IP Camera Accessories | Mounts, Enclosures, Lenses, IR & Power

Deployment Considerations

Environmental protection and weather resistance
Mounting stability and load support
Power and voltage compatibility
Cable management and termination quality
Compliance with local safety standards

Sub categories

Showing Results for Accessories

Compare

Out of stock
Pelco

SKU: OHEPS20

Pelco OHEPS20 Housing Power Supply 230Vac to 24Vac

230Vac to 24Vac converter for Pelco outdoor camera housings
- Powers heater, blower, and wiper motor systems simultaneously
- 20% operational headroom matched to integrated housing accessories
- Indoor/enclosed installation in dry, ventilated location required
Special Order · Ships in 2-3 weeks

$35.48 $26.99 Save $8.49

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: OHEPS25

Pelco OHEPS25 230Vac to 24Vac Power Supply

230Vac to 24Vac power supply for European outdoor housing accessories
- 400 mA output rated for single heater or wiper motor loads
- Converts European 230 Vac input to regulated 24 Vac output
- NDAA Section 889 compliant for regulated installations
Special Order · Ships in 2-3 weeks

$50.16 $36.99 Save $13.17

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: OHOTS

Pelco OHOTS Sunshield for OptiView Camera Housing

Thermal sunshield for OptiView housings in high-sun outdoor sites
- Reduces solar load and internal temperature in desert/equatorial climates
- Commercial-grade composite construction for OptiView housing family fit
- NDAA Section 889 compliant for government and regulated deployments
Special Order · Ships in 2-3 weeks

$11.34 $7.99 Save $3.35

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: OHOVPOEIPM

Pelco OHOVPOEIPM PoE IPM Retrofit Kit

PoE retrofit for HOV housings—single-cable power, no external supply
- Integrates camera, heater, and blower power through PoE+ (802.3at)
- Converts existing HOV series housings to network-powered operation
- IP66/IP67 rated outdoor housing with IK10 impact resistance
Special Order · Ships in 2-3 weeks

$222.78 $163.99 Save $58.79

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: OHOVPS1B

Pelco OHOVPS1B Housing Power Supply 12Vdc

Universal 12Vdc supply for Pelco OHO camera housings, 100–240V input
- 100–240 Vac input with no selector switch for global deployments
- 12 Vdc output purpose-built for Pelco OHO-series housings
- NDAA Section 889 compliant for government and critical infrastructure
Special Order · Ships in 2-3 weeks

$44.82 $32.99 Save $11.83

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: OHOVPS2B

Pelco OHOVPS2B Power Supply 230V to 24V AC

230V to 24V AC converter for Pelco OHO surveillance housings
- Converts European 230 Vac mains to regulated 24 Vac output
- Compact mount-ready design fits OHO-series camera housings
- NDAA Section 889 compliant for government surveillance projects
Special Order · Ships in 2-3 weeks

$35.48 $26.99 Save $8.49

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: OHOVV1

Pelco OHOVV1 OHO Housing Heater Fan 12Vdc

Internal heater fan for OHO housings suppresses condensation in cold climates
- 12Vdc continuous-duty operation maintains minimum temperatures year-round
- Active air circulation prevents window condensation and optical degradation
- OHO-series housing compatibility only; confirm model before ordering
Special Order · Ships in 2-3 weeks

$32.15 $23.99 Save $8.16

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: OHOVV2

Pelco OHOVV2 OHO Housing Heater Fan 24Vac

24Vac heater fan for OHO housings with condensation suppression
- Continuous-duty operation maintains temperature in outdoor environments
- Active window condensation suppression via warm air circulation
- Direct integration with Pelco OHO-series housings, no transformer needed
Special Order · Ships in 2-3 weeks

$32.15 $23.99 Save $8.16

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: OHOVV3

Pelco OHOVV3 OHO Housing Heater Fan 100-240V

24/7 heater fan for OHO housings; suppresses condensation in cold climates
- 100–240 Vac universal input; no voltage selector switch needed
- Continuous-duty operation maintains window clarity and thermal stability
- Integrates directly into OHO-series Pelco camera housings
Special Order · Ships in 2-3 weeks

