Aiphone SBX-AXDV30 30-Degree Angle Box for AX-DV

Overview

The SBX-AXDV30 is a protective mounting enclosure engineered specifically for Aiphone AX-DV series video door stations. This angle box allows you to mount the AX-DV unit at a 30-degree angle on flat wall surfaces, a configuration that becomes necessary when dealing with angled architectural surfaces, overhang limitations, or sight-line optimization at entry points. The enclosure delivers weather resistance and vandal resistance without requiring a separate protective housing system, meaning you avoid dual-layer installation complexity on single-door deployments.

Key Features

• 30-Degree Angle Mounting: Positions the AX-DV door station at 30 degrees from vertical, enabling installation on angled walls or where direct perpendicular mounting would block the camera view or create line-of-sight issues. This eliminates field-workarounds like wedge shims or custom bracket bending.
• Weather-Resistant Enclosure: Protects audio/video circuitry and connectors from direct rain exposure and moisture accumulation. Critical in covered porch or soffit installations where water runoff from walls or roof lines otherwise reaches the door station's rear connector panel.
• Vandal-Resistant Design: Hardened enclosure reduces the likelihood of accidental or intentional damage to the door station during rough handling, cleaning, or contact at high-traffic entries. This is meaningful in multi-tenant or public-access environments where replacement cost and downtime add up quickly.
• Internal Cable Routing Space: Accommodates audio, video, and power cabling inside the box rather than forcing external runs along the wall. Cleaner appearance, reduced exposed cable vulnerability, and simpler future maintenance or replacement of internal connectors without disturbing external weatherproofing.
• Bottom Drainage Opening: Prevents water pooling inside the enclosure if condensation or minor seepage occurs. Ensures long-term integrity of the door station and avoids corrosion of internal terminals that would otherwise require replacement of the entire unit.
• Direct Wall Mounting: Bolts to standard flat wall surfaces using included 8x32 Torx-head fasteners. No additional brackets or adapters needed for the AX-DV — reduces parts inventory and installation time on standardized residential or commercial entry configurations.

Integration & Compatibility

The SBX-AXDV30 is a passive protective accessory — it does not interrupt audio, video, or control signals. The AX-DV door station mounts inside the angle box and retains full functionality within your Aiphone AX-series intercom ecosystem, including call distribution, video transmission, and relay control. Whether you are deploying a single-door system or multiple AX-DV units across a campus or multi-unit residence, each angle box operates independently.

What's in the Box

• 1× 30-degree angle box enclosure
• 1× Set of 8x32 Torx-head fasteners (T-15 drive)

Dimensions & Physical Specifications

Height: 7-11/16 inches. Width: 3-7/8 inches. Depth: 2-7/8 inches. These compact dimensions are scaled to the AX-DV door station profile, ensuring the box sits tight to the wall and does not create an obstruction at doorways or walkways. Verify mounting surface flatness and available wall space before ordering, as the angled profile requires slightly more horizontal clearance than vertical mounting.

When to Choose a Different Approach

If your door station must be mounted perpendicular to the wall (no angle), or if you need a larger protective enclosure for a call station with multiple units, consider alternative mounting accessories in the Aiphone product line. If the AX-DV will be exposed to submersion or extremely harsh UV environments, consult Aiphone technical support for recommendations on secondary protective coatings or alternative installation methods.

Frequently Asked Questions

Q: Does the SBX-AXDV30 work with other Aiphone door station models?

A: No. The angle box is engineered specifically for the AX-DV series. Other Aiphone door station models have different mounting geometries and connector placements. Using this box with a non-AX-DV unit may block access to controls or misalign audio/video ports.

Q: Will the 30-degree angle obstruct the door station's camera view?

A: The angle box itself does not obstruct the camera lens. However, the 30-degree tilt means the camera will point slightly downward rather than straight ahead. Use this if your entry layout benefits from a downward view (e.g., capturing visitors' faces at closer range). For horizontal or upward-looking requirements, a straight wall mount is more appropriate.

Q: Can I install the SBX-AXDV30 on non-flat surfaces?

A: The box is designed for flat wall installation. Curved or heavily textured surfaces may require shims or custom brackets to ensure a weathertight seal. Test fit on-site before final fastening.

Q: Is the enclosure sealed, or will moisture still enter?

A: The enclosure is weather-resistant, not fully sealed. It protects against direct rain and casual spray, but the bottom drainage opening prevents standing water. It is not rated for submersion or continuous high-pressure wash environments. In covered areas (porches, soffits, recessed entries), it performs reliably.

Q: What fasteners are required to mount the box to the wall?

A: The package includes 8x32 Torx-head (T-15) fasteners. Ensure your wall material (wood, concrete, metal stud) is appropriate for the fastener type; you may need to pre-drill pilot holes or use expansion anchors depending on substrate. Refer to local building codes for load and weather rating requirements.

Q: Do I need to remove the angle box to service or replace the AX-DV?

A: Yes. The AX-DV mounts inside the angle box enclosure. To swap or troubleshoot the door station, you will need to unfasten and remove the box. Plan service calls accordingly, and ensure technicians have the appropriate Torx tool on hand.

Ted Perry

Perspective based on aggregated IP Security Depot and affiliated engineering team experience.

The SBX-AXDV30 is a straightforward protective solution for AX-DV door stations on angled wall installations. It solves a common field problem — when your entry architecture or sight-line requirements demand a 30-degree tilt rather than perpendicular mounting. The angle box eliminates ad-hoc bracket bending or shim stacking, both of which complicate future service calls and void manufacturer warranties on the door station itself.

Technical Highlights:

• 30-Degree Angle Geometry: Precisely indexed to position the AX-DV optics and microphone at the target angle without requiring field modification. Prevents the common installation error of over-tilting the door station chassis, which can stress internal circuit board connections and shorten component life.
• Weather-Resistant + Drainage: The bottom opening is not a design flaw — it is intentional. Standing water inside a sealed enclosure causes corrosion faster than open drainage. The weather-resistant sidewalls and top protect against direct rain; the drain prevents condensation pooling. Install in covered areas (soffit, porch overhang) only, not in full-sun open mounting.
• Included Torx Fasteners (T-15): Reduces your fastener inventory and ensures correct gauge for the angle box mounting lugs. Don't substitute standard Phillips or slot-head screws — they don't provide the same hold-down pressure and risk fastener spin-out on stucco or composite walls.

Deployment Considerations:

• The 30-degree angle biases the camera view downward. On tall entries (8+ feet), this is often ideal for capturing visitor faces without needing a secondary downward PTZ. On low or child-height entries, verify the angle doesn't cut off head-and-shoulders framing before committing to the installation.
• Service access requires complete box removal. If your site specification calls for frequent technician visits or remote door station swaps, factor in the extra unfasten/refasten time. On small single-door residential or retail entry retrofits, this is usually a non-issue.
• Wall substrate matters. Concrete anchors (expansion or lag bolts) are appropriate; drywall anchors alone will not hold under vibration or wind load on an angled installation. Specify concrete fastening on your SOW.

Use the SBX-AXDV30 on recessed entry porches or soffit-mounted locations where the AX-DV needs to angle down slightly for optimal visitor capture and the weather-resistant design proves sufficient. Skip it if you need full submersion protection (e.g., exterior wet-weather wall near a pool or fountain) or if your architectural plan demands perpendicular (0-degree) mounting.