Covers & Protection
Sub categories
Showing Results for Covers & Protection
-
STI
SKU: STI-SA5600-G
STI STI-SA5600-G Select-Alert Siren/Strobe Controller
TCP/IP siren/strobe controller for up to 32 concurrent users
- Manages up to 32 concurrent users via TCP/IP for centralized audio-visual alarm control.
- Tamper detection via N.C. 12VDC, 50mA dry contact triggers alert on wall removal.
- Operates at 9VDC across 32°F–120°F, compatible exclusively with Select-Alert systems.
$79.86 $78.99 Save $0.87The item has been added -
STI
SKU: STI-SA5600-R
STI STI-SA5600-R Select-Alert Siren/Strobe Controller
TCP/IP controller for Select-Alert siren and strobe systems, 32 concurrent users
- Coordinates up to 32 concurrent users across Select-Alert siren and strobe zones.
- Built-in tamper detection outputs N.C. 12VDC dry contact signal when unit is removed.
- TCP/IP communication and 9VDC operation simplify network integration and power planning.
$79.86 $78.99 Save $0.87The item has been added -
Add to Cart The item has been addedSTI
SKU: STI-SA5600-W
STI STI-SA5600-W Select-Alert Siren Strobe Controller
- Selects from 32 siren tones at 85 dB or 100 dB to match site alerting requirements.
- Dry relay contact output (12VDC, 50mA, N.C.) integrates directly into existing control loops.
- Tamper switch (N.C. dry contact) triggers alert on wall removal, preventing silent tampering.
$79.86 $78.99 Save $0.87The item has been added -
STI
SKU: STI-TSTAT520F
STI STI-TSTAT520F Single Thermostat Heater Control
- Operates at 9V DC, integrating cleanly into low-voltage access control systems.
- Outdoor-rated for reliable thermal regulation in exposed enclosure deployments.
- Protects door strikes and electronic locks from temperature-induced failures.
$82.68 $81.99 Save $0.69The item has been added -
STI
SKU: STI-TSTAT543F
STI STI-TSTAT543F Dual Thermostat Fan Control & Alarm
Dual-zone thermostat with fan control and alarm for equipment enclosures
- Monitors two independent temperature zones with separate fan control outputs on 9VDC.
- Alarm signaling channels alert on thermal drift before equipment shutdown occurs.
- Wall-mount form factor fits directly inside equipment cabinets for accurate zone sensing.
$124.99The item has been added -
STI
SKU: STI-V34104
STI STI-V34104 4-Channel Voice Receiver
4-channel voice receiver for multi-door access control systems
- Manages voice communication across 4 discrete channels for multi-door deployments.
- Runs on 12VDC via STI-34105 jack-type power supply for straightforward wiring.
- Wall-mount form factor suits access control and intercom integration at entry points.
$126.90 $125.99 Save $0.91The item has been added -
STI
SKU: STI-V34600
STI STI-V34600 Wireless Doorbell Button with Voice Receiver
- Wireless range extends to 1,000 ft line-of-sight, eliminating door-station wiring runs.
- 4-channel receiver with LED zone indicators supports multi-entry monitoring on 12VDC, 75mA.
- Selectable English/Spanish voice announcements suit mixed-language retail or commercial sites.
$152.28 $151.99 Save $0.29The item has been added -
Add to Cart The item has been addedSTI
SKU: STI-V6400WIR4
STI STI-V6400WIR4 Wireless Exit Stopper with Voice Receiver
Wireless exit stopper with voice receiver for access control integration
- Wireless exit stopper with voice feedback receiver
- 9VDC operation - mounts at the exit door for unauthorized egress
- Compact 5.375 x 5.375 x 2 in (137 x 137 x 51 mm) housing
$287.01 $186.99 Save $100.02The item has been added -
STI
SKU: STI-VFC01
STI STI-VFC01 LED Display Cover
- Molded polycarbonate cover protects LED status displays from impact
- Shields LED indicators on access control hardware from contamination
- Drops onto standard LED bezel cutouts on Camden and similar gear
$775.50 $503.99 Save $271.51The item has been added -
STI
SKU: STI-1130-ES
STI Stopper II® con Sirena y Espaciador Claro - STI-1130-ES
- Operates at 28VDC, matching standard access control panel switched outputs.
