Hanwha SBP-250C Mounting Hole Cover Pack of 5
Overview
The SBP-250C is a five-pack of white polycarbonate mounting hole covers engineered to conceal fastener hardware in finished Hanwha IP camera installations. These covers integrate with Hanwha wall and pole mount systems, delivering a clean aesthetic that matters in client-facing environments—retail showrooms, corporate offices, and hospitality deployments where visible fasteners undermine professionalism. Each cover measures ø263 mm (ø10.35 in) in diameter with a 10 mm (0.39 in) depth, sized to fit standard Hanwha multi-directional dome mount footprints.
Key Features
- White Polycarbonate (RAL 9003): Durable thermoplastic material resists UV degradation and minor physical contact without yellowing or cracking over years of indoor and covered outdoor use. RAL 9003 is a standardized neutral white that matches most ceiling tiles and wall finishes—eliminating the need for custom paint or finishes.
- Pack Quantity (5 covers per pack): Enough to outfit a typical small-to-medium retail or office deployment in a single order. For larger facilities or future maintenance stock, order multiple packs—covers are consumable and may be lost or damaged during service work.
- Lightweight (29.2 g per unit): Minimal weight (0.064 lb) eliminates mounting stress on camera arms or brackets. The cover contributes negligibly to load, so your mount hardware carries full camera weight without fatigue or vibration concerns from accessory mass.
- Diameter ø263 mm (ø10.35 in): Circular footprint larger than typical fastener holes, making installation forgiving even with minor mounting drift or misalignment. The generous coverage area hides screw heads, washers, and bracket attachment points reliably.
- Shallow Depth (10 mm / 0.39 in): Thin profile avoids interference with camera gimbal movement, sensor housing, or bracket articulation. Covers sit flush against the mounting surface without creating mechanical obstructions or aesthetic protrusions.
- Compatible with SBP-250WMW and SBP-400WMW mount systems: These covers are engineered specifically for Hanwha's standard wall and pole bracket line. Verify your mount part number before ordering—wrong mounting base means covers won't sit flush or may drop loose under vibration.
- Professional Finished Appearance: Hides mechanical fastener visibility, screw heads, and bracket attachment points—a detail that separates a professional installation from rough DIY work. Particularly critical on executive floors, customer-facing areas, and high-end retail environments where finish quality is part of the brand experience.
Integration & Compatibility
The SBP-250C is compatible with camera mounting hardware systems including the SBP-250WMW wall mount and SBP-400WMW pole mount. Supported IP camera models when used with these specific brackets include the PNM-C16083RVQ, PNM-C32083RVQ, PNM-8082VT, PNM-9084QZ, PNM-9084QZ1, PNM-9022V, PNM-C9022RV, and PNM-9031RV. Important: covers attach to mounts, not cameras directly. If your camera model is not listed here, cross-reference your mount part number against the SBP-250WMW or SBP-400WMW datasheets to confirm compatibility. Mixing mount families or fastener hole diameters will result in poor fit or non-functional covers.
Deployment Context
The SBP-250C is a non-functional accessory—it does not affect camera performance, analytics, or video quality. Deploy covers at final installation when cable runs are complete, bracket torque is verified, and the system is ready for handoff. In retrofit scenarios where you need to add covers to an existing installation, plan 10–15 extra minutes per camera to loosen the mount slightly and slide covers over fastener heads. Covers are easy to remove if future service requires bracket adjustment or camera removal, so they impose no permanent installation penalty.
Frequently Asked Questions
Q: Will these SBP-250C covers fit my Hanwha dome camera mount?
A: The SBP-250C is designed for SBP-250WMW and SBP-400WMW mounts specifically. If you use a different Hanwha mount family (e.g., SBP-300, SBP-600 series), verify the fastener hole diameter and cover diameter match before purchasing. Consult the mount datasheet or contact your camera supplier if unsure.
Q: Can I install these covers without removing the camera from the mount?
A: Yes. Covers slide over fastener heads after installation is complete. If fasteners are very tight or the mount is rigid, you may need to slightly loosen the mount bracket to guide the cover on, then re-tighten. This typically takes 2–3 minutes per cover.
Q: Are the SBP-250C covers reusable?
A: Yes. Covers are removable and can be installed and removed multiple times without damage to the polycarbonate. If you need to service the mount or adjust the bracket angle, simply lift off the covers, perform maintenance, and reinstall.
Q: Do these covers affect camera performance or field of view?
A: No. Covers are mounted on the bracket below the camera sensor. They do not obstruct the lens, affect video quality, or impact analytics or IR illumination performance.
Q: What is the material composition of the SBP-250C covers?
A: Polycarbonate (RAL 9003 White). This material is durable, UV-resistant, and suitable for indoor and covered outdoor environments. It resists yellowing and cracking over extended use.
Q: How many covers do I need for a typical deployment?
A: Each SBP-250C pack contains 5 covers. For a small retail or office with 5 cameras on wall or pole mounts, one pack is sufficient. Larger facilities should order multiple packs. Consider ordering spare packs for future maintenance or replacement.
Ted PerryPerspective based on aggregated IP Security Depot and affiliated engineering team experience.
The SBP-250C is a straightforward but often-overlooked finishing touch for dome mount installations. At ø263 mm diameter and only 10 mm deep, these white polycarbonate covers (RAL 9003) handle the aesthetic problem most integrators skip: visible fastener hardware. In a retail or corporate environment, that gap between professional installation and sloppy finish often determines whether the client sees a systems integrator or a handyman. The 5-pack arrives with enough quantity for small-to-medium deployments, and at 29.2 g per unit, the weight penalty is nonexistent—your SBP-250WMW or SBP-400WMW bracket isn't carrying cover mass as any kind of stress.
Technical Highlights:
- ø263 mm circular footprint: Larger than typical fastener holes, so installation tolerates minor bracket drift. You don't have to achieve millimeter-perfect alignment to hide screw heads and washers reliably.
- 10 mm depth: Shallow enough to avoid gimbal interference or sensor obstruction. The mount can articulate, adjust, or tilt without the cover catching or protruding into the camera's mechanical envelope.
- Polycarbonate material (RAL 9003 white): UV-resistant thermoplastic that matches standard ceiling tile and wall finishes without yellowing or cracking. Polycarbonate is more durable than ABS or plastic and handles minor bumps or vibration without brittleness.
- Lightweight (0.064 lb each): Negligible mass contribution means zero load-bearing concern. Your bracket carries the camera; the cover doesn't add fatigue or vibration dynamics to the mount system.
Deployment Considerations:
- Covers are specific to SBP-250WMW and SBP-400WMW mounts. If you've got a different Hanwha bracket family or third-party mount, verify fastener hole diameter and cover diameter match before ordering. Wrong size = wasted money and site callbacks.
- Installation is final-stage work—do it after bracket torque verification and cable runs are complete. Covers are removable, but you don't want to loosen and re-loosen mounting hardware multiple times during commissioning. Plan 10–15 extra minutes per camera for retrofit installs where the mount is already under load.
- Stock spares: one 5-pack per 5 cameras is the rule of thumb, but consider ordering a second pack for maintenance reserves. Covers get lost, dropped, or damaged during service calls. Keeping extras on hand prevents site delays when you need to pull and reinstall covers during troubleshooting.
The SBP-250C belongs in any Hanwha dome mount specification where the installation is visible to executives, retail staff, or customers. It's not a performance product—it's a professionalism product. If your bid includes SBP-250WMW or SBP-400WMW brackets and the site is anything other than a warehouse or industrial environment, include covers in the BOM. The client won't thank you for them, but they'll notice their absence.
