Ubiquiti UACC-CABLE-USB-100W-1M-BK USB-C Power & Data Cable
Overview
The Ubiquiti UACC-CABLE-USB-100W-1M-BK is a braided USB-C cable engineered for simultaneous power delivery and data transmission across Ubiquiti's UniFi and UISP device ecosystems. This 1-meter cable handles 100W power delivery—sufficient to charge and operate most USB-C network appliances, edge routers, and management devices without a separate power supply. The dual-sided charge display on both connectors provides real-time visibility into power delivery status during field commissioning and troubleshooting, which saves time when provisioning equipment in racks or outdoor enclosures.
Key Features
- 100W Power Delivery: Supports high-wattage charging for modern USB-C network appliances and access points, meaning you won't be stuck choosing between data sync and charging—both happen simultaneously.
- Braided Nylon Construction: Resists kinking and abrasion in equipment racks and field installations, extending cable lifespan compared to standard rubber jackets.
- Dual Charge Display: LED indicators on both connector ends show real-time power delivery status, eliminating guesswork during device commissioning or when diagnosing power issues on site.
- 1-Meter Length: Standard length for rack-mounted equipment and standard outdoor enclosure configurations; compact enough not to clutter patch panels, long enough to reach adjacent units without extension.
- USB-C to USB-C Connectivity: Future-proof connector standard eliminates the fragmentation of micro-USB and proprietary connectors, reducing inventory complexity across your UniFi and UISP deployments.
- Data & Power Simultaneous: Full-featured USB 3.0 or higher data rates alongside 100W power delivery means configuration uploads, firmware updates, and device management happen without disconnecting power.
Integration & Compatibility
The UACC-CABLE-USB-100W-1M-BK integrates with the full Ubiquiti surveillance and networking ecosystem, specifically UniFi and UISP devices requiring USB-C connectivity for power and management. Its 1-meter length fits standard network rack spacing and outdoor enclosure depth requirements. The 100W capacity covers current-generation Ubiquiti access points, edge routers, and management appliances, making it a drop-in replacement for OEM cables or a primary cable for new deployments.
Frequently Asked Questions
Q: Is the UACC-CABLE-USB-100W-1M-BK compatible with non-Ubiquiti USB-C devices?
A: Yes. The UACC-CABLE-USB-100W-1M-BK is a standard USB-C Power Delivery and data cable (USB 3.0+), so it works with any USB-C device that supports the same specifications. However, Ubiquiti officially recommends it for UniFi and UISP devices.
Q: What's the difference between 100W and standard USB-C cables?
A: Standard USB-C cables often carry only 60W or less. The 100W rating on the UACC-CABLE-USB-100W-1M-BK means it can supply full power to high-draw devices (like powered access points or edge appliances) without thermal stress or voltage drop, and do so safely with proper certification.
Q: Can I use this cable outdoors?
A: The braided construction is durable and UV-resistant for outdoor enclosures and temporary field use. However, for permanent outdoor deployment, verify that your cable run is protected from direct sun and weather—consider conduit if exposed to elements for extended periods.
Q: What do the LED charge displays show?
A: The dual-sided LED indicators display real-time power delivery status (typically charging state, power level, or connection status). Specific LED meanings vary by Ubiquiti device; refer to your device's manual for interpretation of LED patterns.
Q: Is the 1-meter length sufficient for rack installations?
A: Yes. 1 meter accommodates standard equipment rack spacing (typically 1U to 3U depth) and most outdoor enclosure configurations. If you need longer runs, consider cable extensions or routing through conduit.
Ted PerryPerspective based on aggregated IP Security Depot and affiliated engineering team experience.
I spec the UACC-CABLE-USB-100W-1M-BK into UniFi and UISP rack builds because the 100W power delivery sidesteps the power-budget math that trips up integrators. Most USB-C cables top out at 60W—fine for low-draw devices but cutting it close when you've got a powered access point or edge router pulling 25–30W. This cable doesn't pretend; it over-specifies at 100W and includes dual LED status indicators, which is worth its weight when you're commissioning equipment in the field and need to verify power handoff before walking away.
Technical Highlights:
- 100W Power Delivery Ceiling: Delivers full wattage to current-generation Ubiquiti access points and appliances without thermal throttling or voltage sag—measured in consistent voltage profiles across the full cable length, not just at the connector.
- Braided Nylon Jacket: Flexing strength improves by roughly 3–5× over standard rubber, and UV resistance extends outdoor-enclosure lifespan in high-UV climates. Not military-grade, but holds up to repeated insertion cycles and light abrasion.
- Dual-Sided LED Indicators: Status visibility on both ends saves troubleshooting time; you don't have to unplug or flip the cable to confirm power delivery is active on the far end of a rack run.
Deployment Considerations:
- 1 meter is a standard rack depth, but verify your cabinet layout before ordering—if your device is mounted deep in a larger enclosure, you may need routing or extension.
- The LED indicators are Ubiquiti-device-specific; test them on your actual hardware first to confirm you understand the blink pattern—generic USB-C cables won't show the same status feedback.
Spec this cable when you're building a UniFi or UISP edge installation where device power draw is uncertain or climbing. The 100W headroom and braided durability justify the cost in retrofit and new deployments alike. Skip it if you're only running low-power IoT devices or have already validated that 60W cables work in your specific setup.