- Integrated siren and door-holding function share one circuit, reducing wiring runs.
- Clear polycarbonate spacer allows visual striker inspection without disassembly.
$147.98 $146.99 Save $0.99The item has been added -
STI
SKU: STI-1200CP6
STI Stopper II® Contractor 6-Pack Flush Mount - STI-1200CP6
- Flush-mount profile minimizes frame intrusion across single and multi-door deployments.
- Operates at 12VDC or 24VDC, compatible with relay-driven and MOSFET-output strike circuits.
- 6-pack contractor quantity reduces per-unit cost on multi-door access control installs.
$493.55 $296.99 Save $196.56The item has been added -
Add to Cart The item has been addedSTI
SKU: STI-1230CP6
STI Stopper II® Contractor 6-Pack Surface Mount - STI-1230CP6
- Six-unit pack standardizes surface mount hardware across multiple access points in one order.
- Surface mount design eliminates in-wall cavity prep, reducing rough-in time on door frame installs.
- Compatible with standard 4×4 electrical boxes across steel, aluminum, and wood composite frames.
$583.74 $355.99 Save $227.75The item has been added -
STI
SKU: STI-1130CP6
STI Stopper II® Contractor 6-Pack with Horn - STI-1130CP6
- Six-pack format reduces per-unit cost and simplifies bulk deployment across large facilities.
- Integrated 9VDC horn provides audible deterrent without wiring into the fire alarm panel.
- Fits pull stations up to 5-1/2" × 6-3/4"; confirm station depth before ordering.
$841.75 $515.99 Save $325.76The item has been added -
STI
SKU: STI-1100CP6
STI Stopper II® Contractor 6-Pack with Horn Flush - STI-1100CP6
- 95 or 105 dB field-selectable horn triggers instantly on cover lift, alerting staff.
- UV-stabilized polycarbonate rated –40°C to 116°C suits harsh or uncontrolled environments.
- 6-unit contractor pack fits virtually all lever-operated pull stations without modification.
$751.58 $456.99 Save $294.59The item has been added -
STI
SKU: STI-1200A-HTR
STI Stopper II® Heated Enclosure with 4" Deep - STI-1200A-HTR
- NEMA 3R-rated enclosure maintains device operation down to -70°F (-57°C).
- 4-inch deep back box fits standard UL 38/UL 2017 surface-mount pull stations.
- UV-stabilized polycarbonate cover resists weathering while keeping device visible.
$1,099.45 $669.99 Save $429.46The item has been added -
STI
SKU: STI-1230-ES
STI Stopper II® sin Sirena con Espaciador Español - STI-1230-ES
- Spaces and aligns Stopper II assemblies in wall- or surface-mount enclosures.
- Spanish labeling supports multi-language facilities and Spanish-speaking deployments.
- Passive component; no special tools or torque specs required for installation.
$102.46 $101.99 Save $0.47The item has been added
Covers & Protection
Covers and protective enclosures safeguard cameras, intercom devices, and other security equipment from weather exposure, tampering, and accidental damage. Proper protection extends device lifespan and helps maintain consistent system performance in demanding environments.
Plan Your Deployment
- Indoor vs outdoor exposure and weather rating requirements
- Vandal-resistant and impact protection needs
- Compatibility with specific device models
- Mounting method and clearance considerations
- Maintenance access and long-term durability planning
Covers & Protection — Engineering-Grade Installation Accessories for Commercial Deployments
This category covers 250 working models of covers & protection sourced manufacturer-direct or through channel-direct US distribution. Build the rest of your system around the architectural choices below — compatibility, environmental rating, and lifecycle decisions made here propagate through every downstream component you specify.
