distance.

Why should I use stainless steel brackets in coastal or humid climates?

Standard steel and galvanized coatings corrode within 2–5 years in salt-spray or high-humidity zones, causing bracket failure and camera drop hazards. Stainless 304 resists general corrosion; 316-grade adds molybdenum for superior marine tolerance. The upfront cost (typically 20–40% more) prevents emergency replacement and liability exposure.

What's an IP67 cable gland, and why does it matter for outdoor mounts?

IP67 means the gland prevents dust and temporary water submersion at cable entry points. Water ingress corrodes connectors and shorts PoE circuits, causing mid-deployment failures. Pair IP67 glands with silicone gaskets and stainless fasteners; test seals before final installation to confirm weatherproofing.

Can I use the same mounting bracket for different camera brands?

Only if both cameras share VESA or ISO mounting standards. Proprietary mounts (common in Axis, Vivotek, and Hanwha models) are not interchangeable. Mixing brands often requires adapter plates, which add bulk, cost, and potential optical misalignment. Standardize on one or two manufacturer families per project to simplify spare-parts inventory and on-site troubleshooting.

Mounting Brackets & Kits

Plan Your Deployment

Sub categories

Showing Results for Mounting Brackets & Kits

Vivotek AM-10G Recessed Mounting Kit

Vivotek AM-10G RTL Recessed Mounting Kit

Vivotek AM-10H Recessed Ceiling Mounting Kit

Vivotek AM-10I Recessed Ceiling Mount Kit

Vivotek AM-114_V02 Outdoor Pendant Mount

Vivotek AM-116_V02 Pendant Pipe Mount

Vivotek AM-11C Bullet Camera J-Shape Mounting Bracket

Vivotek AM-11F Ceiling Mount Bracket 120-180cm

Vivotek AM-11G Wall Mount Bracket

Vivotek AM-216 15-Degree Wall Mount Bracket

Vivotek AM-218_V02 Modular Wall Mount Bracket

Vivotek AM-219 Dual AI-104 Illuminator L-Shaped Bracket

Vivotek AM-21A L-Shaped Wall Mounting Bracket

Vivotek AM-21B Dome Camera L-Shape Mounting Bracket

Vivotek AM-21E Box Camera Wall Mount Bracket

Vivotek AM-21G L-Shape Dome Camera Bracket

Browse by Product Family

What to Look For When Buying

Technology Stack

Typical Deployment Scenarios

Top Brands for Mounting Brackets & Kits

Frequently Asked Questions

Related Categories

Engineering Reading