APC by Schneider Electric 0M-5886-009 50A 250V 3P-4W 9 Ft Replacement Power Cordset
Overview
The APC by Schneider Electric 0M-5886-009 is a factory-new, heavy-duty replacement power cordset rated at 50A and 250V in a 3-pole, 4-wire (3P-4W) configuration, with a 9-foot run length. This is a purpose-built OEM cable for use with compatible APC by Schneider Electric UPS systems, PDUs, and power distribution equipment where the original cordset requires replacement or a spare is needed on hand. If you maintain a data center, server room, or critical infrastructure environment running high-draw APC equipment, having the correct replacement cordset — not a field-fabricated substitute — is the right call for both safety and warranty compliance.
Key Features
- 50A Continuous Rating at 250V AC: Supports the full load capacity of compatible high-draw APC equipment without derating. At 3P-4W, this cordset handles three-phase or split-phase distribution configurations common in North American data center and industrial deployments — meaning you are not compromising headroom on a loaded PDU or UPS output.
- 3P-4W (3-Pole, 4-Wire) Configuration: The four-wire layout accommodates a neutral conductor alongside the three current-carrying conductors, which is required on many commercial-grade APC PDU and UPS installations. Mismatching this with a 3P-3W cordset on equipment that expects a neutral is a wiring error — confirm your equipment's inlet requirements before ordering.
- 9-Foot Length: The 9 ft (approximately 2.7m) run gives enough slack for standard rack-to-PDU or UPS-to-distribution panel connections in most equipment rack configurations without excess coiling. If your cabinet layout requires a shorter or longer run, verify before installing — excess cordset length coiled tightly in a restricted space can cause localized heat buildup at full load.
- OEM Factory-New Condition: Supplied as a genuine APC replacement part (0M-5886-009), not a third-party substitute. For equipment still under manufacturer warranty or a service contract, using the OEM cordset avoids any compatibility disputes during a service event.
- Cordset #6 Designation: The Cordset #6 designation corresponds to APC's internal cable classification for this voltage, amperage, and connector pairing — use this designation when cross-referencing against your APC equipment's spare parts list or service manual to confirm fit.
Integration and Compatibility
The 0M-5886-009 (also searched as 0M 5886 009) is designed as an OEM replacement for APC UPS and power distribution equipment that ships with or specifies Cordset #6 in the 50A/250V/3P-4W class. Confirm the inlet type and cordset specification in your APC equipment's documentation before ordering — APC fields multiple cordset variants across the same power range, and physical connector compatibility is not guaranteed by voltage and amperage rating alone. Consult the APC equipment service manual or part substitution guide to verify 0M-5886-009 is the listed replacement for your specific model.
Frequently Asked Questions
Q: What equipment is the 0M-5886-009 designed to replace or service?
A: The 0M-5886-009 is an OEM APC replacement cordset in the Cordset #6 / 50A / 250V / 3P-4W class. It is intended for APC UPS systems and power distribution units that specify this cordset in their parts or service documentation. Always verify the cordset designation in your equipment's manual before ordering.
Q: Is the 0M-5886-009 compatible with three-phase power installations?
A: The 3P-4W (3-pole, 4-wire) configuration is used in both three-phase wye and split-phase distribution setups that include a neutral conductor. Whether it suits your specific installation depends on the inlet configuration of your APC equipment — confirm against the equipment's spec sheet.
Q: What is the length of the 0M-5886-009 cordset?
A: The cordset is 9 feet (approximately 2.7 meters) in length, suitable for standard rack-mounted APC equipment to nearby power distribution panels.
Q: Is this a genuine APC part or a third-party replacement?
A: The 0M-5886-009 is supplied as a factory-new OEM original from APC by Schneider Electric — not an aftermarket or third-party substitute.
Q: Can I use the 0M-5886-009 at 120V for lighter loads?
A: This cordset is rated for AC 250V / 50A / 3P-4W applications. Using it outside its intended APC equipment context or in a non-specified configuration is not supported by the available evidence — consult APC's documentation for your specific equipment before deploying.
When a high-draw APC UPS or PDU needs a cordset swap, sourcing the exact OEM replacement matters more than it sounds. The 0M-5886-009 is rated 50A at 250V in a 3P-4W configuration — that neutral wire in the fourth conductor is load-bearing in certain APC distribution topologies, and substituting a 3P-3W cordset where the equipment expects a neutral is a wiring fault, not just a mismatch.
Technical Highlights:
- 50A / 250V Rating: Full-load headroom for compatible APC high-draw equipment — no derating required at rated capacity when the cordset is correctly matched to the inlet.
- 3P-4W Configuration: The four-wire layout is specifically required on APC equipment that uses a neutral conductor in the distribution path; this is not interchangeable with three-wire variants of the same amperage class.
- 9 ft Run Length: Enough reach for most rack-to-panel connections in a standard equipment bay without excess coiling — relevant because tightly coiled large-gauge cordsets at continuous high load are a thermal management concern.
Deployment Considerations:
- Verify the Cordset #6 designation explicitly in your APC equipment's spare parts list or service manual — APC fields multiple cordset variants in the 50A/250V class, and physical connector fit is not guaranteed by electrical rating alone.
- The 0M-5886-009 is listed as non-returnable in the source documentation, so confirming compatibility before ordering is essential — there is no fallback if the connector type does not match your equipment's inlet.
This cordset is the right call for a data center or critical infrastructure environment where an APC high-draw system specifies Cordset #6 as the OEM replacement — particularly in installations where substituting a non-OEM cable would create a service contract or warranty complication.
