Panduit UTP6AX7MGY TX6A 10Gig Cat 6A UTP Patch Cord, 7-Meter, Gray

The Panduit TX6A UTP6AX7MGY delivers true 10GBASE-T performance in a 7-meter (23-foot) unshielded twisted-pair patch cord built for datacenter, enterprise campus, and high-density network environments. Constructed with 24 AWG solid copper conductors and engineered to exceed ANSI/TIA-568.2-D Category 6A and ISO 11801 Class EA specifications, this patch cord supports 10 Gb/s Ethernet, PoE++ (802.3bt Type 3 and Type 4), and provides the headroom needed for demanding IP surveillance, access control, and converged infrastructure deployments where power and data share the same cable plant.

Key Features

• True 10 Gb/s transmission with alien crosstalk suppression via internal foil tape shield structure
• 7-meter (23-foot) length ideal for rack-to-rack interconnects, cross-aisle patching, and MDF/IDF distribution
• 24 AWG solid copper conductors for lower insertion loss and superior channel performance vs. stranded alternatives
• Tangle-free latch design prevents snagging on adjacent cables during moves, adds, and changes
• Pre-installed RapidID barcodes enable one-scan port mapping with Panduit RapidID documentation software
• Rated for 2500 insertion cycles and full IEEE 802.3bt Type 4 PoE++ delivery (up to 90W per port)
• 0.250-inch (6.4 mm) cable diameter balances performance with pathway fill and bend radius constraints
• Exceeds ANSI/TIA-1096-A (formerly FCC Part 68) and IEC 60603-7 modular plug interface standards

Panduit's TX6A patch cord architecture addresses the two primary failure modes in 10GBASE-T copper links: alien crosstalk (AXT) and connector insertion loss. The U/UTP construction incorporates a solid foil tape separator between pairs that limits electromagnetic coupling from adjacent cables—critical in high-density patch panels and cable bundles where AXT can degrade signal-to-noise ratio below the 10 Gb/s threshold. The factory-terminated modular plugs are engineered to maintain pair geometry through the termination point, ensuring return loss and NEXT margins that exceed Category 6A channel limits with overhead to spare. This is particularly important in security and building-management installations where IP cameras, door controllers, and PoE lighting may share the same network infrastructure; a single underperforming patch cord can force an entire switch port to fall back to 1 Gb/s, creating a bottleneck for 4K and multi-imager camera streams.

The 7-meter length hits a deployment sweet spot: long enough to reach from a top-of-rack switch to equipment two racks away or span a typical equipment room to wall-mounted patch panel, yet short enough to avoid the coiling and strain issues that come with excess cable management. Solid conductors (rather than stranded) deliver measurably lower attenuation—on the order of 2-3 dB improvement over equivalent stranded patch cords at 500 MHz—which translates directly to margin in alien-crosstalk-limited environments. The trade-off is reduced flexibility; solid-conductor patch cords are best suited for semi-permanent installations rather than field test leads or desktop fly-leads subject to frequent flexing. For integrators managing large campus networks or datacenter builds, the pre-installed RapidID barcodes are a workflow multiplier: scan the barcode at each end during installation, and Panduit's RapidID software auto-populates port maps, cross-connects, and as-built documentation without manual entry. This cuts commissioning time and virtually eliminates transposition errors that lead to troubleshooting callbacks.

The UTP6AX7MGY is certified to deliver IEEE 802.3bt Type 4 PoE++ (90W per port) over its full 7-meter length, making it a fit-for-purpose choice for high-power IP devices including PTZ cameras with integrated heaters and blowers, 802.11ax (Wi-Fi 6E) access points, and LED lighting controllers. The 2500-cycle plug rating exceeds typical enterprise patching requirements by 10×, and the tangle-free latch design—featuring a strain-relief boot that shields the latch from snag points—reduces the technician time and port damage that comes with conventional clip-on designs. RoHS compliance and CM plenum-equivalent fire rating ensure the cord meets commercial building codes without requiring conduit in most vertical and horizontal pathway applications. For installations demanding verifiable 10 Gb/s performance, Panduit's TX6A patch cords are tested and certified as part of a complete Category 6A channel solution, providing integrators with a single-source warranty path and eliminating finger-pointing when channel certification is required by contract or end-user specification.