Panduit QSP48HDWH QuickNet 48-Port Modular Patch Panel
Overview
The Panduit QSP48HDWH is a 1U, 48-port modular patch panel from the Panduit QuickNet™ copper cabling line — designed to accept snap-in shielded keystone jacks for structured cabling installations that demand clean port density and flexibility. At 19 inches wide and just 1.73 inches tall, it fits any standard EIA-310 rack or cabinet without burning unnecessary rack space. The QSP48HDWH ships in white and is built for integrators who want a consistent, no-compromise termination point across distribution frames, IDF closets, and horizontal cabling runs.
This panel is a housing — it does not include pre-loaded jacks. That means you select the shielded copper patch panel jacks matched to your cabling category and snap them in, giving you precise control over the channel rating of the finished link. For security and AV/IP deployments where shielded cabling is specified, this approach avoids the cost of replacing an entire panel just because one port fails or a category upgrade is needed.
Key Features
- 48 ports in 1U (19" × 1.73"): Hits the practical density ceiling for a single rack unit — 48 shielded channels terminated and labeled in the same space most competing panels offer 24. That matters in crowded IDF rooms where rack space costs money.
- Modular jack design — future-proof field changes: Snap-in keystone jacks can be replaced individually without punching down new wire or swapping the panel. One bad port or a category upgrade touches only that port, not the whole run.
- Compatible with QuickNet shielded cassettes and jacks: Panduit's QuickNet ecosystem covers Cat5e through Cat6A shielded modules — match the jack to your cable spec and the panel handles the rest. Mixing categories in a single panel is supported as long as the installed jacks are rated appropriately.
- Standard 19" EIA width (482.6 mm): Drops into any standard two-post or four-post rack without adapter rails or spacers. No surprises on installation day.
- White finish: Simplifies color-coded rack organization in environments where white panels distinguish structured cabling from black AV or power infrastructure.
- Sold individually, carton quantity 10: Order single panels for small projects or full cartons for large campus rollouts — pricing scales accordingly.
Integration & Compatibility
The QSP48HDWH is designed for use with Panduit QuickNet shielded keystone modules — verify jack compatibility against your specific cabling category (Cat5e, Cat6, Cat6A) before ordering. The panel itself sets no upper limit on channel category; the installed jacks determine the link rating. It pairs cleanly with standard PoE-capable network switches and patch cord management accessories in 19-inch rack environments. For high-density IP camera or access control deployments where STP cabling is specified, this panel provides a clean, serviceable termination point at the edge distribution frame.
Frequently Asked Questions
Q: Does the QSP48HDWH include jacks or is it a blank panel?
A: The QSP48HDWH is a blank modular housing. It does not include pre-loaded jacks. You must separately order compatible Panduit QuickNet shielded keystone jacks and snap them into the panel ports.
Q: What rack size does the QSP48HDWH fit?
A: It mounts in any standard 19-inch EIA-310 rack or cabinet. The panel is 1U tall (1.73 inches / 43.9 mm) and 19 inches (482.6 mm) wide.
Q: What cabling categories are supported?
A: The panel itself is category-agnostic — the channel rating is determined by the shielded keystone jacks you install. Panduit QuickNet modules are available in Cat5e through Cat6A shielded configurations.
Q: Can I mix different jack categories in the same QSP48HDWH panel?
A: Yes, the modular design allows different jack types across ports. Each port's rating is set by its individual jack — useful in phased upgrade scenarios or mixed-use installations.
Q: Is the QSP48HDWH available in other colors?
A: The QSP48HDWH is the white variant. Panduit offers the QuickNet modular patch panel in other colors within the same product family — check the QuickNet line for alternate options.
The QSP48HDWH is the panel I spec when a project calls for shielded structured cabling and the client wants room to swap jacks without rerunning wire. At 1.73 inches tall and 19 inches wide, you're getting 48 shielded ports in a single rack unit — that's the right density for IDF closets feeding IP camera runs or access control head-end rooms where STP is mandated but rack space is tight.
Technical Highlights:
- 48 ports / 1U (43.9 mm height): Double the port density of a typical 24-port 1U panel in the same footprint — critical when you're trying to consolidate terminations in a half-height wall cabinet.
- Modular jack housing (no pre-loaded jacks): Individual jack replacement means a failed or mis-rated port is a 30-second swap, not a panel replacement and re-termination job.
- 19-inch EIA-310 standard width (482.6 mm): No adapter hardware needed — drops into two-post open frames or enclosed four-post cabinets interchangeably.
Deployment Considerations:
- Budget for QuickNet shielded keystone jacks separately — the QSP48HDWH ships empty and does nothing without them. Confirm your jack SKU matches your cable category before the install date.
- The white finish is a planning detail that matters on large deployments: if your rack standards use color to distinguish structured cabling tiers (white = horizontal, black = backbone), order consistently across all IDF locations up front rather than mixing finishes later.
Best fit for shielded horizontal cabling terminations in commercial security or enterprise LAN deployments — specifically IDF rooms where IP camera density is high, STP is specified, and the team needs the option to upgrade individual ports without full panel changeouts.
