FLIR 61002-1102 PTZ Multi-Sensor Thermal Camera
The FLIR 61002-1102 is a commercial-grade PTZ multi-sensor camera that pairs a 1080p (2MP) visible imager with an uncooled VOx microbolometer thermal detector on a single continuously-rotating head. It is built for perimeter and critical-infrastructure applications where you need to detect a person or vehicle in total darkness, heavy smoke, or fog well before a visible-light sensor could resolve anything useful, then slew the visible channel over to confirm identity. The 61002-1102 covers 360° of continuous pan and a full +90° to -90° tilt range, so a single pole or rooftop mount can watch a complete perimeter without a mechanical stop forcing a blind spot.
Overview
This is a dual-sensor PTZ platform, not a single-imager dome — the thermal channel does detection work while the visible 1080p channel does identification work. That split matters operationally: thermal sensors read heat signatures, so they are largely immune to shadows, glare, and zero-light conditions that defeat conventional cameras, while the visible sensor gives responding personnel a recognizable image once something is flagged. Communication runs over ONVIF Profile S/T and RTSP with H.264 streaming, so the 61002-1102 integrates into existing VMS infrastructure rather than requiring a proprietary viewer.
Key Features
- Uncooled VOx microbolometer thermal detector: no cryocooler to maintain and no warm-up cycle — the thermal channel is on and reading heat signatures the instant power is applied, which matters for a perimeter camera that has to be reliable at 3 a.m.
- 360° continuous pan, -90° to +90° tilt: a single 61002-1102 head can sweep a full circle without a cable-wrap stop interrupting coverage, useful on corner-of-building or rooftop mounts where a limited-rotation PTZ would leave a gap.
- 1080p (2MP) visible channel: gives you enough resolution to identify clothing, vehicle color, and general features once the thermal channel cues an operator or VMS analytic to slew over.
- IP66 environmental rating: rated for direct rain, wind-driven dust, and washdown spray — the expected rating for an outdoor perimeter PTZ, though it is not a submersion rating if the mounting location floods.
- -40°C to 65°C operating range: the 61002-1102 is built to keep running through winter cold snaps and summer heat without a heater/blower kit, which matters for unattended sites like substations, tank farms, and rail yards.
- 24 VAC power: matches the power infrastructure already common on PTZ camera runs and multi-sensor heads, where PoE alone often can't carry the wattage a pan-tilt motor and thermal core both draw.
- ONVIF Profile S/T, RTSP, H.264: standard protocols mean the 61002-1102 drops into an existing ONVIF-conformant VMS without a proprietary driver or plugin.
- FLIR Video Analytics: onboard analytics processing lets the camera flag events at the edge rather than relying entirely on server-side VMS analytics, reducing the load on central processing for perimeter-scale deployments.
- NDAA-compliant: clears Section 889 procurement restrictions, a hard requirement for federal, state, and many critical-infrastructure bids.
Integration & Compatibility
The 61002-1102 speaks ONVIF Profile S/T and streams H.264 over RTSP, which covers the majority of commercial VMS platforms without a custom integration package. Because it is a 24 VAC device rather than a PoE-only unit, plan conduit and a local power source into the install rather than relying solely on PoE switches to run the head — pair it with the correct FLIR power supply for the run distance involved. For sites building out a full perimeter, the 61002-1102 pairs naturally with a network video recorder sized for its H.264 dual-stream output and with a broader FLIR camera catalog of fixed cameras covering shorter-range approaches. Anyone speccing a mixed thermal/visible perimeter should also review a camera selection guide before finalizing coverage zones, since thermal detection range and visible identification range are not the same number and both need to be planned for. The 61002-1102 belongs in the broader PTZ camera category alongside single-sensor pan-tilt-zoom units, but it is the multi-sensor thermal/visible combination that separates it from a standard visible-only PTZ.
Frequently Asked Questions
Q: Is the FLIR 61002-1102 NDAA compliant?
A: Yes, the 61002-1102 is NDAA-compliant, meeting Section 889 procurement requirements for federal and critical-infrastructure deployments.
Q: What is the operating temperature range of the 61002-1102?
A: The 61002-1102 is rated for -40°C to 65°C operation, suitable for unheated outdoor enclosures in extreme climates.
Q: Does the 61002-1102 use PoE power?
A: No, the 61002-1102 is powered by 24 VAC rather than Power over Ethernet, so plan a local 24 VAC power source into the installation.
Q: What is the pan and tilt range on the 61002-1102?
A: The 61002-1102 offers 360° continuous pan rotation with tilt from +90° to -90°.
Q: What VMS protocols does the 61002-1102 support?
A: The 61002-1102 supports ONVIF Profile S/T along with RTSP streaming and H.264 compression for integration with conformant VMS platforms.
Q: What type of thermal detector is in the 61002-1102?
A: The 61002-1102 uses an uncooled VOx microbolometer thermal detector, which requires no warm-up cycle or cryocooling.
The 61002-1102 is the camera I point to when someone tells me their fence-line visible camera keeps missing intrusions at night. Pairing an uncooled VOx microbolometer thermal core with a 1080p visible sensor on one 360°-pan head means the 61002-1102 detects a heat signature first and lets you confirm it visually second — that order matters for perimeter work.
Technical Highlights:
- 360° continuous pan / -90° to +90° tilt: no cable-wrap dead zone, so one 61002-1102 on a corner mount covers a full perimeter sweep instead of two overlapping fixed units.
- -40°C to 65°C operating range: I've specced this unit for unheated substation and rail-yard sites where a standard-rated camera would need a heater blower kit just to survive January.
- IP66 enclosure: handles wind-driven rain and washdown spray on an outdoor pole mount without extra housing.
Deployment Considerations:
- This is a 24 VAC camera, not PoE — budget for conduit and a local 24 VAC supply rather than assuming your PoE switch will run it.
- The thermal channel is 1080p visible-paired, not a fixed lens combo you can swap in the field — confirm detection range needs against the site's longest sightline before final placement.
I'd spec the 61002-1102 for a fence-line or substation perimeter where nighttime intrusion detection is the priority and a VMS operator needs a fast visible confirmation on alarm, not for an interior hallway or retail floor where a fixed dome does the job for less.
