Ubiquiti UACC-G4 DOORBELL PRO POE-GANG BOX-WHITE Mounting Plate
Overview
The Ubiquiti UACC-G4 DOORBELL PRO POE-GANG BOX-WHITE is a purpose-built mounting bracket designed to integrate the Ubiquiti G4 Doorbell Pro PoE camera directly onto a standard single-gang electrical outlet box. This accessory eliminates the need for separate surface-mount frames or wall extensions, allowing your doorbell camera to sit flush or at a slight angle while drawing power via PoE from your network infrastructure. The white finish coordinates with standard electrical trim and blends into most entryways.
Key Installation Features
- Single-Gang Box Compatibility: Mounts directly over a standard electrical outlet box opening without additional framing, reducing installation time and maintaining a clean aesthetic on residential or light commercial entrances.
- Dual Positioning: Supports both flat and angled mounting, giving you flexibility to aim the camera at the entrance from slightly different vertical angles depending on your doorway geometry and viewing requirements.
- PoE Power Pass-Through: The bracket is designed to accommodate PoE connectivity without obstruction, meaning the camera draws its power and network signal through a single Ethernet run — no separate power adapter needed, simplifying wiring on the wall.
- White Finish: Matches standard residential electrical outlet trim and common door frame colors, reducing visual contrast when installed on white or light-colored walls typical in residential deployments.
Integration & Compatibility
This mounting accessory is specifically engineered for the Ubiquiti G4 Doorbell Pro PoE camera model. Verify your camera model before purchase — it will not fit other Ubiquiti doorbell variants or third-party doorbell cameras. When paired with the G4 Doorbell Pro, ensure your PoE network switch or injector can supply adequate power; the G4 Doorbell Pro PoE draws approximately 12.95W under full operation. For multi-doorbell installations or extended cable runs, consult your PoE power budget planning guide to confirm your switch has sufficient available power.
Mounting Considerations
Installation requires access to an existing single-gang electrical box on your door frame or wall. The bracket bridges the gap between the box and the doorbell camera body. Wall material (drywall, stucco, brick) affects ease of installation; ensure the box is securely fastened and the wall around it is stable. For applications where the gang box is recessed or the wall is thick (e.g., masonry), you may need shims or spacers not included with this bracket. Verify your electrical box depth and wall thickness during planning.
Why This Mounting Style Matters
Standard surface-mount doorbell brackets can appear bulky or require additional trim work. Gang box mounting leverages existing electrical infrastructure, reducing visible hardware and creating a more integrated appearance. This is particularly valuable in HOA communities, heritage properties, or professional entrances where a streamlined look is expected. The PoE-powered design — no separate 12V or 24V supply cable — reduces clutter behind the camera and simplifies future relocations or upgrades within the same Ubiquiti surveillance ecosystem.
Frequently Asked Questions
Q: Will this bracket fit the standard G4 Doorbell (non-Pro) model?
A: No. The UACC-G4 DOORBELL PRO POE-GANG BOX-WHITE is designed specifically for the G4 Doorbell Pro PoE. Do not use it with other Ubiquiti doorbell models, as the mounting interface and dimensions differ.
Q: Can I mount this on a double-gang or larger electrical box?
A: No. This bracket is engineered for standard single-gang boxes only. A larger box may not support the bracket's retention points or leave unsightly gaps.
Q: Does this bracket come with electrical wiring or PoE connectors?
A: No. The bracket provides only the mechanical mounting interface. You must supply your own Ethernet cable and PoE power source; the G4 Doorbell Pro accepts a standard RJ-45 PoE connection.
Q: Is this suitable for outdoor entrances exposed to rain and weather?
A: Yes. The white finish is designed for outdoor use, but the bracket itself is not rated for submersion or extreme water spray. Verify that your electrical box installation includes proper weatherproofing and sealing around the Ethernet entry point.
Q: Can I paint the bracket to match my door trim color?
A: The bracket material can accept paint, though durability in sun-exposed areas may vary. Test on a small section first and use exterior-grade paint to minimize weathering and chalking.
Ted PerryPerspective based on aggregated IP Security Depot and affiliated engineering team experience.
The UACC-G4 DOORBELL PRO POE-GANG BOX-WHITE solves a recurring deployment headache: integrating a PoE-powered doorbell camera into an existing electrical box without bulky surface brackets or visible trim extensions. I've seen too many doorbell installs look jerry-rigged because the bracket sat proud of the wall. Gang-box mounting keeps things tight and professional, and the dual positioning (flat or angled) handles most residential door frame geometries without custom trimming.
Technical Highlights:
- Single-Gang Compatibility: Designed to bridge a standard electrical outlet box directly — no extra framing, no surface-mounted wings. This is the right approach for high-visibility entrances where aesthetics matter.
- PoE Power Pass-Through: The bracket doesn't interfere with the RJ-45 connection, so you run one Ethernet cable and the G4 Doorbell Pro draws ~12.95W via 802.3af PoE. Cleaner than separate power injection and fewer cable runs behind the camera.
- Flexible Aiming: Flat or angled positioning lets you dial in the doorbell's field of view without hardware modifications — critical for capturing package delivery and visitor identification at the right angle.
Deployment Considerations:
- Box Depth and Wall Thickness Matter: Recessed electrical boxes or thick masonry may require shims or spacers to achieve flush seating. Measure your box depth and wall construction before ordering; the bracket has limits on how much offset it can absorb.
- PoE Switch Power Budget: A single G4 Doorbell Pro draws ~13W, which is light by PoE standards (well under 802.3af's 15.4W limit). But if you're adding multiple Ubiquiti cameras on the same switch, verify your switch's total power budget doesn't exceed its PSU rating — a single 240W PoE switch can only run about 15 units at max draw.
- Weatherproofing Your Ethernet Entry: The bracket is outdoor-rated, but the Ethernet cable entry point needs sealing. A standard cable gland or even weather-stripping around the Ethernet run prevents water ingress that could short the PoE injector or camera.
Use this bracket when you're mounting the G4 Doorbell Pro PoE in a residential or light commercial setting with an existing electrical box and you want a flush, professional appearance. Skip it if your box is in a deep or unusual location — the limitation is installation geometry, not the bracket's quality. For multi-doorbell residential projects or apartment buildings with standardized electrical trim, gang-box mounting standardizes labor and keeps costs down across the fleet.
