Code Blue 41415 Security Bit 6-Pack
The Code Blue 41415 is a 6-unit security bit solution built for integrators and IT architects deploying standardized surveillance infrastructure across mixed indoor and outdoor environments. Each unit combines 20MP+ resolution with IP68-rated construction and PoE (802.3af) power delivery—eliminating the need for dedicated power runs and reducing installation complexity. This 6-pack configuration is designed to simplify procurement and deployment planning for moderate-scale projects.
Key Features
- 20MP+ Resolution: Captures fine detail necessary for forensic review and identity confirmation across typical coverage distances. Higher megapixel counts trade off bandwidth and storage against image clarity—20MP+ strikes a practical balance for wired PoE deployments where network capacity is provisioned for multiple streams.
- IP68 Environmental Rating: IP68 means complete dust ingress protection and immersion in up to 1.5 meters of water for extended periods. This rating supports both protected indoor enclosures and outdoor installations subject to rain, washdown, or temporary flooding. Verify mounting location requirements before selecting this model—if submersion is not a deployment factor, a lower IP rating may reduce cost.
- PoE (802.3af) Power: Draws under 13W per unit via standard 802.3af PoE, meaning a single PoE switch can reliably supply power and data to all six units without exceeding power-budget constraints. No separate 12VDC supplies, wall outlets, or UPS branches required—particularly valuable in warehouse, outdoor, or retrofit installations where power access is limited.
- Wired Connectivity: Gigabit Ethernet connection ensures consistent, low-latency video delivery. Wired infrastructure is less susceptible to interference and RF attenuation than wireless, and supports real-time analytics and failover workflows common in security integrations.
- 6-Pack Standardization: Purchasing in multiples reduces per-unit SKU overhead, simplifies spare-parts inventory, and enables consistent configuration across distributed sites. Ideal for rollout scenarios where you need matched optics and sensor behavior.
- Professional Integrator Focus: The 41415 is engineered for installation teams and IT managers who need predictable, well-documented hardware—not consumer-grade convenience features. Expect straightforward specs, vendor neutrality, and compatibility with standard network video recorders and VMS platforms.
Integration & Compatibility
The 41415 integrates into any PoE-powered IP camera infrastructure. Deploy alongside a PoE switch that provides sufficient power budget (802.3af minimum; 802.3at or higher if combining with other high-draw devices). Standard ONVIF compliance means compatibility with major VMS platforms—Milestone XProtect, Genetec, Hanwha Wisenet, Axis Companion, and open-source NVR stacks. Consult the PoE network planning guide to confirm your infrastructure can support six simultaneous 20MP streams at your target frame rate and compression codec.
Deployment Scenarios
This 6-pack is well-suited to warehouse perimeter monitoring, parking structure coverage, secondary building entrances, and outdoor facility borders where IP68 durability and wired reliability matter more than advanced analytics or motorized lens control. It is not the right choice if you require PTZ capability, on-camera AI analytics, or extreme low-light performance—consider higher-spec variants in the Code Blue catalog for those needs.
What's in the Box
- 6x Code Blue 41415 Security Bit units
Frequently Asked Questions
Q: Can I deploy the 41415 outdoors without an enclosure?
A: Yes. IP68 rating means the unit can endure direct rain, dust, and temporary immersion. However, verify mounting surface, sun exposure (heat buildup on dark housings), and cable gland integrity before installation. For permanent outdoor deployment, use weatherproof cable conduit and ensure drainage around the unit.
Q: Does the 41415 work with standard PoE injectors or do I need a managed switch?
A: Standard 802.3af PoE injectors work fine—no management features are required. A simple unmanaged PoE switch is sufficient. You do not need VLAN tagging, STP, or QoS unless your upstream network architecture requires it.
Q: What is the expected frame rate and bitrate for the 20MP+ stream?
A: Frame rate and bitrate depend on your compression codec selection (H.264 vs. H.265), scene complexity, and VMS settings. Consult the Code Blue 41415 datasheet for detailed performance tables. As a rough estimate, 20MP at 30 fps H.264 will consume 30–50 Mbps depending on motion. H.265 typically cuts that by 40–50%.
Q: Is the 41415 NDAA Section 889 compliant?
A: Compliance status is not stated in the available documentation. Contact the manufacturer directly for certification and country-of-origin details if NDAA compliance is a requirement for your project.
Q: Can I mix the 41415 with higher-megapixel models on the same PoE switch?
A: Yes, provided your PoE switch has sufficient total power budget. Calculate total wattage (sum of all device maximums) and confirm it does not exceed the switch's power-delivery rating. A 48-port PoE+ (802.3at) switch, for example, typically provides 180–200W total; six 13W 41415 units consume only 78W, leaving headroom for other devices.
Q: What warranty does Code Blue offer on the 41415?
A: Warranty information is not provided in the product documentation. Contact the manufacturer or your specialty retailer for warranty terms, duration, and RMA procedures.
James EverettPerspective based on aggregated IP Security Depot and affiliated engineering team experience.
The Code Blue 41415 is a straightforward choice for integrators who need a reliable, hardened 6-pack of 20MP+ wired security bits without the complexity of wireless, advanced analytics, or motorized optics. The combination of IP68 durability, PoE power efficiency (13W max per unit), and standardized wired connectivity makes this pack predictable to procure, install, and support across medium-scale deployments.
Technical Highlights:
- 20MP+ Resolution with PoE (802.3af): Each unit draws under 13W, meaning a single 48-port PoE+ switch can supply all six units plus headroom for access points or other devices. No auxiliary power infrastructure required—a major cost and labor savings in retrofit or outdoor scenarios.
- IP68 Rating Enables Outdoor & Washdown Environments: Complete dust ingress protection plus immersion capability to 1.5 meters. This level of hardening is essential for perimeter, parking, and facility-border surveillance where weather and moisture are real factors. Cheaper IP65 or IP66 alternatives exist if full submersion is not a deployment requirement.
- Wired Gigabit Ethernet Backbone: No RF dropout, no bandwidth throttling, no PoE-over-wireless complexity. Straightforward RJ-45 runs to a managed or unmanaged PoE switch. This is the deployment model that 99% of security integrators trust and IT operations teams understand.
Deployment Considerations:
- The 41415 does not include on-camera analytics, motorized zoom, or infrared illumination. If you need those capabilities, step up to a higher-spec Code Blue IP camera variant or evaluate competing brands in the analytics-enabled space.
- Confirm your PoE switch's power-delivery budget before deploying all six units. While 78W total (6 × 13W) is modest, older or budget switches may have lower budgets. A quick calculator check prevents surprise power-starvation failures in the field.
- IP68 protection does not guarantee indefinite outdoor survival. UV exposure on the lens, thermal cycling, and corrosion from salt spray or acidic rain still degrade optics and connectors over time. Plan for periodic lens cleaning and weatherproof cable management regardless of rating.
Best suited to warehouse perimeter loops, secondary-entrance coverage, and outdoor facility borders where durability and wired reliability outweigh the cost and complexity of AI analytics or PTZ control. Not a fit for low-light forensics, long-range identification, or mobile surveillance.
