Panduit UTP6AX28 10Gig Cat 6A Patch Cord 28 ft

Panduit UTP6AX28 TX6A 10Gig Cat 6A UTP Patch Cord, 28 ft.

The Panduit UTP6AX28 delivers certified 10GBASE-T performance for high-density data center and enterprise network infrastructure. This 28-foot Cat 6A UTP patch cord uses solid foil tape shielding to suppress alien crosstalk in bundled cable runs, maintaining signal integrity at full 10 Gb/s throughput. The tangle-free latch design eliminates snags during MACs (moves, adds, and changes), and factory-installed RapidID barcodes streamline port documentation and asset tracking. Built with 24 AWG solid conductors and rated CM for plenum-alternative in-wall runs, the UTP6AX28 supports IEEE 802.3bt Type 3 and Type 4 PoE++ delivery up to 100W, making it suitable for high-power IP cameras, 802.11ax WAPs, and VoIP endpoints in commercial security and IT installations.

Key Features

• 10Gig Certified Performance: Exceeds ANSI/TIA-568.2-D Category 6A and ISO 11801 Class EA standards for full 10GBASE-T throughput over 100 meters
• Alien Crosstalk Mitigation: Solid foil tape construction limits interference in high-density cable bundles, critical for 40+ cable trunk runs in data centers and server rooms
• Tangle-Free Latch: Snag-resistant boot design enables fast release and reduces latch breakage during frequent patching operations
• RapidID Barcode System: Pre-installed asset tracking barcodes integrate with Panduit's RapidID software for automated port mapping and infrastructure documentation
• PoE++ Compatible: Rated for IEEE 802.3af/at/bt Type 3 and Type 4 delivery, supporting up to 100W power over Ethernet for multi-radio access points and PTZ cameras
• 2,500-Cycle Durability: Rated for 2,500 insertion cycles, 2.5× the TIA minimum, reducing replacement frequency in active patch panel environments
• CM Flammability Rating: Meets National Electrical Code requirements for general-purpose in-wall and ceiling installations outside plenum spaces

The TX6A patch cord uses 24 AWG solid copper conductors in a U/UTP (unshielded twisted pair) construction with a 0.250-inch (6.4mm) outer diameter. The solid foil tape separator between pairs provides a physical barrier that limits alien crosstalk—interference from adjacent cables in the same bundle—which becomes the dominant noise source in Cat 6A and higher installations. This construction is particularly effective in 48-port switch deployments where cable density at the rear of the rack creates electromagnetic coupling between parallel runs. The high-performance modular plugs are terminated to maintain pair geometry through the connector, preserving the 500 MHz bandwidth required for 10GBASE-T signaling. Each cord ships with factory-installed barcodes compatible with Panduit's RapidID asset management platform, allowing installers to scan patch cords during deployment and automatically populate port-to-device mapping in network documentation systems.

In IP surveillance and access control installations, the UTP6AX28 is typically deployed as equipment-to-switch patching for 4K and multi-sensor cameras, high-throughput NVRs, and PoE-powered door controllers. The 28-foot length is optimized for cross-rack connections in small- to mid-size equipment rooms or longer desk-to-wall-jack runs in office environments. The CM jacket rating makes it code-compliant for permanent installation inside walls and above drop ceilings in non-plenum spaces, common in commercial tenant fit-outs and retrofit projects. For integrators managing large-scale deployments, the PoE++ rating (802.3bt Type 3/Type 4) ensures compatibility with current and next-generation powered devices—critical when pre-wiring buildings for future camera upgrades or Wi-Fi 6E/7 access point installations that draw 60W+ at full load. The off-white jacket color matches standard telecom infrastructure and blends with ceiling grid systems, reducing visual impact in finished spaces.

The UTP6AX28 carries UL 1863 listing for communications cable and complies with RoHS hazardous substance restrictions, meeting procurement requirements for federal and state government projects. The 2,500-cycle rating exceeds the TIA-568 minimum by 150%, making it a cost-effective choice for active patch panels in NOCs and server rooms where frequent reconfiguration is standard practice. Panduit ships the UTP6AX28 in single-unit packages with a carton quantity of 10, allowing integrators to order in bulk for multi-building projects while maintaining inventory control at the site level. For installations requiring fire-rated cable in return-air plenums, specify Panduit's CMP-rated TX6A patch cord series; for outdoor or high-EMI environments, consult shielded F/UTP or S/FTP variants within the TX6A family.