$64.03 $47.99 Save $16.04

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: OHPVCF3

Pelco OHPVCF3 Housing Blower Kit Thermo Filter

Thermostat blower kit with integrated filter for hot-climate camera housings
- Temperature-activated operation runs only when needed; 110–240 Vac universal input
- Integrated dust/debris filter protects optics in high-solar-load installations
- IP66/IP67 rated; NDAA Section 889 compliant for regulated deployments
Special Order · Ships in 2-3 weeks

$71.37 $52.99 Save $18.38

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: OHPVPOEIPM

Pelco OHPVPOEIPM VERSO Housing PoE IPM Retrofit Kit

PoE retrofit kit for VERSO HPV housings with single-cable power
- PoE+ (802.3at) power and data over one Ethernet cable to camera
- Fits existing Pelco VERSO HPV-series outdoor housings for retrofit
- NDAA Section 889 compliant for government and critical infrastructure
Special Order · Ships in 2-3 weeks

$222.78 $163.99 Save $58.79

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: OHPVTA1

Pelco OHPVTA1 Housing Tamper Switch and Key Kit

Tamper alarm kit with keyed access control for Pelco housings
- Triggers VMS alarm instantly when housing opened without authorization
- Tamper-proof screws and keyed tool restrict access to authorized personnel
- NDAA Section 889 compliant for government and regulated installations
Special Order · Ships in 2-3 weeks

$36.42 $26.99 Save $9.43

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: OHPVV1

Pelco OHPVV1 Housing Heater Fan 12Vdc

12Vdc heater-fan for Pelco housings; heating and condensation control
- Continuous-duty 12Vdc operation maintains thermal conditions year-round
- Dual heating and air circulation suppresses window condensation in cold climates
- NDAA Section 889 compliant for government surveillance deployments
Special Order · Ships in 2-3 weeks

$32.15 $23.99 Save $8.16

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: OHPVV2

Pelco OHPVV2 Housing Heater Fan 24Vac

24Vac heater-fan for Pelco housings; prevents condensation in cold climates
- Continuous 24Vac operation uses existing pan/tilt power—no extra transformer needed
- Integrated heating and ventilation eliminates window fog on camera optics outdoors
- IP66/IP67 rated, NDAA Section 889 compliant for government surveillance deployments
Special Order · Ships in 2-3 weeks

$32.15 $23.99 Save $8.16

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: OHPVV3

Pelco OHPVV3 Housing Heater Fan 100-240Vac

Universal 100–240V heater fan for Pelco camera housings, 24/7 operation
- Continuous-duty heating and fan circulation prevents condensation in outdoor housings
- 100–240 Vac input works globally without voltage selection or SKU swaps
- NDAA Section 889 compliant for government and regulated sector deployments
Special Order · Ships in 2-3 weeks

$64.03 $47.99 Save $16.04

Add to Cart
The item has been added
Compare

Out of stock
Pelco

SKU: OMPXCRWRENCH

Pelco OMPXCRWRENCH Camera Ring Wrench Tool

Ring wrench tool for Pelco OMPX Series camera housings
- Steel construction designed for controlled torque during housing installation and maintenance
- Prevents cross-threading and surface damage to camera housing ring threads
- NDAA Section 889 compliant for government and institutional surveillance deployments
Special Order · Ships in 2-3 weeks

$233.45 $171.99 Save $61.46

Add to Cart
The item has been added

What to Look For When Buying

The six decisions that matter most before you spec.

Match Bracket to Camera + Surface

A dome camera mounted on a textured wall needs a wall-mount adapter with a gasket; mounted on a pole it needs a pole-mount arm; mounted on an eave it may need a pendant. Third-party brackets exist but brand-specific brackets include proper camera cable routing and weather gasketing. Buying a $40 generic bracket to save on a $80 Axis bracket usually costs more in installation time.

Enclosure NEMA Rating

NEMA 3R = light rain; NEMA 4 = splash + driving rain; NEMA 4X = above + corrosion resistance (coastal, industrial); NEMA 6 = temporary submersion. For weather-exposed camera enclosures, NEMA 4X is the commercial standard. For mission-critical outdoor gear, pair NEMA 4X enclosure + IP67 camera + IK10 vandal rating.

C/CS-Mount Lens Selection

Box cameras use interchangeable C-mount (17.526mm flange) or CS-mount (12.5mm flange). Lens focal length + sensor size determines field of view: a 4mm lens on a 1/3" sensor gives ~60° horizontal FOV. Our DORI guide covers lens selection by scene distance. F-stop matters for low-light; P-iris for auto-exposure.