What to Look For
Compatibility comes first. Mounting brackets, housings, and adapters are specific to the camera or device they support — the same manufacturer often makes parallel lines that don't share accessories. Verify the part number against the camera/device datasheet or compatibility list before ordering. Installation labor consumed troubleshooting a mismatched mount is the most common rework on commercial jobs.
Environmental rating determines material and finish. Indoor accessories typically use steel or aluminum with a powder-coat finish; outdoor accessories need stainless steel or specifically-rated coastal-grade finishes for salt-air resistance. UV exposure degrades plastic over years; choose UV-stabilized polymers or metal for sun-exposed installs. Plan for replacement at year 7-10 on outdoor plastic accessories.
Mounting load capacity must exceed device weight by a healthy margin. Camera weight, housing weight, and any wind loading on PTZs combine. Wall, ceiling, and pole mounts each have rated maximum loads — check before specifying. Pole-mount and pendant-mount installations need conduit, junction boxes, and weather-sealing that aren't always specified in the camera kit.
Wire management and accessibility for service get overlooked in early planning. Bottom-loaded cable entry in housings, swing-out mounting plates, and accessible junction boxes save hours when a camera needs service. Cheap mounts that require complete dismount to access cables drive labor cost up at every service call. Specify service-friendly mounting hardware on installs you expect to service for 10+ years.
Key Specs in This Category
| Spec | Available Options |
|---|---|
| Resolution | 4MP, 2MP, 20MP+, 6MP |
| IP Rating | IP66 |
| Connectivity | Wired |
| Power | PoE+, PoE |
| Type | Lock/Strike, Intercom, Controller, Accessory, Reader, Printer, Dome, Thermal |
| Night Vision | Yes |
Top Brands in This Category
Frequently Asked Questions
Will this mount work with my camera?
Mounts are camera-specific in most cases. The product description and manufacturer's compatibility list are the authoritative source. If you're not certain, send the camera model and the mount part number to our Senior Specialists; we'll confirm compatibility before you order. Returning a mismatched mount after installation labor is significantly more expensive than checking up front.
Do I need a junction box?
For most outdoor and exposed-conduit camera installs, yes — junction boxes house cable terminations and protect splices from weather. The camera's mounting requirements often specify the junction-box size and material. Some camera-and-mount combinations integrate the junction box into the mount; others require a separate box. Confirm before ordering to avoid pulling cable into an installation that can't accept it.
What's the difference between a wall mount and a pendant mount?
Wall mounts attach to vertical surfaces and project the camera outward. Pendant mounts attach to ceilings or overhead structures and suspend the camera below. Pole mounts are a specialized wall mount for poles. Choose by the mounting surface available and the field-of-view orientation required; many cameras work in any mount with the right adapter.
Are stainless steel mounts worth the extra cost?
For outdoor coastal installs (within ~5 miles of saltwater), yes — galvanized steel rusts visibly within 2-3 years in coastal air. For inland outdoor, marine-grade is overkill; powder-coated galvanized lasts 10+ years. For corrosive industrial environments (chemical plants, wastewater), stainless steel or specifically-rated coatings extend service life dramatically. Match the material to the environment, not the budget pressure.
Can I use one brand's mount with another brand's camera?
Sometimes — many mounts accept standard mounting patterns (¼-20 thread, M6 pattern, VESA spacing) and cross brands. Manufacturer-specific cast housings rarely do. Check the mount's hole pattern and weight rating against the camera's specs. When in doubt, use the camera manufacturer's recommended mount; cross-brand savings on mounts are typically small and the warranty implications of mismatched hardware aren't worth the risk.
Need help choosing? Talk to a Senior Specialist — direct line 877-277-7147 or request a quote.