Panduit UTP6AX25BL TX6A 10Gig Cat 6A Patch Cord 25 ft

Panduit UTP6AX25BL TX6A 10Gig Cat 6A UTP Patch Cord

The Panduit UTP6AX25BL delivers true 10GBASE-T performance in a 25-foot unshielded patch cord engineered for data center aggregation, server virtualization, and high-density switching environments. Built on 24 AWG solid copper conductors with U/UTP construction, this TX6A™ 10Gig cord exceeds ANSI/TIA-568.2-D Category 6A and ISO 11801 Class EA requirements across the full 1–500 MHz spectrum. Integrated foil tape shields against alien crosstalk in congested cable bundles, while RapidID pre-installed barcodes and a tangle-free modular plug streamline documentation and moves-adds-changes in mission-critical networks.

Key Features

• Exceeds ANSI/TIA-568.2-D Category 6A and ISO 11801 Class EA for 10 Gb/s Ethernet
• 24 AWG solid copper conductors for consistent DC loop resistance and signal integrity
• U/UTP construction with internal foil tape to limit alien crosstalk in bundle scenarios
• Tangle-free modular plug latch prevents snags during installation and simplifies MAC work
• RapidID pre-installed barcode enables automated port mapping with RapidID software
• Supports IEEE 802.3bt Type 3 and Type 4 PoE — up to 100 W over all four pairs
• 0.250-inch (6.4 mm) diameter optimized for high-density pathway fill
• CM flame rating qualifies for horizontal cable runs per NEC Article 800
• Compatible with T568A and T568B wiring schemes for mixed-infrastructure retrofits
• UL 1863 and CSA C22.2 listed (File E129886) for third-party verification

Cat 6A deployments often stumble on alien crosstalk — the electromagnetic interference between adjacent cables bundled in the same pathway. At 10 Gb/s over copper, even minor crosstalk accumulation degrades bit error rate and forces link renegotiation to 1 Gb/s fallback. The UTP6AX25BL addresses this with an internal foil tape wrap that reduces near-end alien crosstalk (ANEXT) and far-end alien crosstalk (AFEXT) to levels well below TIA-568.2-D limits across all 500 MHz. Solid 24 AWG conductors — rather than stranded — minimize DC loop resistance (18.5 Ω per 100 m maximum) and maintain tighter impedance tolerance (100 Ω ±15 Ω), critical when you're pushing 10GBASE-T's ±2.5 V PAM-16 signaling over a full 100-meter channel. The modular plug assembly uses a gold-plated contact interface rated for 750 mating cycles, and the tangle-free latch design eliminates the hook snags that damage conventional RJ45 boots in dense patch panel environments. RapidID barcodes ship pre-applied to each cord and encode asset, length, and port metadata; scanning with the RapidID mobile app or handheld scanner auto-populates your DCIM database and eliminates manual label printing during cutover. PoE support extends through IEEE 802.3bt Type 4 (100 W), so you can deliver full power budget to PTZ cameras, Wi-Fi 6E access points, and LED lighting controllers without mid-span injectors or separate DC home runs.

In the data center, the 25-foot length bridges top-of-rack switches to servers two or three RU away, cross-connects between adjacent racks in the same hot aisle, or IDF-to-IDF horizontal runs where permanent cabling isn't justified. The 6.4 mm outside diameter leaves headroom in 4-inch cable tray and Category D ladder rack without exceeding the 50% fill ratio required by NEC 300.17, and the CM jacket passes UL 1685 (formerly UL 1581) vertical flame propagation — sufficient for plenum-free horizontal spaces but not for return-air ceiling distribution (use Panduit's CMP-rated variant for that). Pair this cord with Panduit Mini-Com TX6A keystone jacks and 48-port angled patch panels to maintain end-to-end component performance margins; mixing vendors can introduce return loss spikes at the plug-to-jack interface that eat into your 10GBASE-T link budget. The tangle-free latch reduces MAC cycle time by 30–40% in field testing — you're not fighting boot snags when you're repatching 200 ports during a 2 a.m. maintenance window. Solid conductors also make the cord stiffer than stranded equivalents, which helps it hold shape in vertical cable managers and reduces the sagging that can pull connectors out of keystones over time.

RapidID integration eliminates the documentation drift that plagues large-scale infrastructure — every scan writes port ID, date, and installer credential to your asset database, so six months later you know exactly which cord landed on switch port Gi1/0/23. UL listing under File E129886 provides the third-party verification required by federal and state procurement specs, and T568A/B wiring compatibility means you can deploy these cords in mixed-pinout environments without repatching existing infrastructure. The solid conductor construction positions the UTP6AX25BL between stranded patch cords (for work-area flexibility) and solid horizontal cable (for permanent links) — ideal for semi-permanent data center cross-connects where you need the replaceability of a cord but the electrical performance of fixed cabling.