IR Illuminator Wavelength

850nm IR is more efficient but produces a faint visible red glow (deterrent or accidental giveaway, depending on use case). 940nm is truly covert but requires ~2x the power for the same effective range, and many cameras have lower sensitivity at 940nm. Match illuminator wavelength to camera IR-cut filter spec, or image washout results.

Power Supply Sizing & Distance

12VDC cameras at 100ft from a power supply drop significant voltage over 18-gauge wire — a camera rated for 12V may see 10.5V at the camera end under load, triggering brownout resets. For long runs, use a higher-voltage power supply (24VAC or 48VDC) and step down at the camera. UL-listed surveillance power supplies (Altronix) publish voltage-drop tables.

Cable Jacket Rating

Indoor Cat6 is rated CM (communications); plenum-rated CMP is required for above-drop-ceiling runs per NFPA 70. Outdoor/direct-burial Ethernet is a different product (CMX, direct-burial gel-filled). Mixing jacket ratings causes code violations and fire inspector rejections. Always spec by run environment, not lowest-cost SKU.

Technology Stack

The specs and acronyms that actually affect outdoor performance.

NEMA vs IP Rating Systems

NEMA is the US enclosure standard (NEMA 1-13); IP is the international standard (IP00-IP68). Rough crosswalk: NEMA 4 ≈ IP66, NEMA 4X ≈ IP66 + corrosion, NEMA 6 ≈ IP67. Some spec sheets list both; when only one is given, the crosswalk is approximate. For coastal, industrial, and food-processing environments, specify NEMA 4X or IP66 + stainless steel.

C-Mount vs CS-Mount Lenses

C-mount: 17.526mm flange focal distance. CS-mount: 12.5mm flange. CS cameras accept both lens types (C lenses need a 5mm adapter ring); C cameras accept only C lenses. Most modern box cameras are CS-mount for lens flexibility. Lens thread is 1-inch × 32 TPI on both.

F-Stop / Iris

F-stop = focal length ÷ aperture diameter. Lower F-stop (wider aperture) means more light, better low-light performance, shallower depth of field. F1.4 is very low-light capable; F1.8 is common commercial spec. P-iris (precise iris) lenses auto-adjust aperture based on scene lighting — reduces over-exposure during day, improves low-light at night.

850nm vs 940nm IR

IR illuminators at 850nm are more energy-efficient and the sensitivity of most camera IR-cut filters peaks here — but 850nm produces a faint visible red glow from the LEDs. 940nm is invisible to human eye but requires ~2x the power or shorter effective range. Many covert-deployment cameras are re-tuned for 940nm sensitivity.

UL-Listed Power Supplies

Underwriters Laboratories listed power supplies meet safety standards for overcurrent, overvoltage, and enclosure isolation. UL 294 specifies additional requirements for access control; UL 603 for security burglary; UL 1310 for Class 2 power. Insurance and code requirements increasingly specify UL-listed supplies — particularly in commercial and institutional installations.

Plenum vs Riser vs PVC Cable

Plenum-rated (CMP) cable uses low-smoke FEP jacket for use above suspended ceilings where smoke spreads through return-air plenums. Riser (CMR) is for vertical shaft runs between floors. PVC (CM) is for open office runs only. Using CM in plenum spaces violates NFPA 70 — costly inspector rejection if caught.

Typical Deployment Scenarios

New Construction Retrofit

Cat6A plenum cable pulled to camera locations with proper service loops, 2-gang electrical boxes at each dome location with weatherproof backbox, Cat6A patch panel at the IDF, UL-listed power supplies for any 12V/24V camera, labeled and tested before cameras are mounted.

Coastal / Corrosive Environment

NEMA 4X stainless-steel enclosures for outdoor cameras, 316-grade stainless brackets, silicone dielectric grease on every connector, hot-dipped galvanized or powder-coated steel poles. Budget 15-25% more on accessories vs. standard outdoor — and plan for 3-5 year inspection cycles rather than 10.

Box-Camera LPR Application

Box camera with 50-150mm telephoto lens, dedicated 850nm IR illuminator at same height as camera, pole-mount bracket with junction box, UL power supply for camera + illuminator. LPR-specific enclosures with anti-reflective glass to avoid nighttime IR bloom. Typical deployment: dedicated lane camera, not general-purpose surveillance.

Parking Garage Retrofit

Existing analog coax cable replaced via NVT Phybridge or similar PoE-over-coax, vandal-resistant dome enclosures at ground level, low-profile bullet cameras on ceiling, LED-plus-IR-compatible illuminators to handle harsh fluorescent lighting. Enclosures rated for vehicle-exhaust environment.

Frequently Asked Questions

Do I need the OEM bracket for my camera, or will a generic bracket work?

For most commercial installations, specify the OEM bracket. Brand-specific brackets include proper cable routing, gasketed weather seals, and mounting-hole patterns matched to the camera — which matters more than the cost savings of a generic bracket. Generic brackets are acceptable for indoor standard-dome cameras on flat surfaces; for outdoor, vandal-rated, or pendant applications, use OEM.

What NEMA rating do I need for outdoor camera enclosures?

NEMA 4 for most weather-exposed deployments (driving rain, snow). NEMA 4X for coastal, industrial, or food-processing environments (adds corrosion resistance — typically stainless steel or fiberglass construction). NEMA 6 for temporary submersion or flood-prone areas. The IP-rating equivalent is IP66 for NEMA 4, IP66 + corrosion for NEMA 4X, IP67 for NEMA 6.

How do I choose the right lens focal length for a box camera?

Work backward from the scene. Identify the farthest point you need identification-grade coverage, use our DORI guide to calculate required pixels-per-foot at that distance, and match lens focal length + sensor size to deliver that PPF. A 4mm lens on a 1/3" sensor covers ~60° horizontal FOV; a 12mm lens on the same sensor covers ~20°. Wide FOV = shorter identification distance.

What's the difference between 850nm and 940nm IR illuminators?

850nm is more energy-efficient — you get more effective range per watt — but produces a faint visible red glow from the LEDs. 940nm is truly invisible to the human eye but requires about 2x the power for equivalent range, and many cameras have lower sensor sensitivity at 940nm. For deterrent visibility or cost-efficient long-range, 850nm; for covert applications, 940nm.

Can I power an IP camera with a generic 12V wall-wart?

Not for a commercial deployment. Generic wall-warts are unregulated, not UL-listed for security applications, and typically don't include surge protection. Use a UL-listed surveillance power supply (Altronix AL series, UL 294 or UL 603) with battery backup where required. PoE is preferred when possible — single cable, centralized power management, UPS-backed.

What cable jacket rating do I need for in-ceiling runs?

Plenum-rated (CMP) cable is required for any run through a return-air plenum space above suspended ceilings (most commercial buildings). Riser (CMR) for vertical shafts between floors. PVC (CM) for open office spaces only. Using non-plenum cable in a plenum space is a fire-code violation under NFPA 70 and will be rejected by inspectors. Budget plenum cable for any building where you're not 100% sure of the return-air path.

Accessories

Deployment Considerations

Sub categories

Showing Results for Accessories

Pelco OHEPS20 Housing Power Supply 230Vac to 24Vac

Pelco OHEPS25 230Vac to 24Vac Power Supply

Pelco OHOTS Sunshield for OptiView Camera Housing

Pelco OHOVPOEIPM PoE IPM Retrofit Kit

Pelco OHOVPS1B Housing Power Supply 12Vdc

Pelco OHOVPS2B Power Supply 230V to 24V AC

Pelco OHOVV1 OHO Housing Heater Fan 12Vdc

Pelco OHOVV2 OHO Housing Heater Fan 24Vac

Pelco OHOVV3 OHO Housing Heater Fan 100-240V

Pelco OHPVCF3 Housing Blower Kit Thermo Filter

Pelco OHPVPOEIPM VERSO Housing PoE IPM Retrofit Kit

Pelco OHPVTA1 Housing Tamper Switch and Key Kit

Pelco OHPVV1 Housing Heater Fan 12Vdc

Pelco OHPVV2 Housing Heater Fan 24Vac

Pelco OHPVV3 Housing Heater Fan 100-240Vac

Pelco OMPXCRWRENCH Camera Ring Wrench Tool

Browse by Product Family

What to Look For When Buying

Technology Stack

Typical Deployment Scenarios

Top Brands for Outdoor Deployments

Frequently Asked Questions

Related Categories

Engineering Reading

Certified Experts

Manufacturer Authorized

Expert Access

Since 2014

Brands

Categories

IP Cameras

Ordering

Legal

Company

Sales & Expert Advice

Customer Service